Al-LiBH4复合材料的制备与产氢性能

采用机械球磨法制备了Al-LiBH4系列铝基复合材料.该材料的产氢性能和X射线衍射(XRD)分析结果表明,反应温度升高有利于金属铝和LiBH4之间的相互促进作用,提高材料的氢气产量及产率.常温下该复合材料与水反应迅速,氢气产量高.球料比30∶1、球磨5 h制备的Al-25%LiBH4复合材料30 min内每克材料可以产生720 mL氢气;当反应温度升高至90℃时,在30 min内的氢气产量高达2026 mL/g,氢气产率达95%;而在90℃反应时Al-30%LiBH4材料的氢气产量为2211 mL/g,氢气产率在96%以上.     

Mg1-xTixNi(0≤x≤0.4)系列合金的合成及性能研究

采用机械合金化法成功制备了Mg1-xTixNi(0≤x≤0.4)系列三元合金.XRD结构分析表明,不同成分的合金在相同的球磨时间下非晶化程度有所区别,并且合金的非晶化程度随着球磨时间的增加而趋于完全.少量Ti的加入使得该系列合金的电化学性能及循环稳定性都有所提高.在球磨120h的该系列合金中,Mg0.9Ti0.1Ni合金的最大初始放电容量达到356.85mA·h·g-1(100mA·g-1,-0.5Vvs.Hg/HgO),而Mg0.7Ti0.3Ni合金的循环稳定性最好.Ti的加入亦提高了合金的抗腐蚀性能,使其腐蚀电位正移.     

鲁米诺-8-羟基喹啉-5-磺酸-镉(Ⅱ)-过氧化氢化学发光体系研究

报道了Cd(Ⅱ)对鲁米诺-8-羟基喹啉-5-磺酸-过氧化氢体系的化学发光具有增强作用的实验事实,建立了测定Cd(Ⅱ)的分析方法.该法线性范围为2.0×10~(-8)～1.0×10~(-6)g/mL;相对标准偏差为3.5%;检出限为1.0×10~(-8)g/mL.用于合金样品中Cd(Ⅱ)的分析,结果良好.     

电感耦合等离子体发射光谱法测定铀钼合金中钼EI北大核心CSCD

采用电感耦合等离子体发射光谱(ICP-AES)法测定铀钼合金中钼含量,考察了合金溶解、溶液中钼水解以及铀钼萃取分离等条件。确定溶液中H+浓度在3 mol/L时,铀钼合金在24 h内不会发生水解。选择发射波长202.031 nm为分析谱线。铀钼合金中钼含量在10~160μg/mL范围内呈线性关系,线性方程为y=3614.4x-1978,相关系数为0.9998,方法相对标准偏差小于1%。     

移动氢源用铝合金制氢技术研究

铝具有资源丰富、价格低廉、易保存、水解产氢量大(1244mLg-1)等特点,是NaBH4水解产氢的理想替代品[1].本文用机械球磨法制备了系列铝合金,并对其与水反应产氢的性能进行了研究.结果表明:锡和铋能提高铝的活性,其与铝形成的合金能在常温下与水反应.但铝锡合金在常温下与水反应速度缓慢,而铝铋合金能与水迅速反应,产氢率可达80%.     

MgNi-x% TiNi0.5Mn0.5 (x＝10, 30, 50)贮氢合金的制备与电化学性能

用机械合金化法成功制备出MgNi和TiNi0.5Mn0.5合金, 并将不同质量的TiNi0.5Mn0.5与MgNi合金球磨复合10 h制备MgNi-x% TiNi0.5Mn0.5 (x＝10, 30, 50)合金. XRD结果表明球磨后几种合金均为非晶体, TiNi0.5Mn0.5均匀分散到MgNi合金主相中; 充放电结果表明MgNi-TiNi0.5Mn0.5复合合金的初始容量比纯MgNi合金(443.12 mAh/g)低, MgNi- 10% TiNi0.5Mn0.5首次放电容量是394.46 mAh/g, 但循环寿命有较大的改善, 50次循环后容量保持在232.57 mAh/g, 保持率达59%; 动电位扫描结果表明复合后合金电极抗腐蚀能力提高; 循环伏安法和电化学阻抗谱法研究结果表明: 复合后电极表面的电化学催化性能增强, H原子在合金电极内部的扩散阻抗减小.     

底物水解预处理对玉米秸秆发酵生物产氢的影响

水解预处理是影响纤维索类生物质发酵产氢效率的关键因素之一.在批式试验条件下,分别采用乳酸处理(方法A),生物处理(方法B)和生物/乳酸两步处理(方法C)方法对玉米秸秆进行糖化水解预处理;考察了水解预处理对产氢效率的影响.结果表明:经乳酸预处理、生物预处理和乳酸/生物两步处理的玉米秸秆的累积氢产量分别为132 mL/g,...     

电感耦合等离子体原子发射光谱法测定铂铑合金中铑

提出了电感耦合等离子体原子发射光谱法测定铂铑合金中铑含量的方法。含铑(wRh≤40%)的铂铑合金称样0.1000 g,用盐酸-硝酸(3+1)溶液10 mL和氢氟酸(ρ=1.18 g·mL-1)0.5 mL于微波消解仪中消解完全。选择波长为343.489 nm的谱线作为测定铑的分析线。方法的检出限为0.029 mg·L-1。方法用于分析5个铂铑合金样品,测定值与国家标准方法测定值的相对误差在0.10%~0.40%之间,回收率在99.6%~101.0%之间。     

球磨改性对(Ti Cr)_(0.497)V_(0.42)Fe_(0.083)/30%(w)(LaRMg)(NiCoAl)_(3.5)合金复合电极材料储氢和电化学性能的影响

以钒基合金(Ti Cr)0.497V0.42Fe0.083为基体,添加30%(w)稀土系A2B7型合金(LaRMg)(NiCoAl)3.5为电催化活性材料,采用机械球磨改性制备了储氢合金复合电极材料,研究其储氢特性和电化学性能.X射线衍射(XRD)、扫描电镜(SEM)和透射电子显微镜(TEM)分析结果表明,随球磨时间增加(t=0,0.5,1,3,5,10h),复合材料颗粒逐渐细化,A2B7型合金颗粒分散并包覆在钒基合金表面上;当球磨时间t≥5h时,复合材料形成明显的复合纳米晶组织并伴有部分非晶化倾向,同时钒基合金BCC相结构的晶胞参数a和晶胞体积V均明显减小.合金储氢特性及电化学性能分析测试结果表明,铸态纯钒基合金的吸氢量为3.11%(w),而球磨复合材料的储氢量随球磨时间增加呈减小的规律,其最大储氢量为2.47%(w);球磨改性后,复合材料电极的电催化性能得到明显改善,当球磨时间t≥3h时最大放电容量达到425.8mAh·g-1,经100次充放电循环后该电极的容量保持率(C100/Cmax)为97%,表现出良好的电极循环稳定性.     

离子色谱-双阳极电化学氢化物发生-原子荧光光谱法测定Ⅰ型牙髓失活材料中的砷形态

将自制的双阳极电化学氢化物发生器作为离子色谱与原子荧光光谱的联用接口,建立了离子色谱-双阳极电化学氢化物发生-原子荧光光谱法在线分析砷形态系统.最佳实验条件为淋洗液6.0 mmol/L NH4H2PO4(pH 6.20),电解液0.40 mol/L H2SO4,电解液流量为阳极4.0 mL/min,阴极 1.5 mL/min,电解电流密度0.50 A/cm.2,载气流量300 mL/min,屏蔽气流量500 mL/min,氢气流量80 mL/min.在优化的实验条件下,As(Ⅲ)、DMA、MMA的线性范围为5～200 μg/L、As(Ⅴ)的线性范围为10～200 μg/L,As(Ⅲ)、DMA、MMA和As(Ⅴ)检出限分别为3.04、4.27、3.97和9.30 μg/L(信噪比S/N=3).50 μg/L的As(Ⅲ)、DMA、MMA和As(Ⅴ)混合标准溶液平行进样7次,得到的色谱峰面积的相对标准偏差(RSD)分别为415%、3.08%、519%和3.62%.将该方法用于牙髓失活材料中的砷形态分析.     

蒸馏-催化极谱法测定复杂物料中微量砷

提出了用催化极谱法测定复杂物料中微量砷的含量。选择测定的溶液介质中含碲(Ⅳ)硫酸溶液5mL和150g.L-1碘化钾溶液5mL。仪器扫描速率为250mV.s-1,并采用二阶导数测定。试样(0.01～1.0g)用氯酸钾0.5g、氢氟酸5滴、硝酸5～10mL溶解,用蒸馏法分离其中的砷。砷的质量浓度在0.4mg·L-1以内与相应的峰电流呈线性关系。按此方法测定了12个矿样中砷含量,其测定值与已知值相符。方法的回收率在97%～100%之间,相对标准偏差(n=6)在2.3%～7.2%之间。     

Small-angle X-ray scattering on solutions of carboxymethylcellulose and bovine serum albumin

The existence of attractive interaction between CMC and BSA was evidenced in solution at pH higher than the protein isoelectric point by means of SAXS. Mixtures of BSA at 10 x 10(-3) g . mL(-1) and CMC at the concentration range of 1 x 10(-3) g . mL(-1) to 10 x 10(-3) g . mL(-1) were investigated. Upturns in the very low q range revealed the presence of aggregates when the CMC concentration was higher than 2 x 10(-3) g . mL(-1). The comparison between the calculated form factor with the experimental curves at intermediate and long q values indicated that the BSA molecules keep their native form in mixtures with CMC concentrations lower than 5 x 10(-3) g . mL(-1). Therefore, for CMC concentrations higher than 2 x 10(-3) g . mL(-1) the mixtures start to present aggregates and free BSA molecules coexisting in solution.     

Controllable Hydrolysis Performance of MgLi Alloys and Their Hydrides

Theoretically, the hydrolysis of MgLi and MgH₂−LiH can produce 9.6 and 17.5 wt.% hydrogen (water is not included in the calculation), respectively. The ball-milling method is commonly used to refine the particle size and thus may improve hydrolysis kinetics. However, Mg and Li will be easily agglomerated, which means that direct ball-milling could not refine MgLi. In this work, we introduced 10 wt.% expanded graphite into the ball-milling process to synthesize refined MgLi alloy samples. Further studies showed that MgLi-10 wt.% expanded graphite can produce 966 mL/g hydrogen within 3 min in 0.5 M MgCl₂ solution. The MgLi hydrides were synthesized by reactive ball milling under 3 MPa H₂ and their hydrolysis performance was investigated. Moreover, the sawed powder was milled in 3 MPa H₂ for 6 h and then hydrogenated in 3 MPa H₂ at 380 °C; it can produce 1542 and 1773 mL/g (15.8 wt.%) hydrogen in 5 and 30 min with mild kinetics, respectively, and the activation energy of the hydrolysis reaction is 24.6 kJ/mol in 1 M MgCl₂ solution. The findings here open a new avenue to the development of refined MgLi alloys and hydrides for hydrogen generation through a controllable hydrolysis process.     

Simultaneous determination of N,N-dimethylaniline and phenol in wastewater by high-performance liquid chromatography with chemiluminescence detection.

A method using HPLC-CL linkage was developed for simultaneous determination of N,N-dimethylaniline and phenol in wastewater, based on the strong sensitive chemiluminescence of the luminol-K3Fe(CN)6 systems in alkaline medium. The separation was carried out on a Hypersil ODS column with a mobile phase of ethanol-0.01% triethylamine (2:1, v/v). The linear ranges for N,N-dimethylaniline determinations were 2.0 x 10(-7) - 2.5 x 10(-5) g/mL and 4.0 x 10(-5) - 1.5 x 10(-4) g/mL with a detection limit (3sigma) of 1.20 x 10(-8) g/mL; the relative standard deviation (3sigma) for 5.0 x 10(-6) g/mL N,N-dimethylaniline was 1.4% (n = 6). The range for phenol was from 5.1 x 10(-7) to 1.3 x 10(-4) g/mL, and a detection limit (3sigma) of 2.5 x 10(-8) g/mL could be obtained. The method can be useful for the determination of N,N-dimethylaniline and phenol in some environmental samples.     

Molecularly imprinted solid-phase extraction for the selective HPLC determination of ractopamine in pig urine

A method was developed for the determination of ractopamine in pig urine using molecularly imprinted solid-phase extraction (MISPE) as the sample clean-up technique combined with high-performance liquid chromatography. The molecularly imprinted polymer (MIP) was synthesized in acetonitrile-triethylamine system using ractopamine (RAC) as the template and acrylamide as the monomer. The binding capacity of the polymer toward RAC was found to be about 2.57 mg of ractopamine/g of polymer. The optimal procedures for MISPE consisted of conditioning with 3 mL methanol, equilibrating with 3 mL of water, loading volume of <10 mL of aqueous sample (pH 7), washing with 3 mL water and 3 mL methanol, and eluting with 5 mL of 5% ammonia in methanol. In the four spiked samples with the levels of 0.01, 0.1, 1.0 and 5.0 μg/mL, the mean recoveries of analyte on the MIP were higher than 90% with relative standard deviation <10%, and significant differences between imprinted and non-imprinted materials were observed. The MIP selectivity was evaluated by checking 11 drugs with similar and different molecular structures to that of RAC. The characteristics of three-dimensional cavities and hydrogen bond interaction were regarded as the main factors that dominated the retention of RAC on the MISPE cartridge.     

Determination of the rate of reaction between potassium iodide and potassium peroxodisulphate with the econoburette: a green chemistry and microscale titrations

Measurement for a rate of reaction for about 30?min at a 5?min interval between KI and K₂S₂O₈ aqueous solutions with conventional burette in industries and academics consumes about 3.375?g K₂S₂O₈/250?mL?:?4.15?g KI/250?mL?:?11.6?mL (CH₃COOH, glacial)/100?mL?:?1?g starch/10?mL?:?0.62?g Na₂S₂O₃ (sodium thiosulphate)/250?mL?:?50?mL ice cold water. The number after the oblique in mL depicts an amount of aqueous solution where the amounts of chemicals in grams are dissolved. Similar determinations with econoburette reduced their amounts in 0.0675?g K₂S₂O₈/5?mL?:?0.083?g KI/5?mL:?0.5?mL (CH₃COOH, glacial)/5?mL?:?0.05?g starch/0.5?mL?:?0.025?g Na₂S₂O₃/2?mL?:?2.5?mL ice cold water. The reduction in amounts is about 50 times, and similarly the time and operational efforts are reduced in the same proportion. The econoburette is a ‘green chemistry’ instrument which performs valuable titration with microlitre of substances. The micro level amount of titer and titrant consumed less time in performing a volumetric tititration and also prevented much use of materials. In general, after titration a significant quantity of indicators, additives, titer and titrant are consumed and drained out in a sink with the possibility of causing pollution. The econoburette reduces such wastage of materials by up to 90%, with high accuracy in results. The rate constant k?=?0.0431?sec^?1?L^–1?mol^?1 remained fairly constant for successive measurements with time but with the conventional burette larger deviations were noted at 298.15 Kelvin temperature.     

液相色谱法测定婴幼儿食品包装材料中的脂肪胺

采用新型气流吹扫-微注射器萃取( GP-MSE)技术,用酸化甲醇为提取溶剂,对食品包装材料中脂肪胺进行了提取和富集。以10-乙基-吖啶酮-2-磺酰氯( EASC)为荧光试剂,在60℃、pH 10的条件下,对脂肪胺进行柱前荧光衍生, Hypersil GOLD柱分离,荧光检测的激发波长(λex )和发射波长(λem )分别为262 nm和430 nm。12种脂肪胺检出限为0.4~0.6μg/kg,定量限为1.2~2.1μg/kg,在2.0~2000μg/L浓度范围内,线性相关系数均大于0.998。本方法具有快速、准确、灵敏的特点,用于婴幼儿食品包装材料分析,结果令人满意。     

单链和寡链等规聚苯乙烯聚集体的结晶行为

自1960年Hoffman等提出聚合物结晶成核理论以来,人们对聚合物结晶生长速率、片晶的侧向尺寸随过冷度的变化等现象成功地进行了理论描述．1997年,Hoffman等对聚合物结晶成核理论进行修正,将de Gennes的聚合物“蛇行”概念。引入表面成核理论,通过对单根分子链从过冷熔体“卷绕”到晶体前沿所需的时间进行估算,其结果远远低于Flory预言时间约3～5个数量级,据此,Hoff-man认为,在聚合物结晶过程中,分子链在强迫稳态下的“蛇行”运动有足够的时间解缠结和结晶。     

Large volume sample stacking with EOF and sweeping in CE for determination of common preservatives in cosmetic products by chemometric experimental design

This study proposes a capillary electrophoresis method incorporating large volume sample stacking, EOF and sweeping for detection of common preservatives used in cosmetic products. The method was developed using chemometric experimental design (fractional factorial design and central composite design) to determine multiple separation variables by efficient steps. The samples were loaded by hydrodynamic injection (10 psi, 90 s), and separated by phosphate buffer (50 mM, pH 3) containing 30% methanol and 80 mM SDS at -20 kV. During method validation, calibration curves were found to be linear over a range of 5-100 μg/mL for butyl paraben and isobutyl paraben; 0.05-10 μg/mL for ethyl paraben; 0.2-50 μg/mL for dehydroacetic acid; 0.5-70 μg/mL for methyl paraben; 5-350 μg/mL for sorbic acid; 0.02-450 μg/mL for p-hydroxybenzoic acid and 0.05-10 μg/mL for salicylic acid and benzoic acid. The analytes were analysed simultaneously and their detection limits (S/N = 3) were down to 0.005-2 μg/mL. The analysis method was successfully used for detection of preservatives used in commercial cosmetics.