Experimental Design Optimization of Solid‐Phase Microextraction Conditions for the Determination of Heterocyclic Aromatic Amines by High‐Performance Liquid Chromatography

Abstract

Solid‐phase microextraction, using Carbowax‐Templated Resin fiber, coupled with high performance liquid chromatography ultra violet/diode array detector (HPLC‐UV/DAD) has been optimized for the determination of the heterocyclic aromatic amines (HAs). Three variables (absorption time, soaking time, and desorption time) were considered as factors in the optimization process. Interactions between analytical factors and their optimal levels were investigated using two level factorial and Doehlert matrix designs. Absorption time and soaking time were significant variables, and 15 min for each one of the variables was chosen for the best response. The optimized procedure allowed the determination of HAs with detection limits that ranged from 1.58 to 16.8 ng/L (except PhIP: 23.8 ng/L). The reproducibility of the method (n=5), expressed as relative standard deviation was between 2.21% and 28.3%. The method was applied to the analysis of a meat extract sample and the range of recoveries for the amines was 64.14%–112.72%.     

Determination of less polar heterocyclic amines in meat extracts: fast sample preparation method using solid-phase microextraction prior to high-performance liquid chromatography-fluorescence quantification

A procedure for the determination of less polar heterocyclic amines in meat extracts using solid phase microextraction (SPME) coupled to high-performance liquid chromatography (HPLC) with fluorescence detection is presented. Analytes were first extracted from the samples using methanol/NaOH by an ultrasound-assisted method, and then concentrated on a Carbowax-templated resin (CW-TPR) SPME fiber. The extraction conditions such as extractant mixture composition, extraction time and extractions number, were optimized and the need of an extract freezing step previous to SPME is discussed. The detection limits under optimal conditions are in the range of 0.28-1.1 ng g⁻¹. The method was applied to the determination of less polar heterocyclic amines in four commercial meat extracts. Recovery values obtained are higher than 60% for the majority of amines.     

Determination of chlorophenols by solid-phase microextraction and liquid chromatography with electrochemical detection

A solid-phase microextraction method has been developed for the determination of 19 chlorophenols (CPs) in environmental samples. The analytical procedure involves direct sampling of CPs from water using solid-phase microextraction (SPME) and determination by liquid chromatography with electrochemical detection (LC-ED). Three kinds of fibre [50 microm carbowax-templated resin (CW-TPR), 60 microm polydimethylsiloxane-divinylbenzene (PDMS-DVB) and 85 microm polyacrylate (PA)] were evaluated for the analysis of CPs. Of these fibres, CW-TPR is the most suitable for the determination of CPs in water. Optimal conditions for both desorption and absorption SPME processes, such as composition of the desorption solvent (water-acetonitrile-methanol, 20:30:50) and desorption time (5 min), extraction time (50 min) and temperature (40 degrees C) as well as pH (3.5) and ionic strength (6 g NaCl) were established. The precision of the SPME-LC-ED method gave relative standard deviations (RSDs) of between 4 and 11%. The method was linear over three to four orders of magnitude and the detection limits, from 3 to 8 ng l(-1), were lower than the European Community legislation limits for drinking water. The method was applied to the analysis of CPs in drinking water and wood samples.     

Determination of hydroxyaromatic compounds in water by solid-phase microextraction coupled to high-performance liquid chromatography

Solid-phase microextraction (SPME) coupled with high-performance liquid chromatography (HPLC) for the analysis of hydroxyaromatic compounds is described. Three kinds of fibers [50 microns carbowax-templated resin (CW-TPR), 60 microns polydimethylsiloxane-divinylbenzene (PDMS-DVB) and 85 microns polyacrylate (PA) fibers] were evaluated. CW-TPR and PDMS-DVB were selected for further study. The parameters of the desorption procedure (such as desorption mode, the composition of the solvent for desorption and the duration of fiber soaking) were studied and optimized. The effect of the structure and physical properties of analytes, carryover, duration of absorption, temperature of absorption, pH and ionic strength of samples were also investigated. The method was applied to environmental samples (lake water) using a simple calibration curve.     

肉类食品中杂环胺检测的样品前处理及分析方法的研究进展

杂环胺是畜禽、鱼肉等食品在高温烹饪过程中生成的一类致癌、致突变化合物,高效、高选择性的样品前处理方法和高灵敏的分析方法是食品中痕量杂环胺分析检测的关键。本文综述了近年来溶剂萃取、固相萃取和固相微萃取等样品前处理方法,以及液相色谱、液相色谱-质谱等分析方法在食品中痕量杂环胺检测中的应用,结合现有研究对其发展趋势进行了展望。共引用文献51篇。     

Cyclodextrin‐functionalized reduced graphene oxide as a fiber coating material for the solid‐phase microextraction of some volatile aromatic compounds

A novel solid phase microextraction fiber was prepared for the first time by using a sol–gel technique with hydroxypropyl‐β‐cyclodextrin‐functionalized reduced graphene oxide as the fiber coating material. The results verified that the β‐cyclodextrin was successfully grafted onto the surface of reduced graphene oxide and the coating possessed a uniform folded and wrinkled structure. The performance of the solid phase microextraction fiber was evaluated by using it to extract nine volatile aromatic compounds from water samples before determination with gas chromatography and flame ionization detection. Some important experimental parameters that could affect the extraction efficiency such as the extraction time, extraction temperature, desorption temperature, desorption time, the volume of water sample solution, stirring rate, as well as ionic strength were optimized. The new method was validated to be effective for the trace analysis of some volatile aromatic compounds, with the limits of detection ranging from 2.0 to 8.0 ng/L. Single fiber repeatability and fiber‐to‐fiber reproducibility were in the range of 2.5–9.4 and 5.4–12.9%, respectively. The developed method was successfully applied to the analysis of three different water samples, and the recoveries of the method were in the range from 77.9 to 113.6% at spiking levels of 10, 100, and 1000 ng/L, respectively.     

Determination of aromatic amines from textiles using dispersive liquid–liquid microextraction

A dispersive liquid–liquid microextraction procedure coupled with GC‐MS is described for preconcentration and determination of banned aromatic amines from textile samples. Experimental conditions affecting the microextraction procedure were optimized. A mixture of 30 μL chlorobenzene (extraction solvent) and 800 μL ACN (disperser solvent), 5 min extraction time, and 5 mL aqueous sample volume were chosen for the best extraction efficiency by the proposed procedure. Satisfactory linearity (with correlation coefficients >0.9962) and repeatability (<9.78%) were obtained for all 20 aromatic amines; detection limits attained were much lower than the standardized liquid–liquid method. The proposed method has advantages of being quicker and easier to operate, and lower consumption of organic solvent.     

Ionic liquids as desorption solvents and memory effect suppressors in heterocyclic aromatic amines determination by SPME–HPLC fluorescence

The beneficial effects of 1-butyl-3-methylimidazolium tetrafluoroborate (BMIm-BF₄) ionic liquid (IL) as mobile phase additive, desorption solvent, and memory effect suppressor in solid-phase microextraction (SPME)–high-performance liquid chromatography with fluorescence detection for the determination of six heterocyclic aromatic amines have been evaluated for the first time. Several chromatographic parameters have been evaluated in the presence or absence of IL or using triethylamine as the most common mobile phase additive, with a Nova-Pak® C18 stationary phase. This IL was found to be clearly superior to triethylamine for efficiency as well as peak shape enhancement and sensitivity increase. SPME was chosen because it is faster than conventional extraction techniques and allowed us to minimize the use of organic solvents. However, memory effect may become a problem when a high-sensitivity detector is used. The appropriate conditions for the desorption step and to eliminate the memory effect involving BMIm-BF₄ were established and optimized. The method was applied for the determination of these compounds in commercial meat extracts.     

Solid-phase microextraction with micellar desorption and HPLC-fluorescence detection for the analysis of fluoroquinolones residues in water samples

A sensitive and useful method based on solid-phase microextraction with micellar desorption (SPME-MD) coupled to HPLC with fluorescence detection was developed for the determination of five fluoroquinolones (levofloxacin, norfloxacin, ciprofloxacin, enrofloxacin, and sarafloxacin) in environmental water matrices. The SPME extraction efficiency was optimized with regard to time, temperature, pH, and ionic strength using a CW-TPR fiber. A detailed study about the optimum conditions for micellar desorption (surfactant type, concentration, and desorption time) were made. Among different surfactants studied, Polyoxyethylene 10 lauryl ether showed the best responses to extract fluoroquinolones using SPME-MD. Relative standard deviations of the developed method were below 9%. Limits of detection and quantification were between 0.01–0.2 and 0.03–0.6 ng mL⁻¹, respectively. The recoveries achieved for all five compounds were in the 81–116% range. The proposed method was compared using conventional desorbing agent as methanol. Finally, the SPME-MD methodology was applied to the determination of these target analytes in several environmental liquid samples, including seawater, groundwater, and wastewater samples with excellent results.     

用于固相微萃取的乙烯基开链冠醚复合涂层的研制

固相微萃取 (SPME)是一种新型的样品预处理技术 [1] ,其核心是 SPME装置中萃取头上的固相涂层 .目前商用 SPME涂层的种类较少 ,热稳定性较差 (推荐使用温度 2 0 0～ 2 80℃ ) ,使用寿命较短(40～ 1 0 0次 ) ,价格偏高 ,限制了其推广应用 .因此发展高选择性、高稳定性和高效的固     

固相微萃取法在禁用偶氮染料检测中的应用初探

将固相微萃取技术应用于出口染色纺织品及皮革制品中禁用偶氮染料检验,偶染料经连二亚硫酸钠还原成芳胺后,用固相微萃取技术萃取富集后,用ＧＣ－ＭＳ分析。实验了萃取方式、萃取纤维、pＨ值、浓度、温度、萃取时间及色谱条件等因素对萃取与测定的影响。     

Application of micro‐solid‐phase extraction for the on‐site extraction of heterocyclic aromatic amines in seawater

An efficient on‐site extraction technique to determine carcinogenic heterocyclic aromatic amines in seawater has been reported. A micro‐solid‐phase extraction device placed inside a portable battery‐operated pump was used for the on‐site extraction of seawater samples. Before on‐site applications, parameters that influence the extraction efficiency (extraction time, type of sorbent materials, suitable desorption solvent, desorption time, and sample volume) were investigated and optimized in the laboratory. The developed method was then used for the on‐site sampling of heterocyclic aromatic amines determination in seawater samples close to distillation plant. Once the on‐site extraction completed, the small extraction device with the analytes was brought back to the laboratory for analysis using high‐performance liquid chromatography with fluorescence detection. Based on the optimized conditions, the calibration curves were linear over the concentration range of 0.05–20 μg/L with correlation coefficients up to 0.996. The limits of detection were 0.004–0.026 μg/L, and the reproducibility values were between 1.3 and 7.5%. To evaluate the extraction efficiency, a comparison was made with conventional solid‐phase extraction and it was applied to various fortified real seawater samples. The average relative recoveries obtained from the spiked seawater samples varied in the range 79.9–95.2%.     

Highly porous silica-polyaniline nanocomposite as a novel solid-phase microextraction fiber coating

A highly porous fiber-coated SBA-15/polyaniline material was prepared for solid-phase microextraction (SPME). The SBA-15/polyaniline nanocomposite was synthesized via chemical polymerization. The prepared SBA-15/polyaniline particles were analyzed by scanning electron microscopy analysis. The prepared nanomaterial was immobilized onto a stainless steel wire for fabrication of the SPME fiber. The fiber was evaluated for the extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions in combination with gas chromatography-mass spectrometry (GC-MS). In optimum conditions (extraction temperature 60°C, extraction time 40 min, ionic strength 20%, stirring rate: 500 rpm, desorption temperature 260°C, desorption time 2 min), the repeatability for one fiber (n=3), expressed as relative standard deviation (RSD%), was between 5.3 and 8.6% for the test compounds. For deionized water, spiked with selected PAHs, the detection limits for the studied compounds were between 2 and 20 pg/mL.     

液相微萃取-毛细管电泳联用对汗液基质中4种芳香胺的同时测定

采用纤维膜三相液相微萃取(HF-LLLME)技术,对汗液基质中的苯胺、邻甲苯胺、对氯苯胺、对硝基苯胺进行了分离富集。以正辛醇为有机相,在供体相pH为9.0,NaCl质量浓度为200g/L,接收相pH为1.0,萃取时间为60min的条件下,4种芳香胺的富集倍数为410～1250倍。将接收相直接进行毛细管电泳(CE)测定,样品相中4种芳香胺的质量浓度在10～100μg/L范围内与电泳峰面积呈良好线性,相关系数均大于0.992,4种芳香胺的检出限为1～10μg/L。运用该法对偶氮染料汗液环境下光致降解过程中产生的苯胺进行测定,回收率为91%～93%,结果满意。     

Graphene oxide decorated with silver nanoparticles as a coating on a stainless‐steel fiber for solid‐phase microextraction

A novel graphene oxide decorated with silver nanoparticles coating on a stainless‐steel fiber for solid‐phase microextraction was prepared. Scanning electron microscopy and X‐ray photoelectron spectroscopy were used to characterize the coating surface and showed that silver nanoparticles were dispersed on the wrinkled graphene oxide surface. Coupled to gas chromatography with flame ionization detection, the extraction abilities of the fiber for polycyclic aromatic hydrocarbons were examined in the headspace solid‐phase microextraction mode. The extraction parameters including adsorption time, adsorption temperature, salt concentration, desorption time and desorption temperature were investigated. Under the optimized condition, wide linearity with low limits of detection from 2 to 10 ng/L was obtained. The relative standard deviations for single‐fiber repeatability and fiber‐to‐fiber reproducibility were less than 10.6 and 17.5%, respectively. The enrichment factors were from 1712.5 to 4503.7, showing the fiber has good extraction abilities. Moreover, the fiber exhibited a good stability and could be reused for more than 120 times. The established method was also applied for determination of polycyclic aromatic hydrocarbons in two real water samples and the recoveries of analytes ranged from 84.4–116.3% with relative standard deviations less than 16.2%.     

Solid-phase microextraction of monocyclic aromatic amines using novel fibers coated with crown ether.

Three solid-phase microextraction (SPME) fibers prepared by the sol-gel method, containing hydroxydibenzo-14-crown-4 (OH-DB14C4), dihydroxy-substituted saturated urushiol crown ether (DHSU14C4) and 3,5-dibutyl-unsymmetry-dibenzo-14-crown-4-dihydroxy crown ether (DBUD14C4), respectively, were evaluated for the determination of aromatic amine (aniline, m-toluidine, N,N-diethylaniline, N-ethyl-m-toluidine, 3,4-dimethylaniline). The sol-gel-derived hydroxy-dibenzo14-crown-4-coated fiber has the best affinity for several aniline derivatives. Optimization was carried out for the determination of aromatic amines with SPME fibers. The linearity was from 0.11 to 29 microg/ml and detection limits varied from 0.17 to 0.98 ng/ml. Relative standard deviation (n=5) was found to be 3.23-6.20%. The coating proved to be very stable at high temperature (to 340 degrees C) and in different solvents (organic and inorganic). The method was applied to the determination of aromatic amines in wastewater samples from a pharmaceutical factory.     

Comparison of three different solid-phase microextraction fibres for analysis of essential oils in yacon (Smallanthus sonchifolius) leaves

A headspace solid-phase microextraction (HS-SPME) procedure based on three commercialised fibers (100 microm polydimethylsiloxane, 65 microm polydimethylsiloxane-divinylbenzene and 50/30 microm divinylbenzene-Carboxen-polydimethylsiloxane) is presented for the determination of a selected essential oils in dried leaves of yacon (Smallanthus sonchifolius). The extraction performances of these compounds were compared using fibers with one, two and three coatings. The optimal experimental procedures for the adsorption and desorption of target compounds were determined. Significant parameters affecting sorption process such as sample weight, sorption and desorption time and temperature were optimised and discussed. Finally, the optimised procedures were applied successfully for the determination of these compounds in various yacon species. The relative concentration factors of three characteristic components of yacon were measured for relative evaluation of the fiber efficiency. Main essential oils were isolated from dried yacon leaves by appropriate solid-phase microextraction fiber and semi-quantitative analysis of the target volatiles was conducted by gas chromatography-flame ionisation detection (GC-FID) using a capillary column. Three compounds--beta-pinene, caryophylene and y-cadinene were found as the predominant essential oils. Its relative content was important for specification of yacon varieties. Solid-phase microextraction in combination with gas chromatography enabled a rapid and simple determination of relative content of essential oils in yacon.     

MultiSimplex optimisation of the solid-phase microextraction-gas chromatographic-mass spectrometric determination of polycyclic aromatic hydrocarbons,polychlorinated biphenyls and phthalates from water samples

Solid-phase microextraction coupled to GC-MS was optimised for the determination of polycyclic aromatic hydrocarbons (PAHs), phthalate esters and polychlorinated biphenyls (PCBs) in water samples. A 30-microm polydimethylsiloxane fiber was immersed in a 30-ml water sample that contained the analytes of interest (PAHs, PCBs and phthalate esters) and the variables studied were extraction time (15-60 min), extraction temperature (30-90 degrees C), desorption time (1-5 min), desorption temperature (220-270 degrees C) and the addition of sodium chloride (0-9 g). The MultiSimplex programme based on the simplex algorithm was used to establish the optimal conditions. MultiSimplex allowed the simultaneous study of the variables mentioned above and considered the answers of all types of compounds studied in this work. Thus, the optimal conditions obtained allowed the simultaneous determination of PAHs, phthalate esters and PCBs. Furthermore, the accuracy and repeatability of the developed method were calculated from water samples spiked at known concentrations of the analytes. Finally, the optimised method was used to analyse water samples from different sampling points of the Urdaibai and Nerbioi-Ibaizabal estuaries (Biscay, Spain).     

Layer‐by‐layer self‐assembly of a novel covalent organic frameworks microextraction coating for analyzing polycyclic aromatic hydrocarbons from aqueous solutions via gas chromatography

In this study, a new covalent organic framework, consisting of tetra(4‐aminophenyl)porphyrin and tris(4‐formyl phenyl)amine, was layer‐by‐layer immobilized on stainless‐steel wire as a coating for microextraction. The fabrication process was easy and controllable under mild conditions. The as‐grown fiber was applied to extract polycyclic aromatic hydrocarbons in aqueous solution via head‐space solid‐phase microextraction. Furthermore, it was analyzed by gas chromatography with a flame ionization detector. A wide linear range (0.1–50 µg/L), low limits of detection (0.006–0.024 µg/L, signal‐to‐noise ratio = 3), good repeatability (intra‐fiber, n = 6, 3.1–8.50%), and reproducibility (fiber to fiber; n = 3, 5.79–9.98%), expressed as relative standard deviations, demonstrate the applicability of the newly developed coating. This new material was successfully utilized in real sample extraction with a satisfactory result. Potential parameters affecting the extraction efficiency, including extraction temperature and extraction time, salt concentration, agitation speed, sample volume, desorption temperature, and time, were also optimized and discussed.     

Selective solid-phase microextraction of polycyclic aromatic hydrocarbons in water based on oriented phosphorus-containing titanium oxide nanofibers grown on titanium support prior to high-performance liquid chromatography with ultraviolet detection

A novel solid-phase microextraction coating of phosphorous-containing titanium oxide composite was developed using titanium fiber as a support and a titanium source by hydrothermal oxidation in a phosphoric acid solution containing hydrogen peroxide. The morphology of the fiber coatings was controlled by the conditions of the hydrothermal oxidation reaction. The oriented nanofiber coating was employed to extract several types of representative aromatic analytes. The experimental results demonstrated that the as-prepared fiber exhibited excellent extraction efficiency toward polycyclic aromatic hydrocarbons. Combined with high-performance liquid chromatography with ultraviolet detection, main extraction conditions were optimized, including pH, ionic strength, extraction temperature, stirring rate, extraction time and desorption time. The established method presented good linearity from 0.05 to 200 μg/L with limit of detection ranging from 0.012 to 0.126 μg/L. This convenient and green procedure was suitable for the selective extraction and determination of typical polycyclic aromatic hydrocarbons in environmental water samples. The relative recoveries of 85.8–112% were obtained for the determination of target polycyclic aromatic hydrocarbons in water samples spiked with 5.0 and 15.0 μg/L. Moreover, the as-prepared fiber showed at least 210 extraction/desorption cycles due to its high mechanical and chemical stability.