甲醇在电解银催化剂表面上的氧化

＃ 用程序升温反应谱(TPRS)研究了甲醇在电解银工业催化剂表面上的氧化反应。结果表明:除少量H_2O和微量CO_3外,纯净的银表面不吸附CH_3OH,D_2等气体,当银表面预吸附氧后,显著增强了上述气体的吸附和反应。在程序升温过程中,甲醇与预吸附的氧发生表面反应,分别在温度400,500和630K时给出三组分开的产物群。由产物的峰形、峰温和动力学参数得出:第一、第三组产物群的控速步骤是两个不同的表面反应;第二组产物群的控速步骤为反应产物的表面脱附。     

聚对羟基苯乙烯单体的中间体——对特丁氧酰氧基苯乙烯合成方法的改进

通过改进反应溶剂,用Wittig反应合成了对特丁氧酰氧基苯乙烯,以中性Al2O3为固定相,正己烷为流动相,采用普通液相色谱分离提纯了混合产物,改进简化了分离方法。结果表明,所得目标产物对特丁氧酰氧基苯乙烯纯度达99%以上,产率为60%~70%,中间产物对特丁氧酰氧基苯甲醛可以定量合成,反应的副产物主要是三苯基氧化膦。对目标产物、中间产物和一些反应副产物进行了红外和核磁共振分析。     

拟肾上腺素药盐酸甲氧明的绿色合成

以对苯二酚为原料经羟基的甲基化、傅克酰基化、肟化、肟基还原、酮胺氢化5步反应合成了盐酸甲氧明, 中间体和目标产物经核磁共振氢谱、红外光谱及元素分析仪确证了其化学结构, 总收率为37.6%. 与传统盐酸甲氧明工艺相比, 该工艺反应条件温和、简便、经济、产率高及对环境友好.     

β-氯乙基乙烯基醚与柠康酸酐的共聚合反应的研究

衣文报导了用偶氮二异丁腈为引发剂,苯或甲苯为反应介质,β-氯乙基乙烯基醚与柠康酸酐共聚合反应的研究.红外光谱及核磁共振谱证明反应产物为共聚物,较详细地研究了反应条件对单体转化率、产物分子量及分子量分布的影响。     

SmMO_3(M=Mn、Fe)上氧物种反应性能的TDS和TPRS研究

用热脱附谱法(TDS)和程序升温反应谱法(TPRS),以O_2和CO为反应分子探针,研究了钙钛矿型氧化物SmMnO_3和SmFeO_3表面上氧物种的反应性能,并得出了CO在这两种氧化物上的氧化反应符合Langmuir—Hinshelwood机理。     

乙二醇在电解银表面的氧化

用超高真空程序升温反应谱和瞬时应答方法研究了乙二醇在电解银表面的氧化，实验表明，室温下乙二醇吸附在电解银表面，并在３４３Ｋ分解给出一组产物群，预吸附氧与乙二醇反应时，在３４３Ｋ，４３３Ｋ和６１２Ｋ处给出三组产物群，它们分别对应于不同的表面反应，并给出了电解银催化乙二醇制乙二醛的活性结果。     

硅胶固载聚4-乙烯吡啶-Cu(Ⅱ)配合物催化分子氧氧化乙苯的性能研究

以固载于微米级硅胶表面的聚4-乙烯吡啶-铜(Ⅱ)配合物(P4VP-Cu(Ⅱ)/SiO2)为催化剂,以分子氧为氧化剂,在常压下实施了将乙苯氧化为苯乙酮的催化氧化反应;用红外光谱、紫外光谱及液相色谱对产物的化学结构进行了表征;重点研究了催化剂的催化性能,以及各种条件(温度、催化剂性质、催化剂用量等)对催化氧化反应的影响;并分析了催化氧化反应的机理.研究结果表明,固载于硅胶表面的聚4-乙烯吡啶-Cu(Ⅱ)配合物能有效地活化分子氧,显著地催化氧化乙苯为苯乙酮的反应过程;该催化剂具有优良的催化活性与选择性,于130℃常压下通氧气反应10h,可使约60%的乙苯转化为苯乙酮,另一氧化产物α-甲基苄醇的含量则极少.另外,该催化剂具有较好的重复使用稳定性.     

吡咯烷-3-羧酸甲酯的合成

以氯甲基三甲基硅烷、苄胺、丙烯酸甲酯为起始原料,经过取代、甲氧甲基化、合环,最后脱保护,得到标题化合物,总收率为86.1%。由核磁共振氢谱对产物进行了结构表征。本方法具有反应条件温和、产率高、易于纯化的特点,为目标化合物的合成提供了新途径。     

卤素功能化靛红的合成及其烃基化、还原和酰基化反应研究

报道了以4-卤代苯胺为原料经Sandmeyer反应得到卤素功能化靛红3a~3c,进一步烃基化反应得到氮上烃基化产物4a~4o.4a~4o用水合肼还原得到了吲哚酮产物5a~5o,5a~5o用乙酸酐作酰化试剂在4-二甲氨基吡啶为催化剂的条件下反应生成2,3位酰基化的中间体,此中间体不经提纯,而使酯基在四氢呋喃为溶剂、5%氢氧化钠为碱的条件下水解得到3位酰基化产物6a~6o.部分化合物未见文献报道,其结构经红外光谱、质谱、核磁氢谱(碳谱)和元素分析确认.     

N-烯基硝酮分子内环加成反应区域选择性的理论研究I. N-3-丁烯基硝酮分子内环加成反应的区域专一性

n-烯基硝酮的分子内环加成反应可能得到氧桥和碳桥的两种产物, 但N-3-丁烯基硝酮却只有单一的氧桥产物, 已被用来合成一系列新的区域专一性人化合物。弄清此反应机理是很有意义的。本文用过渡状理论和AM1方法进行研究, 结果表明,虽然存在得到两种产物的平行反应, 但由于这两个反应的速率常数之比很大, 基本上只得到单一的氧桥产物。生成氧桥产物的反应活化焓比较小, 活化熵比较大。活化熵对反应速率常数比值的贡献是不可忽略的。     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

室温氧化还原反应制备AgCuSe三元纳米棒

AgCuSe nanorods were prepared at room temperature by a redox reaction. The as-prepared product was characterized by X-ray powder diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy.X-ray powder diffraction shows that the as-prepared product is the tetragonal phase of AgCuSe. Transmission electron microscopy shows that the sample consists of nanorods with a diameter varying from 5 nm to 20 nm and a length varying from 200 nm to 600 nm. X-ray photoelectron spectroscopy shows that the purity of the sample is high. The formation mechanism of AgCuSe and the growth mechanism of AgCuSe nanorods were discussed.Thermodynamic calulations show that the final product in the synthetic system is pure AgCuSe. The solvent ethylenediamine did not only acts a didentate ligand to form relatively state Ag + and Cu + complexes, but also dissolved Se and enhanced the reactivity of Se. It played an important role in controlling the nucleation and growth of AgCuSe nanorods.     

线性反馈抑制螺旋波

A class of excitable media described by the Fitzhugh-Nagumo equation is investigated. Based on the stable and self adaptive theory, the error between the systems grid variables and the standard sampling of the periodical signal or constant signal was feed back into the system both globally and locally. When the controller was then shut off, automatically, the whole system became homogeneous. Additionally, the scheme was tested under noisy conditions. The numerical simulations results demonstrate its effectiveness. The system reached a homogeneous state and a spiral wave was converted into a target wave, resulting in a wonderful pattern emerging using a different controller. The scheme proved robust in resisting the effects of noise.     

Synthesis and characterization of inorganic solid electrolytes of Li2O-SiO2-P2O5 and Li2O-TiO2-SiO2-P2O5 systems

The lithium-ion-conducting inorganic solid electrolytes in the oxide systems Li₂O-SiO₂-P₂O₅ and Li₂O-TiO₂-SiO₂-P₂O₅ were prepared by the solid-state reaction, and the electrolyte pellet made by cold-pressing method had diameter of 13 mm and was about 1 mm thick. Phase identification and surface morphology of the products were carried out by X-ray diffraction and scanning electron microscopy. Ionic conductivity of the pellets was investigated through ac impedance. The results show that the adding of other cations can improve the ionic conductivity of the solid electrolyte, and the sintering temperature and duration can influence the ionic conductivity. The maximum ionic conductivity in the samples is 9.9 × 10⁻⁴ S/cm in the Li₂O-TiO₂-SiO₂-P₂O₅ system. Original Russian Text ? W. Li, M. Wang, Z.H. Li, X.F. Shang, H. Wang, Y.W. Wang, Y.B. Xu, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 11, pp. 1341–1345.     

酞菁染料的金属化和溴化与光物理影响的研究

以α位(2,4-二特戊基)苯氧基邻苯二腈作为环合前体,制备了多种金属酞菁,产物经元素分析、紫外、红外、核磁氢谱等分析手段进行表征.并选择了部分酞菁进行溴化,其中着重研究了不同中心金属以及溴化对染料Q带吸收的影响.结果表明,酞菁染料的金属化对于其Q带吸收影响很大,多数染料金属化后会出现蓝移,而选择合适的条件进行溴化,可以使得金属酞菁的Q带吸收出现一定程度的红移,其中部分溴化金属酞菁的吸收波长与光信息产业中使用的近红外激光器很接近,具有潜在的实用价值.     

PREPARATION OF MONODISPERSE CROSSLINKED POLYMER MICROSPHERES HAVING CHLOROMETHYL GROUP BY DISTILLATION-PRECIPITATION POLYMERIZATION

Monodisperse crosslinked poly(chloromethylstyrene-co-divinylbenzene) (poly(CMSt-co-DVB)) microspheres were prepared by distillation-precipitation copolymerization of chloromethylstyrene (CMSt) and divinylbenzene (DVB) in neat acetonitrile. The polymer particles had clean surfaces due to the absence of any added stabilizer. The size of the particles ranges from 2.59 μm to 3.19 μm and with mono-dispersity around 1.002-1.014. The effects of monomer feed in copolymerization on the microsphere formation were described. The polymer microspheres were characterized by SEM and chlorinity elemental analysis.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Change of water structure by solvents and polymers

Viscosity measurements have been made of water-solvent and water-polymer solutions in a temperature range of 20–60 centigrades. A medium structure temperatureT ₀ was calculated from the Vogel-equation. Water has a structure temperature of 140–150 K, its decrease indicates structure breakage, an increase structure promotion. Pyridine, dioxane, dimethylformamide and urea are structure breakers. This is explained by a shift of the equilibrium — bonded water molecules — nonbonded — to the right. Acetone shows hydrophobic bonding in the same concentration range of 0–10 mole % as the normal alcohols. They are quasifree liquids-structure temperature zero-in the pure state. This is explained by hydrogen bridged dimer formation with the exception of tert-butanol. Its 3 methylgroups sterically prevent dimer formation and cause structuring. Adding urea to methanol-water solutions breaks water structure according to urea concentration but extends the hydrophobic bonding maximum over the whole diagram. Glucose-water solutions have a minimum in the structure temperature diagram. Its left side indicates waterstructure breakage, its right side formation of a new structure forced upon water by the sugar. The equilibrium can be formulated: Waterlike bonded-nonbonded-hetero (solvent)-like bonded, Ribose also shows this minimum but after a short range of heterobondedness the structure is completely broken to nonbondedness.The polymers dextrane and polyvinylpyrrolidone are strong waterstructure breakers. Dextrane much stronger than PVP, it breaks to nonbondedness while PVP maintains a certain structuring, perhaps indicating heterobonding at higher concentrations. Polyacrylamide is a strong structurebreaker. It resembles urea in this sense. Perhaps the solvationwater structure of the NH₂ groups is very different from pure waterstructure. Polyacrylicacid breaks waterstructure completely, if sodiumchloride is added waterstructure is rebuilt again. The only waterstructure promoting polymer is natural gelatine. Perhaps this structure is different from pure water or the watermolecule equilibrium is shifted towards bondedness. The structure temperatures of pure polyethyleneglycoles show a minimum with increasing molecular weight. The high structure temperature of the small chains is explained by long chain assoziates formation through hydrogen bridging. This liquid of long assoziate chains is structured and has a high structure temperature. With increasing molecular weight ringformation instead of linear assoziation becomes possible. These neutral rings form a free liquid. Long chains again have a linear structure and the structure temperature increases at higher molecular weights. Existence of linear chain assoziation of low molecular PEGs is proved with their breakage by adding the chain terminating methanol.Dedicated to Prof. Dr. F. H. Müller.Herrn Chemotechniker D. Ziegler möchte ich für die sorgfältige Durchführung der Messungen sehr danken.Dem Verband der Chemischen Industrie danke ich sehr für die Ermöglichung der Arbeit.