原子吸收光谱法测定改性梨渣吸附Pb(Ⅱ)的研究

通过原子吸收光谱法研究了在不同pH、吸附剂量、Pb2+浓度和吸附时间条件下磷酸酯化改性梨渣吸附Pb2+的行为。结果表明:溶液初始pH 4.2时,Pb2+的吸附达到最大值;酯化梨渣≥10 g/L能除去Pb2+为30 mg/L溶液中的91%的Pb2+。酯化梨渣对Pb2+的吸附符合Langmuir等温模型,其最大吸附能力为43.99 mg/g。Pb2+达到吸附平衡的时间为40 min,准一级反应动力学方程可描述酯化梨渣对Pb2+的吸附过程。     

有机硅修饰的剥层水滑石及其对废水中金属离子的吸附

对剥层的镁铝硝酸根水滑石(Mg2Al-NO3-LDHs)片表面进行了有机硅化合物(N-(2-Aminoethyl)-3-aminopropyl)tris-(2-ethoxy)silane(KH-791)修饰,并研究了修饰后的水滑石片对废水中Pb2+,Cu2+和Zn2+离子的吸附行为。结果表明:在相同的温度和金属离子浓度条件下,被修饰的水滑石片对Pb2+吸附容量最大,达到378.0 mg.g-1;在以上几种金属离子的混合溶液中,修饰主体材料表现出对Pb2+高度的选择性吸附,对Pb2+吸附容量为85 mg.g-1,而对Zn2+和Cu2+的吸附容量只有30 mg.g-1左右。     

二硫代乙二酰胺改性硅胶固相萃取-火焰原子吸收光谱法测定水中的痕量铜和铅

制备了二硫代乙二酰胺改性硅胶作为固相萃取吸附剂,在pH 5.2,吸附时间为40min时,得到Cu2+、Pb2+的最大静态吸附容量,分别为19.50,29.39mg·g-1。水样中痕量的Cu2+、Pb2+经固相萃取后采用火焰原子吸收光谱法测定。在最佳条件下,Cu2+、Pb2+的线性范围分别为1.0~100,10~300μg·L-1,检出限(3S/N)分别为0.7,5.0μg·L-1。加标回收率在97.6%~104%之间。方法用于分析标准模拟水样,测定值与认定值相符。     

Chelex 100和Chilete P树脂分离水中Sr2+离子的研究

通过对Chelex 100和Chilete P两种螯合树脂对水中Sr2+离子的静态和动态分离研究,考察浓度、pH值、体积和流速等条件的影响,设计正交实验,摸索树脂动态吸附和洗脱的工艺路线。结果表明:Chelex 100比Chilete P具有更好的Sr2+离子吸附效果,静态分离回收率分别为71.48%和51.49%。Chelex 100树脂的动态分离工艺:浓度为250mg·mL-1、pH值为3的Sr2+离子溶液20mL,以流速为3ml.min-1通过层析柱吸附;8mol.L-1的HNO3溶液以流速为2ml.min-1进行Sr2+离子的洗脱;获得最终回收率为87.08%。     

交联黄原酸壳聚糖对铅离子的吸附研究

以壳聚糖为原料,通过交联和黄原酸化反应制备出交联黄原酸壳聚糖,采用FT-IR和XRD表征了其结构,并探讨壳聚糖及交联黄原酸壳聚糖对Pb2+的吸附性能。研究了初始溶液pH值、温度以及吸附时间等因素对Pb2+吸附量的影响。结果表明,在Pb2+起始浓度0.01 M,起始溶液pH=5,室温25℃吸附2h条件下,壳聚糖和交联黄原酸壳聚糖对铅离子的吸附量分别为126.8 mg/g和238.9 mg/g,交联黄原酸壳聚糖吸附能力为壳聚糖的1.89倍。     

聚(丙烯酸-co-丙烯酰胺)/蒙脱土/腐殖酸钠复合物对Pb2+的吸附性能

用制备的聚(丙烯酸-co-丙烯酰胺)/蒙脱土/腐殖酸钠复合吸附剂,研究了溶液pH值、吸附时间和Pb2+溶液初始浓度等因素对重金属Pb2+的吸附性能,探讨了复合吸附剂对Pb2+的吸附机理。结果表明,在pH值为6.0、吸附时间2 h、Pb2+溶液初始浓度0.01 mol/L和吸附剂用量0.10 g的条件下,复合吸附剂对Pb2+的吸附量达到364.05 mg/g,平衡所需的时间为15 min。与蒙脱土相比,复合吸附剂具有更高的吸附容量和更快的吸附速率。     

均苯四甲酸酐修饰壳聚糖微球对Pb2+和Cd2+的吸附

用交联的壳聚糖微球 (CTS) 与均苯四甲酸酐在无水条件下反应,合成均苯四甲酸酐修饰壳聚糖微球,并用FT-IR和XPS表征产物的结构。研究它对水溶液中Pb2+和Cd2+的吸附行为。考察溶液的pH,吸附时间及Pb2+和Cd2+的初始浓度对吸附金属离子的影响。吸附等温线可以用Langmuir 方程较好的描述,当pH 5.0时,该吸附剂对Pb2+和Cd2+的最大吸附量分别为296.7mg g-1和149.9mg g-1。动力学过程用二级吸附动力学模拟具有很好的线性相关性,从而确定了吸附过程为化学吸附。采用0.2mol L-1的EDTA为解析剂,Pb2+和Cd2+分别获得92.4%和85.3%的解析率。表明该吸附剂有再生性能。应用于电镀废水中铅的处理,结果满意。     

聚苯乙烯-甲基丙烯醛缩氨基硫脲固相萃取填料的制备及性能的研究

本文以苯乙烯、甲基丙烯醛和硫代氨基脲为原料,通过聚合、接枝制备出聚苯乙烯-甲基丙烯醛缩氨基硫脲固相萃取填料。采用红外光谱、扫描电子显微镜、X射线光电子能谱对其结构及元素组成进行分析。使用该填料制成固相萃取小柱,考察其对Ag~+、Pb~(2+)、Mn~(2+)、Cu~(2+)、Cd~(2+)、Fe~(3+)、Hg~(2+)、Ni ~(2+)、Co~(2+)和Cr~(3+)的吸附性能,吸附容量分别为12.21、11.42、7.20、12.42、10.07、9.28、11.78、7.34、9.64和10.42mg/g。实验确定样品最佳过柱流速为0.5mL/min,pH值为5,穿透体积为120mL。     

多壁碳纳米管对微量苯二氮卓类药物的吸附性能研究

研究了静态吸附条件下多壁碳纳米管(MWCNTs)对地西泮、艾司唑仑、阿普唑仑和三唑仑 4种苯二氮卓类药物的吸附性能,10 min内能达到吸附平衡.MWCNTs对药物的吸附容量随药物浓度的增加而增加,最小初始浓度时MWCNTs对4种药物的静态吸附容量分别为7.95、7.88、7.99和7.73 mg/g,吸附容量较大.295、303和313 K温度下的吸附实验表明,吸附容量随温度的升高而减小,降低温度有利于药物的吸附.对不同温度下的吸附等温线采用Freundlich和Langmuir方程进行拟合,结果显示Langmuir方程具有更好的拟合效果.在动态吸附条件下穿透体积的测定显示MWCNTs对药物也具有大的吸附容量且萃取回收率高达90%以上.     

螯合吸附材料ASA-PGMA/SiO2对稀土离子的吸附性能研究

采用静态吸附法研究了ASA-PGMA/SiO2对稀土离子的螯合吸附性能、吸附动力学和热力学。实验结果表明,其对稀土离子的吸附能力分别为:La3+:38.6 mg.g-1,Pr3+:39.6 mg.g-1,Nd3+:41.8 mg.g-1,Sm3+:42.8 mg.g-1,Tb3+:46.2 mg.g-1。吸附等温模型符合Lang-muir型单分子层吸附。介质pH值对材料的吸附能力有很大影响,pH值为6时吸附量最大。以盐酸为洗脱剂,当酸度为0.1 mol.L-1时,洗脱率为99.8%。连续吸附-脱附实验表明,ASA-PGMA/SiO2重复使用10次后,吸附能力变化很小。     

Adsorption of lead(II) from aqueous solution onto several types of activated carbon fibers

In this work, the adsorption of Pb(II) from aqueous solution was investigated on various types of activated carbon fibers (ACFs) manufactured from polyacrylonitrile and phenolic resin. The textural and physicochemical properties of the ACFs were determined by the N₂-BET method and acid-base titration. The experimental adsorption equilibrium data of Pb(II) on the ACFs were obtained in a batch adsorber, and the Langmuir isotherm model better fitted the experimental data. The effects of the type of ACF and precursor of ACF, solution pH and temperature upon the adsorption of Pb(II) on the ACFs were examined in detail. The adsorption capacity was highly dependent upon the precursor of ACF. The Pb(II) adsorption capacity of the ACFs augmented when the solution pH and temperature were increased from 2 to 4 and from 288 to 308 K, respectively. The effect of the pH was attributed to the interactions between the surface of the ACF and Pb²⁺ ions present in the water solution. The Pb(II) adsorption capacity of the ACFs was enhanced by oxidation with HNO₃ solution and the enhancement factor was between 1.1 and 1.4. The reversibility of the adsorption of Pb(II) was investigated by first adsorbing Pb(II) on an ACF and then desorbing the Pb(II). It was noticed that Pb(II) was substantially desorbed from ACF while reducing the solution pH to 2. It was concluded that the Pb(II) was mainly adsorbed on the ACFs by chemisorption, electrostatic interactions and ion exchange.     

Kinetics and equilibrium adsorption study of lead(II) onto activated carbon prepared from coconut shell

Removal of lead from aqueous solutions by adsorption onto coconut-shell carbon was investigated. Batch adsorption experiments were performed to find out the effective lead removal at different metal ion concentrations. Adsorption of Pb2+ ion was strongly affected by pH. The coconut-shell carbon (CSC) exhibited the highest lead adsorption capacity at pH 4.5. Isotherms for the adsorption of lead on CSC were developed and the equilibrium data fitted well to the Langmuir, Freundlich, and Tempkin isotherm models. At pH 4.5, the maximum lead adsorption capacity of CSC estimated with the Langmuir model was 26.50 mg g(-1) adsorbent. Energy of activation (Ea) and thermodynamic parameters such as DeltaG, DeltaH, and DeltaS were evaluated by applying the Arrhenius and van't Hoff equations. The thermodynamics of Pb(II) on CSC indicates the spontaneous and endothermic nature of adsorption. Quantitative desorption of Pb(II) from CSC was found to be 75% which facilitates the sorption of metal by ion exchange.     

交联聚丙烯腈螯合树脂对Pb(Ⅱ)的吸附及其在痕量分析中的应用

采用火焰原子吸收光谱法（FAAS）研究了交联聚丙烯腈螯合树脂对环境样品中Pb2+的吸附分离/富集行为,并考察了共存离子的干扰。 结果表明,该树脂对Pb2+的吸附率在溶液pH=5.4、静态吸附时间为1.5 h时室温下可达到90%。 在最佳吸附条件下,树脂对单一Pb2+的饱和吸附容量可达到49.6 mg/g。 以0.1 mol/L盐酸溶液作为解吸剂,可将吸附在树脂上的Pb2+定量洗脱,富集倍数和解吸率可分别达到50和97%。 富集50倍后,方法的检出限（3σ10）为5.3 μg/L;相对标准偏差（RSD）为2.1%;加标回收率为92.9%～97.6%。     

Researches on the Removal of Pb（Ⅱ） by Hydrothermally Modified Oyster Shells

A novel wastewater purification material was prepared by a hydrothermal method. It was mainly made from oyster shells with the merits of long service time, large surface area, high lead removal efficiency and excellent recyclable properties. The technological conditions were decided respectively based on the lead removal efficiencies. At pH = 5 and 30 ℃, for the wastewater with the initial concentration of Pb2+ to be 5 mg/L, adsorption time 24 h, and 1 mg to 40 mL of mass ratio between adsorbent and Pb2+, the maximum adsorption capacity can reach 0.19 mg/g. The lead removal material prepared by hydrothermal method has excellent recycle performance. The equilibrium adsorption capacity can get to 9.71 mg/g and the average Pb2+ removal rate is as high as 66.39%. After reusing for 60 times, the SEM observation shows that the hydrates of reticular formation is formed after hydrothermal modification, which provides a good attachment position for Pb2+, indicating the physical adsorption is dominant.     

乙二胺硅胶复合材料对Zn2+的吸附特性

以γ-氯丙基三氯硅烷为偶联剂,将乙二胺偶合接枝在硅胶表面,合成对锌离子具有吸附作用的乙二胺硅胶复合材料（EDA/SiO2）,考察了Zn2+溶液pH值、初始浓度、吸附温度和吸附时间等因素对复合材料吸附性能的影响。 结果表明,在研究的溶液浓度及温度范围内,Zn2+溶液pH值对EDA/SiO2的吸附量影响显著,吸附的最佳pH值范围在3.0~5.5;Zn2+的吸附平衡数据符合Langmuir吸附模型,热力学数据显示,EDA/SiO2对Zn2+的吸附行为为一吸热且自发进行的过程,升高温度有利于吸附,并对此吸附行为作了解释;吸附动力学数据可用拟二级吸附动力学方程描述,得到的吸附速率常数与溶液初始浓度有关。     

Adsorption of Pb(II) and Ni(II) From Aqueous Solution by a High-Capacity Industrial Sewage Sludge-Based Adsorbent

In the present study, adsorption of Ni(II) and Pb(II) from aqueous solution was investigated using activated carbon synthesized with industrial wastewater sludge. The synthesized adsorbent was analyzed using nitrogen adsorption–desorption and Fourier transfer infrared (FTIR) techniques. Batch adsorption mode was used to evaluate the effect of solution pH, contact time, adsorbent dose, initial metal ion concentration, and temperature on the adsorption capacity of the synthesized adsorbent. The kinetic data were analyzed using different kinetic models. The pseudo-second-order equation gave the best fit to the experimental data for both metal ions. The equilibrium isotherm data were analyzed using the Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherm models. The results showed that the data obtained for the Ni(II) and Pb(II) adsorption are in good agreement with the Langmuir model. The Langmuir mono-layer maximum adsorption capacities for Ni(II) and Pb(II) ions were estimated to be 74.06 and 88.76 mg g^?1 at 25°C, respectively. In addition, the thermodynamic studies proved that the adsorption process of both metals could be considered endothermic.     

Removal of uranium(VI) from aqueous solution by apricot shell activated carbon

Uranium is a toxic and radioactive heavy metal found in nuclear effluents and should be treated based on environmental considerations. The adsorption of uranyl cations (UO₂ ²⁺) by apricot shell activated carbon (ASAC) was investigated in a batch system. The effects of pH, contact time, temperature, adsorbent dosage on the adsorption kinetics and equilibrium adsorption isotherms of U(VI) were examined. The U(VI) uptake was fast within the first 60 min and reached an equilibrium state at 120 min. The adsorption process was highly pH dependent and the maximum adsorption was obtained at an initial solution pH of 6.0. Temperature over the range 25–45 °C had little effect on the U(VI) adsorption. The U(VI) removal efficiency increased concurrently with increasing ASAC dosage, whereas the U(VI) adsorption capacity decreased with increasing ASAC dosage. The adsorption process followed both Langmuir and Freundlich isotherms. On the basis of Langmuir model, the maximum adsorption capacity was found to be 59.17 mg U(VI)/g adsorbent. The adsorption kinetics can be very well defined by the pseudo-first-order rate model. The present results suggest that ASAC could be used as an adsorbent for an efficient removal of U(VI) from aqueous solution.