羧基化核壳磁性纳米Fe3O4吸附剂的制备及对Cu2+吸附性能

在以共沉淀法制备的磁性纳米Fe3O4粒子(Magnetic nanoparticles, MNP)表面进行了化学修饰, 制备了一种新型富含羧基功能团的核壳磁性纳米吸附剂(Carboxylic functionalized Fe3O4 magnetic nanoparticles, CMNP). 利用透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 X射线能量色散谱(EDS)、 振动样品磁强计(VSM)、 傅里叶变换红外光谱(FIIR)和热重分析仪(TGA)对CMNP的形貌、 结构、 化学组成和磁性能进行了表征, 并考察了吸附剂对Cu2+的吸附性能, 研究了溶液pH值、 吸附时间和Cu2+初始浓度对吸附性能的影响. 结果表明, 羧基化核壳磁性纳米Fe3O4颗粒的平均粒径为15 nm, 具有良好的超顺磁性, 饱和磁化强度为41.84 A·m2/kg, 在10 min中内可达到吸附平衡, 在pH=7.0时吸附量最高, 吸附等温数据符合Langmuir模型, 饱和吸附量qm= 43.48 mg/g.     

纳米Fe3O4/聚苯乙烯均匀分散体系的制备及结构

用化学共沉淀法制备了Fe3O4纳米颗粒,以油酸为表面活性剂,苯乙烯为载液,制备了稳定的纳米Fe3O4可聚合磁流体,将可聚合磁流体经自由基引发聚合制成纳米Fe3O4/聚苯乙烯均匀分散体系,用WAXRD研究了Fe3O4纳米粒子的结晶情况;用FTIR研究了油酸表面改性前后Fe3O4粒子表面官能团的变化;用TEM研究了Fe3O4颗粒的粒径大小及其在苯乙烯单体和聚苯乙烯中的分散情况;用DSC和TGA研究了纳米Fe3O4/聚苯乙烯均匀分散体系的玻璃化转变温度(Tg)和热稳定性,结果表明,合成的纳米Fe3O4为立方晶型,平均粒径在10nm左右,油酸分子在Fe3O4表面是化学吸附,经表面处理的Fe3O4超细颗粒在苯乙烯和聚苯乙烯基体中分散较均匀.界面粘结较好,含1.8％Fe3O4纳米颗粒的聚苯乙烯的最大热失重温度比聚苯乙烯提高了13K,Fe3O4/聚苯乙烯复合体系的饱和磁化强度σs为17.43emu/g.     

超顺磁性高分子微球的制备与表征

用化学共沉淀方法制备了Fe3O4纳米微粒,并用油酸(十八烯酸)和十二烷基苯磺酸钠为双层表面活性剂进行表面修饰,制备了稳定的水分散性纳米Fe3O4可聚合磁流体.在Fe3O4磁流体存在下,将苯乙烯与甲基丙烯酸通过乳液聚合方法制备了磁性高分子微球.透射电镜研究表明,Fe3O4微粒的平均粒径在10nm左右,乳液聚合形成的磁性高分子微球的粒径平均约为130nm;用超导量子干涉仪对微粒及高分子微球进行了磁性表征,结果表明,合成的Fe3O4纳米微粒以及磁性高分子微球均具有超顺磁性.同时,还用红外光谱及X射线衍射表征了磁性高分子微球的化学成分和晶体结构.用热失重方法测得磁性高分子微球中磁性物质的含量为23.6%.     

配体交换法制备水中高分散稳定性的多羧基修饰Fe3O4纳米颗粒

采用油相高温分解法制备了粒径可控且单分散的油溶性Fe3O4磁性纳米粒子(MNPs-OA), 并通过配体交换对其表面进行了亲水性修饰, 制备了柠檬酸(CA)、 N-(三甲氧基硅丙基)乙二胺三乙酸钠(SiCOOH)、 丁烷四羧酸(BTCA)和乙二胺四乙酸 (EDTA)四钠4种多羧基配体修饰的水溶性Fe3O4磁性纳米粒子(MNPs-CA, MNPs-SiCOOH, MNPs-BTCA 和MNPs-EDTA), 其中首次选用四羧基配体BTCA和EDTA四钠来修饰Fe3O4磁性纳米粒子(MNPs). 对油溶性MNPs和4种水溶性MNPs的形貌、 结构、 化学组成和磁性能进行了表征, 并对4种多羧基配体修饰的水溶性MNPs在水相中的稳定性和分散性进行了表征. 结果表明, 所得MNPs的平均粒径为15 nm, 具有超顺磁性, 配体交换后的水溶性MNPs具有良好的亲水性, 并在弱酸～碱性很宽的pH范围内具备良好的分散稳定性. 此类多羧基修饰的水溶性MNPs可与适当的阳离子聚电解质进行组装, 从而得到在磁靶向载体和磁共振造影(MRI)显影中具有良好应用前景的磁性自组装微囊.     

叶酸对磁性Fe_3O_4纳米粒子的表面修饰

以FeCl3·6H2O作为单一铁源,1,6-己二胺作为胺化试剂,利用无模板的溶剂热方法制备了胺基功能化的磁性Fe3O4纳米粒子,并利用其键合叶酸分子,制备出表面修饰了叶酸的磁性Fe3O4复合纳米粒子。利用傅里叶变换红外光谱仪、X-射线衍射仪、透射电镜、差热-热重分析仪和振动样品磁强计对所得纳米粒子的形貌、粒径、化学组成和磁性能进行了表征。结果表明,叶酸分子通过化学键牢固键合在磁性纳米Fe3O4粒子表面,叶酸修饰的复合纳米粒子仍然具有良好的磁性能。     

控制自由基聚合制备Fe_3O_4/SiO_2/P(AA-MMA-St)磁性复合微球

用原硅酸乙酯对Fe3O4纳米粒子进行表面改性得到Fe3O4/SiO2磁流体.在Fe3O4/SiO2磁流体存在下,以1,1-二苯基乙烯(DPE)为自由基聚合控制剂,利用乳液聚合法制备了Fe3O4/SiO2/P(AA-MMA-St)核-壳磁性复合微球.用红外光谱(FTIR)、振动样品磁强计(VSM)、透射电镜(TEM)、X光电子能谱(XPS)、热重分析(TGA)、示差扫描量热仪(DSC)对所制备的磁流体、磁性高分子复合微球的结构、形态、性能进行了表征.研究发现,原硅酸乙酯水解后能在Fe3O4表面形成硅膜保护层从而避免Fe3O4的酸蚀,使Fe3O4/SiO2/P(AA-MMA-St)复合微球的比饱和磁化强度比同样条件下制备的Fe3O4/P(AA-MMA-St)微球提高了28%;DPE能有效控制自由基在Fe3O4/SiO2磁流体表面均匀地引发单体聚合,得到平均粒径为422 nm,无机粒子含量为40%,比饱和磁化强度为34.850 emu/g,表面羧基含量为0.176 mmol/g的磁性复合微球.     

可控粒径纳米Fe_3O_4的制备及其磁性研究

本文用空气氧化法,在可见光作用下,添加配合剂(EDTA、柠檬酸、酒石酸、谷氨酸)在室温进行了不同粒径纳米Fe3O4的制备及其磁性能研究。结果表明:在可见光作用下,随EDTA、柠檬酸、酒石酸、谷氨酸等配合剂的添加,得到纳米Fe3O4的粒径有所减小、分散性有所提高;配合剂及可见光共存时,体系反应速率得到提高,高的反应速率使纳米Fe3O4晶粒减小;控制适当的光照度和添加剂的量,室温可得到11.8~29.6nm的Fe3O4颗粒。不同粒径纳米Fe3O4分别呈现出超顺磁性、铁磁性特征。     

单分散Fe_3O_4亚微米球的合成与表征

采用溶剂热法制备出具有尺寸可调、分散性好、亲水性和超顺磁性的亚微米Fe3O4磁球,并考察了不同表面活性剂、反应时间和反应温度的影响。分别采用XRD、FE-SEM、FTIR、超导量子干涉仪(SQUID)对其结构、形貌、表面性质及磁性进行了表征。结果表明,产物为立方结构、具有单分散性的Fe3O4亚微米球,粒径在140~360nm可调。所得Fe3O4亚微米球在室温条件下的磁滞回线表现出超顺磁性,矫顽力为零。不同表面活性剂对粒径大小和磁饱和强度有一定的影响,但对其形貌和晶相结构无影响。随着反应时间的延长和反应温度的提高,颗粒粒径有逐渐减小的趋势。     

高Fe_3O_4含量单分散P(St/AA)复合微球的合成与表征

在表面由十一烯酸和油酸共同修饰的Fe3O4磁流体存在下,以苯乙烯(St)和丙烯酸(AA)为共聚单体,用细乳液聚合法,制备了单分散,高Fe3O4含量,且表面带有羧基的超顺磁性高分子复合微球.采用透射电镜(TEM),热重分析(TGA),物性测量系统(PPMS),Zeta电位以及红外光谱等手段对磁性复合微球的各项性能进行表征.结果表明,Fe3O4粒子的表面改性是影响复合微球Fe3O4含量及形貌的关键因素.在优化的实验条件下,可以制得Fe3O4含量高达77wt%,平均粒径为137·9nm,表面羧基密度0·0894mmol/g,比饱和磁化强度为44·7emu/g的单分散超顺磁性高分子复合微球.     

1,1-二苯基乙烯存在下无皂乳液聚合制备磁性复合微球

报道了一种制备磁性复合微球的方法——DPE法.在自由基控制剂1,1-二苯基乙烯(DPE)存在条件下,甲基丙烯酸甲酯(MMA)与丙烯酸(AA)发生无皂乳液聚合,制备能与Fe3O4粒子相螯合的活性短链共聚物,加入Fe3O4粒子把短链共聚物引到其表面,引发其它单体继续在Fe3O4粒子表面聚合,制备磁性复合微球.研究了AA、DPE、引发剂及Fe3O4粒子加入量等对制备磁性复合微球的影响.并在此基础上,对优化后工艺制备的磁性复合微球进行了TEM、TGA及磁响应性表征.结果表明,利用该新的方法制备出了磁含量为20%、比饱和磁化强度为32.2emu/g、平均粒径为265nm且表面不含任何杂质的磁性复合微球.     

Development of Fe3O4-poly(l-lactide) magnetic microparticles in supercritical CO2

The Fe₃O₄-poly(l-lactide) (Fe₃O₄-PLLA) magnetic microparticles were successfully prepared in a process of solution-enhanced dispersion by supercritical CO₂ (SEDS), and their morphology, particle size, magnetic mass content, surface atom distribution and magnetic properties were characterized. Indomethacin (Indo) was used as a drug model to produce drug-polymer magnetic composite microparticles. The resulting Fe₃O₄-PLLA microparticles with mean size of 803 nm had good magnetic property and a saturation magnetization of 24.99 emu/g. The X-ray photoelectron spectroscopy (XPS) test indicated that most of the Fe₃O₄ were encapsulated by PLLA, which indicated that the Fe₃O₄-PLLA magnetic microparticles had a core–shell structure. After further loading with drug, the Indo-Fe₃O₄-PLLA microparticles had a bigger mean size of 901 nm, and the Fourier transform infrared spectrometer (FTIR) analysis demonstrated that the SEDS process was a typical physical coating process to produce drug-polymer magnetic composite microparticles, which is favorable for drugs since there is no change in chemistry. The in vitro cytotoxicity test showed that the Fe₃O₄-PLLA magnetic microparticles had no cytotoxicity and were biocompatible, which means there is potential for biomedical application.     

Hydrophilic dual‐responsive magnetite/PMAA core/shell microspheres with high magnetic susceptibility and ph sensitivity via distillation‐precipitation polymerization

A facile and effective approach to preparation of dual‐responsive magnetic core/shell composite microspheres is reported. The magnetite(Fe₃O₄)/poly(methacrylic acid) (PMAA) composite microspheres were synthesized through encapsulating γ‐methacryloxypropyltrimethoxysilane (MPS)‐modified magnetite colloid nanocrystal clusters (MCNCs) with crosslinked PMAA shell. First, the 200‐nm‐sized MCNCs were fabricated through solvothermal reaction, and then the MCNCs were modified with MPS to form active vinyl groups on the surface of MCNCs, and finally, a pH‐responsive shell of PMAA was coated onto the surface of MCNCs by distillation‐precipitation polymerization. The transmission electron microscopy (TEM) and vibrating sample magnetometer characterization showed that the obtained composite microspheres had well‐defined core/shell structure and high saturation magnetization value (35 emu/g). The experimental results indicated that the thickness and degree of crosslinking of PMAA shell could be well‐controlled. The pH‐induced change in size exhibited by the core/shell microspheres reflected the PMAA shell contained large amount of carboxyl groups. The carboxyl groups and high saturation magnetization make these microspheres have a great potential in biomolecule separation and drug carriers. Moreover, we also demonstrated that other magnetic polymeric microspheres, such as Fe₃O₄/PAA, Fe₃O₄/PAM, and Fe₃O₄/PNIPAM, could be synthesized by this approach. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Study on Fe3O4/polyaniline electromagnetic composite hollow spheres prepared against sulfonated polystyrene colloid template

Fe₃O₄/polyaniline (PANI) composite hollow spheres were prepared by using sulfonated polystyrene (SPS) microspheres as templates. The sulfonic acid groups were applied to induce absorbing Fe₃O₄ nanoparticle, and subsequently, conductive PANI was grown. Finally, the polystyrene cores were selectively dissolved to yield composite hollow microspheres with electromagnetic properties. The analysis results indicated that the adsorption of Fe₃O₄ on template core by electrostatic interaction resulted in magnetic composite microspheres. The conductivity of composite hollow spheres was remarkably increased after polyvinylpyrrolidone modification which favored the growth of PANI on SPS/Fe₃O₄ and enhanced the integrity of hollow microspheres. The saturated magnetization of the composite hollow microspheres was tuned from 2.7 to 9.1 emu/g, and the conductivity was in the range from 10^?2 to 10⁰?S/cm.     

Preparation and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>composite particles

Using Fe₃O₄ nano-particles as seeds, a new type of Fe₃O₄/Au composite particles with core/shell structure and diameter of about 170 nm was prepared by reduction of Au³⁺ with hydroxylamine in an aqueous solution. Particle size analyzer and transmission electron microscope were used to analyze the size distribution and microstructure of the particles in different conditions. The result showed that the magnetically responsive property and suspension stability of Fe₃O₄ seeds as well as reduction conditions of Au³⁺to Au⁰are the main factors which are crucial for obtaining a colloid of the Fe₃O₄/Au composite particles with uniform particle dispersion, excellent stability, homogeneity in particle sizes, and effective response to an external magnet in aqueous suspension solutions. UV-Vis analysis revealed that there is a characteristic peak of Fe₃O₄/Au fluid. For particles with d(0.5)=168 nm, the λmax is 625 nm.     

柠檬酸根对纳米Fe3O4颗粒的生长及性能的影响

现代诊断学的发展使得超小超顺磁性的Fe₃O₄粒子在医学领域具有重要应用价值。实验中利用某些羧酸盐对铁氧化物晶粒成长的抑制作用，在共沉淀法中引入柠檬酸根，制备出平均粒径小于5 nm的Fe₃O₄纳米分散体系。研究了不同柠檬酸根浓度对生成粒子的大小、结晶和表面吸附情况的影响。对Fe₃O₄颗粒在不同条件下的磁性与胶体稳定性进行了讨论。     

Preparation and clinical application of immunomagnetic latex

Magnetic poly(methyl methacrylate) (PMMA)/poly(methyl methacrylate‐co‐methacrylic acid) [P(MMA–MAA)] composite polymer latices were synthesized by two‐stage soapless emulsion polymerization in the presence of magnetite (Fe₃O₄) ferrofluids. Different types and concentrations of fatty acids were reacted with the Fe₃O₄ particles, which were prepared by the coprecipitation of Fe(II) and Fe(III) salts to obtain stable Fe₃O₄ ferrofluids. The Fe₃O₄/polymer particles were monodisperse, and the composite polymer particle size was approximately 100 nm. The morphology of the magnetic composite polymer latex particles was a core–shell structure. The core was PMMA encapsulating Fe₃O₄ particles, and the shell was the P(MMA–MAA) copolymer. The carboxylic acid functional groups (COOH) of methacrylic acid (MAA) were mostly distributed on the surface of the composite polymer latex particles. Antibodies (anti‐human immunoglobulin G) were then chemically bound with COOH groups onto the surface of the magnetic core–shell composite latices through the medium of carbodiimide to form the antibody‐coated magnetic latices (magnetic immunolatices). The MAA shell composition of the composite latex could be adjusted to control the number of COOH groups and thus the number of antibody molecules on the magnetic composite latex particles. With a magnetic sorting device, the magnetic immunolatices derived from the magnetic PMMA/P(MMA–MAA) core–shell composite polymer latex performed well in cell‐separation experiments based on the antigen–antibody reaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1342–1356, 2005     

基于静电喷射法活性多孔磁性炭球的制备及其对亚甲基蓝的吸附

在利用静电喷射一步法获得壳聚糖(CS)磁性微球(Fe₃O₄/CS)的基础上,对Fe₃O₄/CS进行高温炭化和碱活化处理获得活性磁性多孔炭球(A-Fe₃O₄/C),并对A-Fe₃O₄/C吸附水中亚甲基蓝(MB)分子的性能进行了研究。在利用扫描电子显微镜、红外吸收光谱仪、比表面分析仪对制备微球的形貌和结构进行分析的基础上,深入研究溶液pH、吸附时间、温度以及活化剂种类等因素对A-Fe₃O₄/C吸附性能的影响。研究结果表明,A-Fe₃O₄/C对MB的吸附量随着pH值的增加而增大,且经KOH活化后的A-Fe₃O₄/C对MB表现出较优的吸附性能。A-Fe₃O₄/C对MB的吸附过程符合伪二级动力学方程和Langmuir等温线模型,理论最大吸附容量可达300.6 mg·g^-1。此外,A-Fe₃O₄/C表现出良好的重复利用性能,6次循环后对MB的去除率没有明显下降。     

用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核，聚合物为中间层，金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF 8)。首先利用溶剂热法制备Fe₃O₄纳米粒子，然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层，最后通过原位沉积法在PAA外部包覆ZIF 8。在对Fe₃O₄@PAA@ZIF 8的组成和结构进行表征的基础上，深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示 Fe₃O₄@PAA@ZIF 8 具有明显的三层结构，Fe₃O₄的平均粒径为 117nm，PAA 层厚度约为 17 nm，ZIF 8层的厚度约为 14 nm。Fe₃O₄@PAA@ZIF 8对 MG 的吸附量随着 pH 的升高而增大，吸附过程符合准二阶动力学模型和 Langmuir等温吸附模型。此外，Fe₃O₄@PAA@ZIF 8还表现出良好的重复利用性能，8次循环利用后对MG(500 mg·L^-1)的最大吸附量仍可达982 mg·g^-1。     

用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核,聚合物为中间层,金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF-8)。首先利用溶剂热法制备Fe₃O₄纳米粒子,然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层,最后通过原位沉积法在PAA外部包覆ZIF-8。在对Fe₃O₄@PAA@ZIF-8的组成和结构进行表征的基础上,深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示Fe₃O₄@PAA@ZIF-8具有明显的三层结构,Fe₃O₄的平均粒径为117nm,PAA层厚度约为17 nm,ZIF-8层的厚度约为14 nm。Fe₃O₄@PAA@ZIF-8对MG的吸附量随着p H的升高而增大,吸附过程符合准二阶动力学模型和Langmuir等温吸附模...     

GO/Fe3O4/有机胺复合材料的制备及对结晶紫染料的吸附性能

用改进的Hummers法制备了氧化石墨烯,用乙二胺、乙二胺与丁二胺/己二胺混溶来改性氧化石墨烯。用水热法制备了Fe3O4,并用物理混合法制备了GO/Fe3O4/有机胺的三元复合体系。用透射电镜、扫描电镜、红外光谱、热重分析、X射线衍射、VSM和XPS等对所制得的样品进行了结构表征和性能测试,研究了三元复合粒子对结晶紫染料的吸附性能及影响结晶紫染料吸附效果的因素。结果表明:所制备的Fe3O4的平均粒径约为200 nm,粒径分布均匀;复合物中GO为典型的片状结构,GO及有机胺的掺杂没有影响Fe3O4的尖晶石结构;复合物为超顺磁性,Ms为53.0 emu·g~(-1)。吸附结果表明:石墨烯/Fe3O4/有机胺的三元复合材料对结晶紫染料的最大吸附量随浓度增大而增大,而吸附结晶紫染料的移除率却随结晶紫染料浓度增大而减小,并趋向一定值;乙二胺和己二胺混溶比例为5∶1的GO/Fe3O4复合材料吸附性能最佳:结晶紫浓度为400 mg·L~(-1),最大吸附量为164.3 mg·L~(-1)。