Influence of oxygen pressure on the ferroelectric properties of BiFeO3 thin films on LaNiO3/Si substrates via laser ablation

BiFeO₃(BFO) thin films of about 200 nm in thickness have been successfully grown on oxide bottom electrode, LaNiO₃(LNO), via pulsed laser ablation. X-ray diffraction spectrum of the as-deposited BFO film reveals a (100) preferred textured structure. The morphology of the BFO film is found to be strongly dependent on oxygen partial pressure in laser ablation. A saturated hysteresis loop with remanent polarization of 42 μC/cm² and coercive field of 100 kV/cm is obtained at the film deposition at 50 mTorr. The dielectric properties have also been obtained based on the influence of the oxygen pressure.     

Effect of film thickness on interface and electric properties of BiFeO3 thin films

Bismuth ferrite (BFO) thin films were fabricated by RF-magnetron sputtering deposition method on Pt/Ti/SiO₂/Si(1 0 0) substrate. The effect of the thickness of BFO films varying from 85 to 280 nm on electrical properties was investigated. Saturated coercive fields were found to increase with the BFO film thickness. The dielectric constant of BFO thin films measured at 1 kHz decreased with decreasing thickness from 98 to 86, while tangent losses increased from 0.013 to 0.021. The presence of bismuth oxide at the interface between BFO films and Pt bottom electrodes was responsible for the high leakage currents in thin BFO thin films as was demonstrated by X-ray diffraction, grazing-incident X-ray diffraction, and secondary ion mass spectroscopy analysis.     

Effect of bilayer structure and a SrRuO3 buffer layer on ferroelectric properties of BiFeO3 thin films

Effects of the BiFe_0.95Mn_0.05O₃ thickness and a SrRuO₃ (SRO) buffer layer on the microstructure and electrical properties of BiFeO₃/BiFe_0.95Mn_0.05O₃ (BFO/BFMO) bilayered thin films were investigated, where BFO/BFMO bilayered thin films were fabricated on the SRO/Pt/Ti/SiO₂/Si(100) substrate by a radio frequency sputtering. All thin films are of a pure perovskite structure with a mixture of (110) and (111) orientations regardless of the BFMO layer thickness. Dense microstructure is demonstrated in all thin films because of the introduction of BFMO layers. The SRO buffer layer can also further improve the ferroelectric properties of BFO/BFMO bilayered thin films as compared with those of these thin films without a SRO buffer layer. The BFO/BFMO bilayered thin film with a thickness ratio of 220/120 has an enhanced ferroelectric behavior of 2P _r??165.23???C/cm² and 2E _c??518.56?kV/cm, together with a good fatigue endurance. Therefore, it is an effective way to enhance the ferroelectric and fatigue properties of bismuth ferrite thin films by constructing such a bilayered structure and using a SRO buffer layer.     

Ferroelectric domain structures and polarization switching characteristics of polycrystalline BiFeO3 thin films on glass substrates

We investigated ferroelectric characteristics of BiFeO₃ (BFO) thin films on SrRuO₃ (SRO)/yttria-stabilized zirconia (YSZ)/glass substrates grown by pulsed laser deposition. YSZ buffer layers were employed to grow highly crystallized BFO thin films as well as SRO bottom electrodes on glass substrates. The BFO thin films exhibited good ferroelectric properties with a remanent polarization of 2P_r = 59.6 μC/cm² and fast switching behavior within about 125 ns. Piezoelectric force microscopy (PFM) study revealed that the BFO thin films have much smaller mosaic ferroelectric domain patterns than epitaxial BFO thin films on Nb:SrTiO₃ substrates. Presumably these small domain widths which originated from smaller domain energy give rise to the faster electrical switching behavior in comparison with the epitaxial BFO thin films on Nb:SrTiO₃ substrates.     

Highly (100)-oriented Eu-doped PZT thin films on sol-gel derived (100)-textured LaNiO<Subscript>3</Subscript>/Si substrates

(100)-oriented LaNiO₃ (LNO) thin films were grown on Si substrates by a sol-gel method followed by a rapid thermal process at temperatures ranging from 650 °C to 800 °C. The films produced at 700 °C had a resistivity of 1.79 mcm and could be used as bottom electrodes in the fabrication of ferroelectric capacitors on Si. Subsequently, a sol-gel derived Eu-doped Pb(Zr_0.52,Ti_0.48)O₃ (PEZT) thin film with a thickness of 130 nm prepared on the LNO electrode was found to have a (100)-oriented texture. Possible reasons for the high degree of (100) orientation in PEZT thin films are given. Good ferroelectric performance was obtained for Au/PEZT/LNO capacitors. The remnant polarization (2P_r) was found to be 22 C/cm² at a coercive electric field (E_c) of 134 kV/cm. After 10¹¹ polarization reversals, P_r decreased by only 15%. PACS 68.37.Yz; 68.37.Hk     

Effects of BaTiO<Subscript>3</Subscript> and SrTiO<Subscript>3</Subscript> as the buffer layers of epitaxial BiFeO<Subscript>3</Subscript> thin films

BiFeO₃ (BFO) thin films with BaTiO₃ (BTO) or SrTiO₃ (STO) as buffer layer were epitaxially grown on SrRuO₃-covered SrTiO₃ substrates. X-ray diffraction measurements show that the BTO buffer causes tensile strain in the BFO films, whereas the STO buffer causes compressive strain. Different ferroelectric domain structures caused by these two strain statuses are revealed by piezoelectric force microscopy. Electrical and magnetical measurements show that the tensile-strained BFO/BTO samples have reduced leakage current and large ferroelectric polarization and magnetization, compared with compressively strained BFO/STO. These results demonstrate that the electrical and magnetical properties of BFO thin films can be artificially modified by using a buffer layer.     

The ferroelectric and ferromagnetic characterization of CoFe2O4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multilayered thin films

The multiferroic (PMN-PT/CFO)_n (n = 1,2) multilayered thin films have been prepared on SiO₂/Si(1 0 0) substrate with LNO as buffer layer via a rf magnetron sputtering method. The structure and surface morphology of multilayered thin films were determined by X-ray diffraction (XRD) and atom force microscopy (AFM), respectively. The smooth, dense and crack-free surface shows the excellent crystal quality with root-mean-square (RMS) roughness only 2.9 nm, and average grain size of CFO thin films on the surface is about 44 nm. The influence of the thin films thickness size, periodicity n and crystallite orientation on their properties including ferroelectric, ferromagnetic properties in the (PMN-PT/CFO)_n multilayered thin films were investigated. For multilayered thin films with n = 1 and n = 2, the remanent polarization Pr are 17.9 μC/cm² and 9.9 μC/cm²; the coercivity H_c are 1044 Oe and 660 Oe, respectively. In addition, the relative mechanism are also discussed.     

Effects of Mn doping on BaTiO3 thin films grown on highly oriented pyrolytic graphite substrates

We report multiferroelectric properties of Mn-doped BaTiO₃ (MBTO) thin films on highly oriented pyrolytic graphite (HOPG) substrates. The MBTO thin films were grown on the HOPG substrate by pulse laser deposition. For comparison purpose, undoped BaTiO₃ (BTO) thin films were also prepared under same experimental conditions. The BTO and MBTO thin films were polycrystalline, indicating that the MBTO thin film has better crystallinity than the BTO thin film. The leakage current of the MBTO thin film was reduced due to the Mn doping substitution. In addition, the MBTO thin film exhibited better than the BTO thin film in ferroelectric and magnetic behaviors. We suggest that the Mn doping bring about the improvements of ferroelectric and ferromagnetic properties of the BTO thin films. Based on atomic force microscopy (AFM) and conducting AFM (CAFM) studies, the grain size of MBTO thin film was much larger than that of BTO thin film.     

Effect of pore size on ferroelectric properties of multiferroic BiFeO3 films prepared on porous silicon

The ferroelectric properties of BiFeO₃ (BFO) films spray deposited on porous silicon have been studied. The analysis of XRD and FESEM investigations show that the crystalline strain in the BFO films increases with pore size. The BFO films on porous silicon substrate showed improvement in ferroelectric fatigue behavior, remanent polarization and ferroelectric switching time. A maximum memory window of 5.54 V at 1 MHz and a large remanent polarization (P_r) of 13.1 μC/cm² have been obtained at room temperature. The improvement in the ferroelectric properties of these films has been correlated to the crystalline strain.     

La0.3Sr0.7TiO3模板层对Pb(Zr0.5Ti0.5)O3薄膜的铁电性能增强效应的研究

通过sol-gel法在Si (111) 基片上分别制备了LaNiO₃(LNO)底电极和LaNiO₃/La_0.3Sr_0.7TiO₃ (LNO/LSTO)底电极.然后采用sol-gel 方法，在两种衬底上分别制备了Pb (Zr_0.5Ti_0.5)O₃ (PZT)铁电薄膜.XRD分析表明，两种PZT薄膜均具有钙钛矿结构，且在LNO底电极上的PZT薄膜呈(100) 择优取向，而在LNO/LSTO底电极上的PZT薄膜呈随机取向.铁电性能测试表明，相对LNO衬底上制备的PZT薄膜，在LNO/LSTO底电极上制备的PZT薄膜的剩余极化强度得到了有效的增强，同时矫顽场也增大.介电常数和漏电流的测试表明，LNO/LSTO底电极上制备的PZT薄膜具有大的介电常数和漏电流. 关键词： PZT薄膜 铁电性 漏电流 0.3Sr_0.7TiO₃')" href="#">La_0.3Sr_0.7TiO₃     

Off-stoichiometry effects on BiFeO3 thin films

The effects of Bi and Fe-excess on the structure, ferroelectric, leakage current and magnetic properties of BiFeO₃ (BFO) thin films are reported. BFO with 5% excess exhibits no change in the structure with an improvement in leakage current properties in comparison to stoichiometric BFO. Raman spectroscopy of 10% Bi excess suggests a structural change from monoclinic to rhombohedral accompanied with an improvement of resistivity and ferroelectric polarization switching. A higher Fe-excess leads to the formation of pyrochlore Bi₂Fe₄O₉ and gamma-Fe₂O₃ that cause an increase in conductivity at the macroscopic scale. The results are discussed in terms of Fe and Bi-excess effects on the defect structure of BFO.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

Thickness dependent phase transformation of magnetron-sputtered Ni–Mn–Sn ferromagnetic shape memory alloy thin films

In this study, the influence of film thickness on the first-order martensite–austenite phase transformation of Ni–Mn–Sn ferromagnetic shape memory alloy thin films has been systematically investigated. Different thicknesses of the Ni–Mn–Sn films (from ~100 to 2,500 nm) were deposited by DC magnetron sputtering on Si (100) substrates at 550 °C. X-ray analysis reveals that all the films exhibit austenitic phase with the L2₁ cubic crystal structure at room temperature. The grain size and crystallization extent increase with the increase in film thickness, but the films with thickness above ~1,400 nm show structural deterioration due to the formation of MnSn₂ and Ni₃Sn₄ precipitates. The improvement in the crystallinity of the film with thickness is attributed to the decrease in film–substrate interfacial strain resulting in preferred oriented growth of the films. Temperature-dependent magnetization measurements as well as electrical measurements demonstrate the complete absence of phase transformation for the film of thickness of ~120 nm. For thickness greater than 400 nm, film exhibits the structural transformation, and it occurs at higher temperature with better hysteresis as film thickness is increased up to ~1,400 nm, after which degradation of phase transformation phenomenon is observed. This degradation is attributed to the disorders present in the films at higher thicknesses. Film with thickness ~1,400 nm possesses the highest magnetization with the smallest thermal hysteresis among all the films and therefore best suited for the actuators based on first-order structural phase transformation. Nanoindentation measurements reveal that the higher values of hardness and elastic modulus of about 5.5 and 215.0 GPa obtained in film of 1,014 nm thickness can considerably improve the ductility of ferromagnetic shape memory alloys (FSMA) and their applicability for MEMS applications. The exchange bias phenomenon is also found to be present in the films of thickness 1014, 1412, and 2022 nm exhibiting prominent martensitic transformation. Film of thickness 2,022 nm exhibits maximum exchange bias of ~50 Oe and higher exchange bias blocking temperature of 70 K as compared to other films.     

Thickness Dependence of Photoconductance in Strained BiFeO3 Thin Films With Planar Device Geometry

The recent discovery of efficient charge separation in tetragonal–rhombohedral (T‐R) polymorphic phase boundaries (PPBs) in strained BiFeO₃ (BFO) films is of great interest, and also raised a question of whether the PPBs could enhance the performance of BFO‐based planar photodetectors. To address it, we prepare BFO films with thickness ranging from 8 to 90 nm on the LaAlO₃ substrates, in which the BFO evolves from a pure T phase (without PPBs) to a T‐R mixed phase (with PPBs) due to the strain relaxation. Then, we comparatively investigate the photoconductive properties of these BFO films with the planar device geometry. It is found that the photoconductance first increases and then decreases with increasing film thickness. Particularly, the 50‐nm film containing the pure T phase without any detectable PPBs exhibits the highest photoconductance. This unexpected observation can be understood by analyzing the effects of increasing film thickness and associated phase evolution on the photoconduction‐related parameters.     

Photovoltaic effect in BiFeO3/BaTiO3 multilayer structure fabricated by chemical solution deposition technique

Photovoltaic (PV) properties of bismuth ferrite (BFO) and barium titanate (BTO) multilayered ferroelectric BFO/BTO/BFO/BTO thin film structure deposited on Pt/Ti/SiO₂/Si substrates using chemical solution deposition technique are presented. X-ray diffraction analysis confirms pure phase polycrystalline nature of deposited perovskite multilayered structures. Simultaneously both distorted rhombohedral (R3c) and tetragonal phases (P4mm) of the respective BFO and BTO components are also well retained. The ferroelectric sandwiched structures grown on fused quartz substrates exhibit high optical transmittance (~70%) with an energy band gap 2.62 eV. Current–voltage characteristics and PV response of multilayered structures is determined in metal-ferroelectric-metal (MFM) capacitor configuration. Considerably low magnitude of dark current density 1.53×10⁻⁷ A at applied bias of 5 V establish the resistive nature of semi-transparent multilayered structure. Enhanced PV response with 40 nm thin semitransparent Au as top electrode is observed under solid-state violet laser illumination (λ – 405 nm, 160 mW/cm²). The short circuit current density and open circuit voltage are measured to be 12.65 µA/cm² and 1.43 V respectively with a high retentivity. The results obtained are highly encouraging for employing artificial multilayered engineering to improve PV characteristics.     

The film thickness dependent thermal stability of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>:Ag thin films as high-temperature solar selective absorbers

The monolayer Al₂O₃:Ag thin films were prepared by magnetron sputtering. The microstructure and optical properties of thin film after annealing at 700 °C in air were characterized by transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and spectrophotometer. It revealed that the particle shape, size, and distribution across the film were greatly changed before and after annealing. The surface plasmon resonance absorption and thermal stability of the film were found to be strongly dependent on the film thickness, which was believed to be associated with the evolution process of particle diffusion, agglomeration, and evaporation during annealing at high temperature. When the film thickness was smaller than 90 nm, the film SPR absorption can be attenuated until extinct with increasing annealing time due to the evaporation of Ag particles. While the film thickness was larger than 120 nm, the absorption can keep constant even after annealing for 64 h due to the agglomeration of Ag particles. On the base of film thickness results, the multilayer Al₂O₃:Ag solar selective thin films were prepared and the thermal stability test illustrated that the solar selectivity of multilayer films with absorbing layer thickness larger than 120 nm did not degrade after annealing at 500 °C for 70 h in air. It can be concluded that film thickness is an important factor to control the thermal stability of Al₂O₃:Ag thin films as high-temperature solar selective absorbers.     

Study on ferroelectric polarization induced resistive switching characteristics of neodymium-doped bismuth ferrite thin films for random access memory applications

The present work reports on resistive switching (RS) characteristics of Neodymium (Nd)-doped bismuth ferrite (BFO) layers. The Nd (2–10 at%) doped BFO thin film layers were deposited using a spray pyrolysis method. The structural analysis reveals that a higher Nd doping concentration in BFO leads to significant distortion of the prepared Nd:BFO thin films from rhombohedral to tetragonal characteristics. The morphological analysis shows that all the deposited Nd:BFO thin films have regularly arranged grains. The X-ray photoelectron spectroscopy (XPS) analysis reveals that the prepared Nd:BFO thin films have a higher Fe ³⁺/Fe ²⁺ratio and less oxygen vacancy (V_O) defects which enriches the ferroelectric characteristics in Nd:BFO layers. The polarization-electric field (P-E) and RS characteristics of the fabricated Nd:BFO-based RS device were examined. It was observed that the Nd (7 at%) doped BFO RS device shows large remnant polarization (P _r) of 0.21 μC/cm² and stable RS characteristics.     

Ferroelectric,magnetoelectric and photoelectric properties of BiFeO3 /LaNiO3 heterostructure

BiFeO₃/LaNiO₃ (BFO/LNO) heterostructure was fabricated on quartz substrate via RF sputtering method. The microstructure and surface morphology of the BFO/LNO heterostructure was demonstrated. BFO layer shows good ferroelectric and weak ferromagnetic characters at room temperature. The dielectric constants of the heterostructure under an applied magnetic field 1.2T and zero field are both decreased with increasing frequency at room temperature and the dielectric constant under the applied magnetic field is larger, which is attributed to the coupling between the electric and magnetic dipoles, and further demonstrated in the framework of the Ginzburg-Landau theory for second phase transition. Additionally, the photoconductivity of the heterostructure under blue-laser illumination was observed, and the photoconductivity increase with the enhanced power of the blue-laser.     

Modification in structure of La and Nd co‐doped epitaxial BiFeO3 thin films probed by micro Raman spectroscopy

The influence of La and Nd co‐substitution on structure, electric and magnetic properties of epitaxial thin films of BiFeO₃ (BFO) was examined. We demonstrate structural phase transition in co‐doped La and Nd BFO thin films using Raman spectroscopy. Based on group theoretical analysis of the number and symmetry of Raman lines, we provide strong experimental evidence that the structure has been changed from rhombohedral to monoclinic due to co‐doping in BFO. The change in structure was also reflected in morphology of these films. Room temperature magnetic hysteresis curves showed that doped films exhibit enhanced ferromagnetic properties with remnant magnetization of ~10 emu/cm³ and coercive field of 1.2 kOe. The enhanced magnetic properties highlight the potential applications of doped BLNFO thin film for smart devices. Copyright © 2015 John Wiley & Sons, Ltd.