高功率,红光至中红外可调谐腔内和频光学参量振荡器

本文利用高重复频率,高平均功率大模场面积飞秒光纤激光器作为同步抽运源,抽运以多周期极化掺氧化镁铌酸锂为非线性晶体的单共振光学参量振荡器,获得了高功率可调谐红光至中红外光,信号光调谐范围为1450—2200 nm,闲频光调谐范围为2250—4000 nm,在2 W的抽运功率下,信号光输出波长为1502 nm时获得最大输出功率374 mW,转换效率为18.7%,脉冲宽度为144 fs,此时中红外输出中心波长为3.4μm,平均功率为166 mW.再利用BBO晶体对信号光进行腔内和频,获得和频光输出波长调谐范围为610—668 nm,在4.1 W抽运的情况下,最高平均功率为615 nm处的694 mW,转换效率达16.9%.     

飞秒BBO光参量放大中闲频光二次谐波的产生

由于相位匹配条件和非线性晶体透光范围的限制，400nm蓝光抽运的飞秒β-BaB₂O₄（BBO）光参量放大（OPA）输出的参量光调谐范围有限，很难得到波长小于460nm的蓝光和近紫外光.实验采用1kHz钛宝石九通啁啾脉冲放大器的倍频蓝光作抽运光，超连续白光 作种子光，在Ⅰ类非共线相位匹配条件下，利用宽带的飞秒BBO OPA，在一定的实验参数下 获得了530—810nm放大的信号光，以及810nm—17μm波段范围的闲频光.与此同时 ，还获得了410—700nm连续可调的闲频光的二次谐波，其与闲频光层叠分布，单脉冲能量 为26μJ，转换效率大于5%.仅利用单块晶体的飞秒BBO OPA就可以获得410—810nm连 续可调的飞秒脉冲输出，从而为更多研究和应用的需要提供了重要的光源.对飞秒光参量放 大中闲频光二次谐波产生的条件也进行了理论分析. 关键词： 二次谐波 闲频光 非共线相位匹配 飞秒光参量放大     

ps参量放大效应

本文报道用0.53μm波长超短脉冲序列泵浦角度调谐的LiNbO_3参量晶体,获得1%单程参量放大能量转换效率,并在0.8～1.6μm范围测得参量信号光和空载光波长调谐曲线.     

光参量振荡过程的物理图象及BBO参量振荡器

本文采用折射率面来描述光参量振荡过程的物理图象,获得了光参量振荡过程的相位匹配图象和频率调谐的简单的数学表达式,直观简洁地说明了光参量振荡器频率调谐曲线的调谐行为.我们用1.06μm和0.532μm激光泵浦β-BaB2O4(BBO)晶体,获得了角度调谐的BBO光参量振荡器的调谐范围分别为1.7～2.35μm及0.72～2.1μm,最大能量转换效率为15％,还讨论了输出能量与腔长的关系.     

基于闲频光谐振的中红外高能量、高光束质量KTiOAsO4光学参量振荡器

基于砷酸钛氧钾(KTA)晶体优良的非线性光学特性,研究了由1μm Nd:YAG纳秒脉冲调Q激光器泵浦的高能量、高光束质量闲频光单谐振光参量振荡器。选取合适镀膜参数的腔镜、优化腔型设计,建立了一个稳定紧凑的半球形对称闲频光单谐振腔,实现了高能量、高光束质量的近-中红外激光输出。在输入泵浦光的(1.064μm)最大能量为20.2 mJ时,输出信号光(1.535μm)和闲频光(3.468μm)的最大能量分别为2.91 mJ和1.13 mJ,对应信号光和闲频光的斜效率分别为20.9%和8.1%。闲频光单谐振的光参量振荡器具有更大的衍射损耗和光束发散角,可以极大的限制输出光束的光谱带宽、提高谐振闲频光的光束质量等优势,测量了输出中红外闲频光在两个正交方向上的光束质量因子分别为M_x²≈1.1,M_y²≈1.1。     

外腔式宽调谐被动调QNd:YVO_4/PPMgLN光学参量振荡器

报道了一个低阈值宽调谐、被动调Q、单谐振掺MgO的周期性极化铌酸锂晶体(PPMgLN)光学参量振荡器。利用被动调Q的Nd:YVO4激光器作为泵浦源,采用外腔结构,在室温下,实现了PPMgLN晶体的准相位匹配光学参量振荡。光参量振荡的阈值仅为0.27W(单脉冲能量4.5μJ、脉宽35ns);在泵浦光为1.35W(脉冲能量8.2μJ、脉宽35ns),PPMgLN周期为31μm时,获得了161.9mW,3.202μm脉冲激光输出;同时获得了98.5mW的1.594μm信号光输出,总的光光转化效率达到19.3%。通过改变晶体的周期,实现了闲频光3.13～4.19μm,信号光1.43～1.65μm的宽带可调谐激光输出。     

基于GaSe差频产生8～19μm可调中红外辐射

利用Nd:YAG激光器抽运内腔KTP光学参量振荡器,得到了输出为2μm附近的双波长,并在满足Ι类相位匹配条件下,在GaSe中共线差频产生8～19μm连续宽调谐调的中红外辐射.在8.76μm处脉冲最大能量达33.66μJ,峰值功率7.4kW,光子转换效率达4.43%左右.分析了影响能量转化效率的原因,提出了补偿走离的措施.     

基于复合腔的波长可调谐连续橙红色激光器

设计并研制了一种基于复合腔结构的波长可调谐、瓦级连续输出的橙红色激光器.该激光器是由半导体激光侧泵Nd∶GdVO_4晶体产生p-偏振1 062.9nm基频光的谐振腔和使用周期性极化晶体MgO∶PPLN(三个极化周期为29.0μm、29.8μm和30.8μm)的单共振光学参量振荡器组成.在两个谐振腔的重叠区域,利用Ⅱ类临界相位匹配KTP晶体对s-偏振信号光与p-偏振1 062.9nm基频光进行腔内和频.通过对MgO∶PPLN晶体进行三个不同极化周期的调谐和30℃~200℃范围内的温度调谐,在三个波段(613.4~619.2nm@29.0μm、620.2~628.9nm@29.8μm和634.4~649.1nm@30.8μm)获得了波长可调谐的橙红色激光连续输出,并在相应波段(3 980.0~3 758.5nm@29.0μm、3 714.2~3 438.3nm@29.8μm和3 278.0~2 940.2nm@30.8μm)获得了波长可调谐的中红外闲频光的连续输出.在30℃最低调谐温度,通过改变晶体的极化周期,在613.4nm、620.2nm和634.4nm处测得最大连续输出功率分别为1.52 W、2.21 W和3.03 W,对应的三束闲频光最大连续输出功率分别为2.36 W@3 980.0nm、3.17 W@3 714.2nm和4.13 W@3 278.0nm.     

板条放大器同步泵浦的宽调谐MgO:PPLN中红外光参量振荡器（英文）

搭建了Nd:YVO4/SESAM锁模激光器,采用LDA泵浦的Innoslab对其进行功率放大,最后同步泵浦MgO:PPLN实现了宽调谐皮秒中红外光参量运转。通过改变MgO:PPLN的温度和通道,实现了信号光1415~1557nm、闲频光3362~4290nm范围的宽调谐输出,其中最高的光光转换效率为17.5%。同步泵浦功率为16 W,脉冲重复频率为116.9 MHz时,同时获得1.33 W的1518nm信号光和1.26 W的3558nm闲频光输出。     

板条放大器同步泵浦的宽调谐MgO:PPLN中红外光参量振荡器（英）

搭建了Nd:YVO4/SESAM锁模激光器,采用LDA泵浦的Innoslab对其进行功率放大,最后同步泵浦MgO:PPLN实现了宽调谐皮秒中红外光参量运转。通过改变MgO:PPLN的温度和通道,实现了信号光1415~1557 nm、闲频光3362~4290 nm范围的宽调谐输出,其中最高的光光转换效率为17.5%。同步泵浦功率为16 W,脉冲重复频率为116.9 MHz时,同时获得1.33 W的1518 nm信号光和1.26 W的3558 nm闲频光输出。     

PUMP-TUNING KTP OPTICAL PARAMETRIC OSCILLATOR WITH CONTINUOUS OUTPUT WAVELENGTH PUMPED BY A PULSED TUNABLE Ti:SAPPHIRE LASER

We report on the implementation of a KTP optical parametric oscillator pumped by a pulsed tunable Ti:sapphire laser. Two major improvements were achieved, including the connection of the signal and idler tuning ranges and the high-output conversion efficiency through the signal and idler tuning ranges. Both in the signal and idler, the continuous output wavelength from 1.261 to 2.532μm was obtained by varying the pump wavelength from 0.7 to 0.98μm. The maximum output pulse energy was 27.2mJ and the maximum conversion efficiency was 35.7% at 1.311μm (signal).     

环形腔2.05μm单谐振KTP晶体光参量振荡器研究

针对大气CO_2浓度探测差分吸收激光雷达的应用需求,采用稳定环形腔和模式匹配设计,搭建了一套单纵模1 064nm激光泵浦的单谐振KTP晶体光参量振荡器,获得高斜率转换效率、基横模的2.05μm波长纳秒激光脉冲输出.在8字形环形行波稳定腔中,将2块II类相位匹配KTP晶体以走离补偿方式放置,在20Hz重复频率下,当泵浦单脉冲能量达到11mJ时,获得了单脉冲能量为2.4mJ的2.05μm信号光输出,脉宽约24ns,斜率效率达到53%.2.05μm信号光光束质量因子在x、y方向分别为1.3和1.2.     

Zig-Zag板条泵浦的2.12μm激光器

 为了实现窄脉宽、高峰值功率2.12 μm激光的稳定输出,设计了基于侧面泵浦Zig-Zag 板条产生1.06 μm基频光,进而泵浦KTP晶体通过II类相位匹配产生2.12 μm激光的光参量振荡实验。对外腔及内腔进行了实验研究,分别获得了1.53%和2.86%的电光转换效率。在20 Hz频率下内腔2.12 μm输出能量达到70 mJ以上,脉宽7 ns~9 ns。其中内腔实验中能量输出稳定度接近8%。     

Efficient, high-power, ytterbium-fiber-laser-pumped picosecond optical parametric oscillator

We report a high-power picosecond optical parametric oscillator (OPO) synchronously pumped by a Yb fiber laser at 1.064 μm, providing 11.7 W of total average power in the near to mid-IR at 73% extraction efficiency. The OPO, based on a 50 mm MgO:PPLN crystal, is pumped by 20.8 ps pulses at 81.1 MHz and can simultaneously deliver 7.1 W of signal at 1.56 μm and 4.6 W of idler at 3.33 μm for 16 W of pump power. The oscillator has a threshold of 740 mW, with maximum signal power of 7.4 W at 1.47 μm and idler power of 4.9 W at 3.08 μm at slope efficiencies of 51% and 31%, respectively. Wavelength coverage across 1.43-1.63 μm (signal) and 4.16-3.06 μm (idler) is obtained, with a total power of ~11 W and an extraction efficiency of ~68%, with pump depletion of ~78% maintained over most of the tuning range. The signal and idler output have a single-mode spatial profile and a peak-to-peak power stability of ±1.8% and ±2.9% over 1 h at the highest power, respectively. A signal pulse duration of 17.3 ps with a clean single-peak spectrum results in a time-bandwidth product of ~1.72, more than four times below the input pump pulses.     

Efficient conversion from 1 to 2 microm by a KTP-based ring optical parametric oscillator

Conversion of Q -switched 1.064-microm Nd:YAG laser pulses to the 2-2.2-mu; m region with 46% efficiency is demonstrated with a KTP-based type 2 phase-matched optical parametric oscillator (OPO) with two pairs of walk-off compensating crystals in a ring resonator. With 10 mJ of pump energy, we obtain 2.5 mJ at the 2.06-microm signal and 2.1 mJ at the 2.2-microm idler, with a beam quality of M(2) approximately 1.4 . With a ZnGeP(2) -based OPO pumped by the signal from the KTP OPO we achieved 14% conversion efficiency from 1.064microm to the 3-5-microm range.     

高峰值功率1．57μm脉冲激光器的研究

KTP非线性频率转换技术是实现人眼安全激光的有效方法,为了获得高峰值功率人眼安全激光,设计了一种级联式1．06μm泵浦非临界相位匹配环形腔KTP光参量振荡器一光参量放大器,并对其激光输出进行了测试,结果证明该光参量振荡器输出激光波长1．571μm,激光峰值功率42MW,光光转换效率35％,能量稳定度2．5％。该技术已用于计量检测标准光源,并在远程人眼安全激光测距仪、激光雷达等装备中具有应用前景。     

Generation of 2.1 μm wavelength from degenerate high gray track resistant potassium titanyl phosphate optical parametric oscillator

This paper presents the experimental results of degenerate optical parametric generation using a high gray track resistant potassium titanyl phosphate (HGTR KTP) optical parametric oscillator (OPO). An average output power of 7 W at 10 kHz has been achieved that includes both signal and idler powers near degeneracy using 20 W average power from a 1064 nm Nd:YVO₄ pump source corresponding to an optical conversion efficiency of 35%.     

High-energy PPMgLN optical parametric oscillator pumped by a 1.064 μm E-O Q-Switched Nd:YAG laser

A high-energy PPMgLN optical parametric oscillator (OPO) pumped by a E-O Q-switched Nd:YAG laser working at 1.064 μm was successfully illustrated. A maximum output pulse energy of 3.4 mJ was obtained with a pump threshold of 1.5 mJ and a slope efficiency of 30% around room temperature. The OPO output signal and idler wavelength were 1552 and 3384 nm, respectively. The damage to the input surface of PPMgLN crystal was carefully observed with a damage threshold of 4.6 J/cm².     

Compact, high-pulse-energy, picosecond optical parametric oscillator

We report a high-energy optical parametric oscillator (OPO) synchronously pumped by a 7.19 MHz, Yb:fiber-amplified, picosecond, gain-switched laser diode. The 42-m-long ring cavity maintains a compact design through the use of an intracavity optical fiber. The periodically poled MgO-doped LiNbO(3) OPO provides output pulse energies as high as 0.49 μJ at 1.5 μm (signal) and 0.19 μJ at 3.6 μm (idler). Tunability from 1.5 to 1.7 μm and from 2.9 to 3.6 μm is demonstrated, and typical M(2) values of 1.5 × 1.3 and 2.8 × 1.9 are measured for the signal and idler, respectively, at high power.