4.1μm高功率中红外内腔光参量振荡器

提出了一种紧凑型、声光调Q、高功率的4.1μm中红外内腔式氧化镁掺杂的周期性极化铌酸锂晶体光参量振荡激光系统.基于内腔单谐振光参量振荡器动力学模型,对内腔光参量振荡器的阈值倍数及下转换效率的影响因素进行分析,提出实验中对光参量振荡阈值调节的办法,优化了大功率情况下光参量振荡的下转换效率.引入共振泵浦与单端键合晶体方式提高了大功率泵浦的热稳定性.基于光场传输理论与谐振腔稳定性理论,并考虑增益介质热效应,数值模拟了大功率泵浦注入时腔内基频光、信号光及闲频光的三波光场模式匹配,以确保光参量振荡器在高功率下稳定运转.对光参量振荡阈值进行调节,提高了参量光的下转换效率,最终得到4.125μm的中红外高重频脉冲瓦级激光输出,激光重复频率1～100kHz可调,脉冲宽度小于9ns,最高单脉冲能量36.7J,最高峰值功率4.257kW,最高输出功率为1.12 W,其对应的下转换效率为29.7%,最大光光转换效率为4.26%.     

连续波光参量振荡器定向红外干扰

介绍了基于光纤激光器泵浦的光学参量振荡器发展现状及其在定向红外干扰技术中的应用前景,对定向红外干扰技术的一些基本原理进行了讨论。利用自研的一台基于光纤激光器泵浦的连续波光学参量振荡器,通过周期调谐的方式分别实现3.414,3.630和3.820 m的瓦级中红外激光输出。采用这3个波长的激光对中红外热像仪进行了干扰原理性实验。对比实验结果可以得出:对于3.820 m波长的中红外激光,当其辐照的HgCdTe探测器前功率密度大于10 W/cm2量级时,在传输750 m距离后,热像仪实现饱和效果并且非饱和区域图像灰度级发生较大变化,达到了掩盖有用信号的目的。     

连续波光参量振荡器定向红外干扰

介绍了基于光纤激光器泵浦的光学参量振荡器发展现状及其在定向红外干扰技术中的应用前景,对定向红外干扰技术的一些基本原理进行了讨论。利用自研的一台基于光纤激光器泵浦的连续波光学参量振荡器,通过周期调谐的方式分别实现3.414,3.630和3.820 m的瓦级中红外激光输出。采用这3个波长的激光对中红外热像仪进行了干扰原理性实验。对比实验结果可以得出:对于3.820 m波长的中红外激光,当其辐照的HgCdTe探测器前功率密度大于10 W/cm2量级时,在传输750 m距离后,热像仪实现饱和效果并且非饱和区域图像灰度级发生较大变化,达到了掩盖有用信号的目的。     

基于光学参量振荡器的可调谐红外激光的强度噪声特性

红外激光光源在微量气体、高分辨率光谱分析和量子光学研究等领域具有重要的应用.本文利用锁定单共振光学参量振荡器内腔标准具的方案获得了无跳模连续调谐的红外激光输出,理论和实验研究了红外激光的强度噪声特性,分析了影响强度噪声的因素.通过控制非线性晶体的温度和标准具调制信号实现了对红外激光强度噪声的抑制.当控制非线性晶体工作温度为60℃,内腔标准具调制信号为8 kHz时,单共振光学参量振荡器输出信号光和闲置光的强度噪声分别降低了11和8 dB.     

中红外连续波单谐振光学参量振荡器热致相位失配

为了研究热致相位失配对中红外连续波单谐振光学参量振荡器(CW-SRO)输出效率的影响, 结合CW-SRO计算模型和热传导方程,利用有限元分析方法,重点对输出3.3 m波长闲频光的CW-SRO进行了分析。计算了不同信号光输出耦合率及不同泵浦功率下CW-SRO晶体输出截面上热致相位失配量的分布。由计算结果可以看出：晶体吸收腔中振荡信号光是导致晶体热效应的主要因素;在相同的输入条件下,泵浦功率在30 W以上时CW-SRO的热致相位失配将会大大降低其泵浦损耗率;通过增加信号光输出耦合率的方法,可以减少热致相位失配对CW-SRO输出效率的影响,但CW-SRO的振荡阈值会增加。     

中红外连续波单谐振光学参量振荡器热致相位失配

为了研究热致相位失配对中红外连续波单谐振光学参量振荡器(CW-SRO)输出效率的影响, 结合CW-SRO计算模型和热传导方程,利用有限元分析方法,重点对输出3.3 m波长闲频光的CW-SRO进行了分析。计算了不同信号光输出耦合率及不同泵浦功率下CW-SRO晶体输出截面上热致相位失配量的分布。由计算结果可以看出:晶体吸收腔中振荡信号光是导致晶体热效应的主要因素;在相同的输入条件下,泵浦功率在30 W以上时CW-SRO的热致相位失配将会大大降低其泵浦损耗率;通过增加信号光输出耦合率的方法,可以减少热致相位失配对CW-SRO输出效率的影响,但CW-SRO的振荡阈值会增加。     

3~5μm光学参量振荡器研究进展及其应用

3⁵μm波段中红外激光在医疗、环保、军事等领域有着广泛的应用。固体激光器泵浦的光参量振荡器(OPO)是目前获得35μm波段中红外激光在医疗、环保、军事等领域有着广泛的应用。固体激光器泵浦的光参量振荡器(OPO)是目前获得3⁵μm激光的常用方式,是激光器领域研究的热点,国外已有报道采用ZGP-OPO方式获得27.1W的35μm激光的常用方式,是激光器领域研究的热点,国外已有报道采用ZGP-OPO方式获得27.1W的3⁵μm激光。介绍了OPO获得35μm激光。介绍了OPO获得3⁵μm激光的技术途径,以及中红外OPO的研究进展和在各个领域的应用。     

可调谐钛宝石激光抽运的KTP单谐振光学参量振荡器的研究

介绍了 70 0nm～ 980nm的脉冲可调谐钛宝石激光抽运的KTP单谐振光学参量振荡器。通过改变抽运光波长作为光学参量振荡器输出参量光的调谐方式 ,确定了KTP晶体最佳切割角度 (θ=6 2 .5°,φ =0°) ,实验上获得了 12 5 1nm～ 2 5 32nm的连续参量光输出 ,最大输出能量约为 2 7 2mJ,最大转换效率为 35 7% (1311nm处 )。     

高功率中红外MgO∶PPLN光参量振荡器

设计了一种高功率1.06μm激光泵浦单谐振中红外PPLN光参量振荡器并对其进行了研究,研究证明在MgO∶PPLN极化周期29.1μm,工作温度40℃时,采用工作频率10kHz、脉宽10ns、功率34W1.06μm激光进行泵浦,光参量振荡器输出3.81μm中红外波段激光,平均功率5.4 W,光光转换效率15.88%。研究结果可为设计和研究中红外激光光源提供参考。     

基于PPMgLn晶体全固态宽带可调光学参量振荡器

基于掺MgO周期极化铌酸锂晶体的光学参量振荡器是一种全固态中红外可调谐相干光源.泵浦源为1064 nm声光调Q Nd:YAG激光器.通过温度调谐实现了中红外可调谐参量光的输出,当晶体的温度从40°C升高到200°C时,获得信号光的输出范围为1.561 μm～1.670μm,空闲光的调谐范围为3.342 μm～2.932 μm.当泵浦源脉宽为70 ns,重复频率为10 kHz,平均功率为.161 W,获得波长为1631μm.当泵浦源脉宽为70 ns,重复频率为10 kHz,平均功率为1.61 W,获得波长为1631 nm信号光的输出功率为21 1 mW.     

Continuous-wave mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

This paper reports a continuous-wave （CW） mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate （PPLN） pumped by a diode-end-pumped CW Nd：YVO4 laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN＇s grating period of 28.5 μm and the temperature of 140℃, the maximum idler output power of 155 mW at 3.86 μm has been achieved when the 808 nm pump power is 8.5 W, leading to an optical-to-optical conversion efficiency of 1.82%.     

Continuous-wave mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

This paper reports a continuous-wave (CW) mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate (PPLN) pumped by a diode-end-pumped CW Nd:YVO$_{4}$ laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN's grating period of 28.5\,$\mu$m and the temperature of 140\du, the maximum idler output power of 155\,mW at 3.86\,$\mu$m has been achieved when the 808\,nm pump power is 8.5\,W, leading to an optical-to-optical conversion efficiency of 1.82{\%}.     

Tunable femtosecond laser in the visible range with an intracavity frequency-doubled optical parametric oscillator

We demonstrated experimentally a synchronously pumped intracavity frequency-doubled femtosecond optical parametric oscillator (OPO) using a periodically-poled lithium niobate (PPLN) as the nonlinear material in combination with a lithium triborate (LBO) as the doubling crystal. A Kerr-lens-mode-locked (KLM) Ti:sapphire oscillator at the wavelength of 790 nm was used as the pump source, which was capable of generating pulses with a duration as short as 117 fs. A tunable femtosecond laser covering the 624-672 nm range was realized by conveniently adjusting the OPO cavity length. A maximum average output power of 260 mW in the visible range was obtained at the pump power of 2.2 W, with a typical pulse duration of 205 fs assuming a sech2 pulse profile.     

Fiber optical parametric oscillator based on photonic crystal fiber pumped with all-normal-dispersion mode-locked Yb:fiber laser

We demonstrate a cost effective, linearly tunable fiber optical parametric oscillator based on a home-made photonic crystal fiber pumped with a mode-locked ytterbium-doped fiber laser, providing linely tuning ranges from 1018 nm to 1038 nm for the idler wavelength and from 1097 nm to 1117 nm for the signal wavelength by tuning the pump wavelength and the cavity length. In order to obtain the desired fiber with a zero dispersion wavelength around 1060 rim, eight sam- ples of photonic crystal fibers with gradually changed structural parameters are fabricated for the reason that it is difficult to accurately customize the structural dimensions during fabrication. We verify the usability of the fabricated fiber experimen- tally via optical parametric generation and conclude a successful procedure of design, fabirication, and verification. A seed source of home-made all-normal-dispersion mode-locked ytterbium-doped fiber laser with 38.57 ps pulsewidth around the 1064 nm wavelength is used to pump the fiber optical parametric oscillator. The wide picosecond pulse pump laser enables a larger walk-off tolerance between the pump light and the oscillating light as well as a longer photonic crystal fiber of 20 m superior to the femtosecond pulse lasers, resulting in a larger parametric amplification and a lower threshold pump power of 15.8 dBm of the fiber optical parametric oscillator.     

Tunable femtosecond near-infrared source based on a Yb:LYSO-laser-pumped optical parametric oscillator

We demonstrate a widely tunable near-infrared source from 767 nm to 874 nm generated by the intracavity second harmonic generation(SHG) in an optical parametric oscillator pumped by a Yb:LYSO solid-state laser. The home-made Yb:LYSO oscillator centered at 1035 nm delivers an average power of 2 W and a pulse duration as short as 351 fs. Two Mg O doped periodically poled lithium niobates(Mg O:PPLN) with grating periods of 28.5–31.5 μm in steps of 0.5 μm and19.5–21.3 μm in steps of 0.2 μm are used for the OPO and intracavity SHG, respectively. The maximum average output power of 180 m W at 798 nm was obtained and the output pulses have pulse duration of 313 fs at 792 nm if a sech2-pulse shape was assumed. In addition, tunable signal femtosecond pulses from 1428 nm to 1763 nm are also realized with the maximum average power of 355 m W at 1628 nm.     

中红外光学参量振荡器技术进展

3~5μm中红外激光器在环境污染检测、医疗、工业等领域具有重要的应用价值。本文总结了基于ZnGeP_2、MgO∶PPLN晶体的光参量振荡器(OPO)的国内外发展现状,分析了其各自不同结构系统设计的优势和发展前景。指出高功率、小体积、轻重量的光学参量振荡器是未来重要发展方向,发展的技术核心是生长更大尺寸的中红外激光晶体以及研制更高性能指标的OPO泵浦源,并对中红外激光器的发展趋势进行了展望。     

Synchronously pumped femtosecond optical parametric oscillator at 1053 nm

A femtosecond optical parametric oscillator synchronously pumped by a Ti:Sapphire oscillator is reported. By the cavity length tuning, the signal wavelength is continuously tuned from 1000 to 1200 nm. The average output power of 32 mW is obtained at 1053 nm. The pulse width is measured to be 342 fs by intensity autocorrelation method. In addition, we observed bichromatic emission during the cavity length tuning process. Supported by the National High Technology Program Research and Development Program of China, the National Natural Science Foundation of China (Grant Nos. 60490280 and 10804128), and the National Basic Research Program of China (Grant No. 2007CB815104)     

A narrow-linewidth optical parametric oscillator for mid-infrared high-resolution spectroscopy

We present a narrow-linewidth, singly-resonant cw optical parametric oscillator, emitting more than 1 W in the 2.7–4.2?µm range. The OPO is pumped by a narrow linewidth (40?kHz) fibre-laser system and the signal frequency is locked to a high-finesse Fabry–Pérot cavity in order to increase the spectral resolution, thus obtaining a residual linewidth of 70?kHz for the signal. We tested the spectral performance of our OPO on several transitions in the ν₁ rovibrational band of CH₃I, measuring line intensities and showing sub-Doppler dip detection.