带宽对脉冲贝塞尔光束传输的影响

从惠更斯-菲涅耳衍射积分公式出发得到具有高斯型频谱分布的脉冲贝塞尔光束频率域的传输表示式,并使用傅里叶变换最后推导了脉冲贝塞尔光束时间域的传输公式。根据得到的公式通过具体数值计算对脉冲贝塞尔光束在自由空间中的传输进行了研究。计算结果表明脉冲光束的带宽对脉冲贝塞尔光束传输中的脉冲时间延迟和脉冲宽度产生影响。具体表现为脉冲光束带宽的增宽使脉冲时间延迟增大,并使脉冲时间波形的后沿拖长,从而导致脉冲宽度增宽。脉冲时间延迟和脉冲宽度还随传输距离发生变化。脉冲光束传输距离越大,脉冲时间延迟越大,脉冲宽度变得越宽。     

三角形光脉冲在正色散光纤中产生的实验研究

利用一种无源非线性脉冲整形方法, 实现了在普通正色散(ND)光纤中产生三角形光脉冲, 此方法依赖于脉冲预啁啾和脉冲在ND光纤中传输时群速度色散与自相位调制的相互作用. 实验研究表明, 在较宽的脉冲预啁啾值范围内, 通过优化脉冲输入功率和脉冲传输的ND光纤长度, 均可得到典型的三角形光脉冲: 脉冲时域形状前后沿的变化率接近恒定、整个脉冲具有线性频率啁啾. 另外, 在不同的脉冲预啁啾下, 要得到高质量的三角形光脉冲, 均需要较高的脉冲输入功率; 并且脉冲预啁啾较大时, 三角形脉冲的形成对ND光纤长度和脉冲输入功率有较大的容差, 易获得三角形光脉冲.     

可用于高速摄影脉冲氙灯的研究

为了研究储能电容初始电压、电极间距、充气压及灯管内径等条件对脉冲氙灯电流脉冲和发光脉冲的影响,在电极间距100~300mm、充气压13.33~53.32kPa、灯管内径6~12mm、储能电容初始电压1.75~4.25kV的条件下,分别测量了脉冲氙灯的电流脉冲和发光脉冲的变化状况。测量得到脉冲氙灯的电流脉冲宽度和发光脉冲宽度均在15~45μs之间。对比发现:储能电容初始电压较高有助于获得高峰值、窄脉宽且滞后时间短的电流脉冲;具有较高充气压或较长电极间距的脉冲氙灯其电流脉冲与发光脉冲的峰值较小、脉冲宽度较大,且发光脉冲滞后时间较长;较粗灯管内径虽然可以增加电流脉冲的峰值,但电流脉冲的宽度被增宽,发光脉冲峰值减小,发光脉冲宽度展宽,且延长了发光脉冲的滞后时间.     

一种高双折射光子晶体光纤中的脉冲俘获分析

数值模拟分析了一种新型高双折射光子晶体光纤中的脉冲俘获现象,以及泵浦脉冲入射条件对脉冲俘获效果的影响机理.结果表明：泵浦脉冲和信号脉冲处于零色散点附近,且分别处于光子晶体光纤的反常和正常色散区,其走离参量的数值小于10－12 s/m时,可以实现脉冲俘获|泵浦脉冲和信号脉冲的时域中心延迟对泵浦脉冲光谱红移量和信号脉冲光谱蓝移量影响很小,但时域中心延迟越大,信号脉冲的输出频谱越窄,俘获效果越差|提高泵浦脉冲峰值功率,可明显增大泵浦脉冲光谱红移量和信号脉冲光谱蓝移量,为实现不同波长范围的全光开关提供了条件|泵浦脉冲半宽度越大,泵浦脉冲频谱越宽,信号脉冲频谱越窄,俘获效果越不明显.     

时域超短脉冲光栅记录和读取的研究

为实现超短脉冲信号的重现或整形,从理论上推导了时域超短脉冲光栅的记录和读取,并结合高斯型脉冲分布,讨论了信号脉冲、参考脉冲和读出脉冲宽度不同时的衍射结果,提出了利用超短脉冲全息实现超短脉冲信号的重现或整形等功能的方法.结果发现,长信号脉冲和短参考脉冲干涉记录全息后,如果用足够短的脉冲读取,衍射完全再现了原输入信号脉冲.但是在读出脉冲带宽接近于信号带宽时,衍射波频谱宽度有一定程度减小.     

飞秒脉冲初始脉宽和啁啾对其自相似演化及压缩的影响

采用自相似抛物脉冲放大器对飞秒脉冲直接进行放大,并以低非线性系数的光子带隙光纤作为脉冲压缩器对放大的脉冲进行压缩.通过分步傅里叶方法研究了飞秒脉冲的初始宽度和啁啾对其自相似演化和压缩的影响.研究结果表明脉冲宽度越宽,脉冲自相似演化程度越差,演化脉冲的压缩质量也越差,压缩脉冲宽度较大,且有基座;脉冲的初始啁啾会严重阻碍其自相似演化,并最终影响脉冲的压缩质量;啁啾越大,脉冲的自相似演化结果越差,脉冲的压缩质量也越差;正的啁啾对脉冲的自相似演化的影响比负啁啾的要大.     

基于交叉相位调制的堆积脉冲非线性传输

基于子脉冲交叉相位调制的非线性相互作用,利用耦合非线性传输模型,对堆积脉冲的非线性传输和峰均比进行了研究.研究发现,当堆积脉冲的子脉冲间存在重叠时,在传输过程中时间相干会导致子脉冲间发生相互作用从而改变其脉冲质量.在不同的子脉冲延迟情况下,堆积脉冲的强度和峰均比随传输距离的变化而改变,且变化幅度均随子脉冲延迟的增大而减小.对于高斯型堆积脉冲,当归一化子脉冲延迟大约为3时其在非线性传输过程中保持脉冲形状基本不变;而对于超高斯型的堆积脉冲,归一化子脉冲延迟则约为2.2.     

脉冲形状对脉冲经光纤放大器传输后功率增益的影响

基于描述脉冲放大过程的时间相关非线性辐射迁移方程,对不同形状脉冲经掺镱光纤放大器传输后的功率特性进行了分析,该方程同时考虑了光与介质的相互作用.数值结果表明,在相同的脉冲能量下,不同形状脉冲经放大器放大后的功率增益随入射脉冲形状不同而不同,并且功率增益的差异在脉冲前沿比较大.这使得放大器输出脉冲峰值向前沿的偏移量以及峰值功率的放大倍数都与脉冲形状有关.尤其是当入射脉冲的能量较大时,不同形状脉冲的峰值功率的放大倍数明显不同,以超高斯脉冲为最大,高斯脉冲、双曲正割脉冲次之,洛伦兹脉冲最小.     

超短双曲正割脉冲的两种脉冲宽度比较

利用理论推导和数值模拟方法,给出了超短双曲正割脉冲较为严格的均方根脉冲宽度与通常使用的半高全宽脉冲宽度的解析表达式,并对两种脉冲宽度进行了比较.研究结果表明,对于亚周期（半高全宽脉冲宽度小于一个光学振荡周期）双曲正割脉冲,均方根脉冲宽度与半高全宽脉冲宽度有较大的差异,并且绝对相位对均方根脉冲宽度的影响很大.所以描述亚周期双曲正割脉冲时应该使用更加严格的均方根脉冲宽度.     

强短脉冲辐照叠加态原子增强阿秒脉冲强度

采用强短激光脉冲辐照叠加态原子提高孤立阿秒脉冲的强度。数值研究表明,与强短脉冲 (脉冲宽度只有几个光学周期的超短脉冲）辐照基态原子获得孤立阿秒脉冲相比,采用叠加 态原子的方案不仅同样可以获得孤立的阿秒脉冲,而且阿秒脉冲的强度得到显著增强。     

半导体激光器泵浦的Cr:LiSAF激光器

本文报道了用半导体激光器泵浦Cr:LiSAF激光器腔的设计以及输出特性,在用准连续波泵浦时,阈值平均功率为42mW,在泵浦平均功率为60mW时得到了3mW的激光输出.     

All-solid-state continuous-wave frequency doubling Nd:YLF/LBO laser with 2.15 W output power at 526 nm

An efficient and compact green laser at 526 nm generated by intracavity frequency doubling of a continuous wave (CW) laser operation of a diode pumped Nd:YLF laser at 1053 nm under the condition of suppression the high gain transition at 1047 nm. With 19.5 W diode pump power and a frequency doubling crystal LBO, as high as 2.15 W of CW output power at 526 nm is achieved, corresponding to an optical-to-optical conversion efficiency of 11.2% and the output power stability in 8 h is better than 2.87%. To the best of our knowledge, this it the highest watt-level laser at 526 nm generated by intracavity frequency doubling of a diode pumped Nd:YLF laser at 1053 nm.     

High power all-solid-state quasi-continuous-wave tunable Ti: sapphire laser system

This paper reports a high power, all-solid-state, quasi-continuous-wave tunable Ti:sapphire laser system pumped by laser diode (LD) pumped frequency-doubled Nd:YAG laser. The maximum tuned output power of 4.2 W (797 nm) and tuned average power of 3.7 W were achieved when fixing the Ti:sapphire broadband output power at 5.0 W and applying 750-850 nm broadband coated mirror.     

Efficient Nd:YVO_4 laser in-band pumped by wavelength-locked 913.9-nm laser diode and Q-switch operation

An efficient 1064-nm Nd:YVO_4laser in-band pumped by a wavelength-locked laser diode(LD) at 913.9 nm was demonstrated. The maximum continuous wave(CW) output power of 23.4 W at 1064 nm was realized with the incident pump power of 40 W, corresponding to a total optical-to-optical efficiency of 58.5%. This is to the best of our knowledge the highest total optical-to-optical efficiency and output power of Nd:YVO_4laser in-band pumped by a 913.9-nm laser diode.The Q-switched operation of this laser was also investigated. Through a contrast experiment of pumping at 808 nm, the experimental results showed that an Nd:YVO_4laser in-band pumped by a wavelength-locked LD at 913.9 nm had excellent pulse stability and beam quality for high repetition rate Q-switching operation.     

激光二极管抽运Nd∶YVO4晶体1342nm和671nm激光器研究

报道了激光二极管抽运的Nd∶YVO₄晶体1342和671nm激光特性.1342nm激光最大输出功率为1.75W，光-光转换效率为32.1%，斜效率为43%.利用Ⅰ类非临界相位匹配LBO晶体腔内倍频，当输入抽运功率为6W时，获得功率为502mW的671nm激光输出，光-光转换效率超过8.3%；当671nm激光输出功率为400mW时，短期的不稳定度小于2%. 关键词：     

All-solid-state continuous-wave frequency doubling Nd:LuVO4/LBO laser with 9.6 W output power at 672 nm

An efficient and compact red laser at 672 nm is generated by intracavity frequency doubling of a continuous wave (CW) laser operation of a diode pumped Nd:LuVO₄ laser at 1344 nm under the condition of suppression the higher gain transition near 1064 nm. With 38 W diode pump power and a frequency doubling crystal LBO, as high as 9.6 W of CW output power at 672 nm is achieved, corresponding to an optical-to-optical conversion efficiency of 25.3% and the output power stability in 8 h is better than 2.38%. To the best of our knowledge, this it the highest conversion efficiency of watt-level laser at 672 nm generated by intracavity frequency doubling of a diode pumped Nd:LuVO₄ laser at 1344 nm.     

二极管侧泵浦单横模1kHz电光Q开关激光器

 本文介绍了二极管侧泵浦Nd:YAG板条1kHz重复频率Q开关激光器的研制,实验获得最大单脉冲能量0.712mJ,脉宽小于10ns的输出。对Nd:YAG板条进行了三种冷却方式的比较实验,实验证明DPL在高重复频率工作时,激光介质的热效应是影响高重复频率工作的激光器效率的重要因素。     

All-solid-state continuous-wave frequency doubling Nd:YAG/LBO laser with 8.2 W output power at 660 nm

An efficient and compact red laser at 660 nm is generated by intracavity frequency doubling of continuous wave (CW) laser operation of a diode pumped Nd:YAG laser at 1319 nm under the condition of suppression the higher gain transition near 1064 and 1319 nm under the condition of suppression the higher gain transition near 1064 and 1338 nm. With 40 W diode pump power and a frequency doubling crystal LBO, as high as 8.6 W of CW output power at 660 nm is achieved, corresponding to an optical-to-optical conversion efficiency of 21.5% and the output power stability in 8 h is better than 2.73%. To the best of our knowledge, this it the highest conversion efficiency of watt-level laser at 660 nm generated by intracavity frequency doubling of a diode end pumped Nd:YAG laser at 1319 nm.     

An efficient continuous-wave YVO_4/Nd:YVO_4/YVO_4 self-Raman laser pumped by a wavelength-locked 878.9 nm laser diode

We report an efficient continuous-wave self-Raman laser at 1176 nm based on a 20-mm-long composite YVO_4/Nd:YVO_4/YVO_4 crystal and pumped by a wavelength-locked 878.9 nm diode laser.A maximum output power of 5.3 W is achieved at a pump power of 26 W,corresponding to an optical conversion efficiency of 20%and a slope efficiency of 21%.The Raman threshold for the diode pump power was only 0.92 W.The results reveal that in-band pumping by a wavelength-locked diode laser significantly enhances output power and efficiency of self-Raman lasers by virtue of improved pump absorption and relieved thermal loading.     

全固态Cr:LiSAF激光器的研究

本文报道了红光激光二极管泵浦的Cr:LiSAF激光器.采用纵向泵浦的平凹腔结构,在脉冲方式泵浦下,当泵浦平均功率为54mW,重复频率为200Hz时得到平均功率为5mW的激光输出,在连续波状态下,测得了输出功率随泵浦功率的变化曲线.激光输出的中心波长为873nm.