Kinetic evaluation of highly active supported gold catalysts prepared from monolayer-protected clusters: an experimental Michaelis-Menten approach for determining the oxygen binding constant during CO oxidation catalysis

Thiol monolayer-protected Au clusters (MPCs) were prepared using dendrimer templates, deposited onto a high-surface-area titania, and then the thiol stabilizers were removed under H2/N2. The resulting Au catalysts were characterized with transmission electron microscopy, X-ray photoelectron spectroscopy, and infrared spectroscopy of adsorbed CO. The Au catalysts prepared via this route displayed minimal particle agglomeration during the deposition and activation steps. Structural data obtained from the physical characterization of the Au catalysts were comparable to features exhibited from a traditionally prepared standard Au catalyst obtained from the World Gold Council (WGC). A differential kinetic study of CO oxidation catalysis by the MPC-prepared Au and the standard WGC catalyst showed that these two catalyst systems have essentially the same reaction order and Arrhenius apparent activation energies (28 kJ/mol). However, the MPC-prepared Au catalyst shows 50% greater activity for CO oxidation. Using a Michaelis-Menten approach, the oxygen binding constants for the two catalyst systems were determined and found to be essentially the same within experimental error. To our knowledge, this kinetic evaluation is the first experimental determination of oxygen binding by supported Au nanoparticle catalysts under working conditions. The values for the oxygen binding equilibrium constant obtained from the Michaelis-Menten treatment (ca. 29-39) are consistent with ultra-high-vacuum measurements on model catalyst systems and support density functional theory calculations for oxygen binding at corner or edge atoms on Au nanoparticles and clusters.     

新型晶须状氧化钛担载Au的CO催化氧化性能

从钛钾比较高的二钛酸钾晶须出发,通过离子交换和热处理等步骤制备了具有不同微观结构的晶须状TiO2,然后通过均相沉积-沉淀法在制得的TiO2上担载1%的Au.采用X射线衍射、扫描电镜、低温N2吸附-脱附及透射电镜等技术对催化剂样品进行了表征,并测定了其催化CO氧化反应性能.结果表明,600℃处理所得晶须状TiO2载体(T(600))具有丰富的介孔结构,比表面积为59 m2/g,平均孔径为11 nm,担载Au后其孔道结构保持良好,而800℃处理所得晶须状TiO2样品(T(800))孔结构完全坍塌,但仍保持纯锐钛矿晶型.在相同担载条件下Au/T(800)上的Au颗粒尺寸明显小于Au/T(600)上的,但两者催化CO氧化反应活性相差不大,CO完全转化温度分别为80和70℃,活性均比Au/P25的高.     

Oxygen-deficient titania as alternative support for Pt catalysts for the oxygen reduction reaction

Insufficient electrochemical stability is a major challenge for carbon materials in oxygen reduction reaction （ORR） due to carbon corrosion and insufficient metal-support interactions. In this work, titania is explored as an alternative support for Pt catalysts. Oxygen deficient titania samples including TiO2-x and TiO2_xNy were obtained by thermal treatment of anatase TiO2 under flowing H2 and NH3, respectively. Pt nanoparticles were deposited on the titania by a modified ethylene glycol method. The samples were characterized by N2-physisorption, X-ray diffraction and X-ray photoelectron spectroscopy. The ORR activity and long-term stability of supported Pt catalysts were evaluated using linear sweep voltammetry and chronoamperometry in 0.1 mol/L HC104. Pt/TiO2_x and Pt/TiO2_xNy showed higher ORR activities than Pt/TiO2 as indicated by higher onset potentials. Oxygen deficiency in TiO2-x and TiO2-xNy contributed to the high ORR activity due to enhanced charge transfer, as disclosed by electrochemical impedance spectroscopy studies. Electrochemical stability studies revealed that Pt/TiOE_x exhibited a higher stability with a lower current decay rate than commercial Pt/C, which can be attributed to the stable oxide support and strong interaction between Pt nanoparticles and the oxygen-deficient TiO2-x support.     

The mechanism of the water-gas shift reaction on Cu/TiO2(110) elucidated from application of density-functional theory

The Cu/TiO(2)(110) surface displays a great catalytic activity toward the water-gas shift reaction (WGSR), for which Cu is considered to be the most active metal on a TiO(2)(110)-supported surface. Experiments revealed that Cu nanoparticles bind preferentially to the terrace and steps of the TiO(2)(110) surface, which would not only affect the growth mode of the surface cluster but also enhance the catalytic activity, unlike Au nanoparticles for which occupancy of surface vacancies is favored, resulting in poorer catalytic performance than Cu. With density-functional theory we calculated some possible potential-energy surfaces for the carboxyl and redox mechanisms of the WGSR at the interface between the Cu cluster and the TiO(2) support. Our results show that the redox mechanism would be the dominant path; the resident Cu clusters greatly diminish the barrier for CO oxidation (22.49 and 108.68 kJ mol(-1), with and without Cu clusters, respectively). When adsorbed CO is catalytically oxidized by the bridging oxygen of the Cu/TiO(2)(110) surface to form CO(2), the release of CO(2) from the surface would result in the formation of an oxygen vacancy on the surface to facilitate the ensuing water splitting (barrier 34.90 vs. 50.49 kJ mol(-1), with and without the aid of a surface vacancy).     

Cu/Zn、Cu/Zn/Ni催化剂甲醇部分氧化制氢

研究了甲醇在Cu/Zn及Cu/Zn/Ni催化剂上部分氧化热耦合裂解制氢的反应,系 统地考察了不同O2/CH3OH比及反应温度下催化剂性能.当O2/CH3OH=0.2时,催化剂的性能最 佳.在同样条件下, Cu/Zn催化剂对CO的选择性较Cu/Zn/Ni催化剂低,更具优势. Cu/Zn催化 剂用于甲醇部分氧化反应时,甲醇转化率在150 h寿命实验中基本保持在90％左右. XRD谱图 表明Cu/Zn合金的生成是导致Cu/Zn系催化剂在甲醇裂解反应中快速失活的主要原因,而在部 分氧化反应中, O2的存在可抑制Cu/Zn合金的生成,使Cu/Zn催化剂表现出高度的稳定性.     

Size and support effects for the water-gas shift catalysis over gold nanoparticles supported on model Al2O3 and TiO2

The water-gas shift (WGS) reaction rate per total mole of Au under 7% CO, 8.5% CO(2), 22% H(2)O, and 37% H(2) at 1 atm for Au/Al(2)O(3) catalysts at 180 °C and Au/TiO(2) catalysts at 120 °C varies with the number average Au particle size (d) as d(-2.2±0.2) and d(-2.7±0.1), respectively. The use of nonporous and crystalline, model Al(2)O(3) and TiO(2) supports allowed the imaging of the active catalyst and enabled a precise determination of the Au particle size distribution and particle shape using transmission electron microscopy (TEM). Further, the apparent reaction orders and the stretching frequency of CO adsorbed on Au(0) (near 2100 cm(-1)) determined by diffuse reflectance infrared spectroscopy (DRIFTS) depend on d. Because of the changes in reaction rates, kinetics, and the CO stretching frequency with number average Au particle size, it is determined that the dominant active sites are the low coordinated corner Au sites, which are 3 and 7 times more active than the perimeter Au sites for Au/Al(2)O(3) and Au/TiO(2) catalysts, respectively, and 10 times more active for Au on TiO(2) versus Al(2)O(3). From operando Fourier transform infrared spectroscopy (FTIR) experiments, it is determined that the active Au sites are metallic in nature. In addition, Au/Al(2)O(3) catalysts have a higher apparent H(2)O order (0.63) and lower apparent activation energy (9 kJ mol(-1)) than Au/TiO(2) catalysts with apparent H(2)O order of -0.42 to -0.21 and activation energy of 45-60 kJ mol(-1) at near 120 °C. From these data, we conclude that the support directly participates by activating H(2)O molecules.     

Photocatalytic activity of a hierarchically macro/mesoporous titania

Light-harvesting macroporous channels have been successfully incorporated into a mesoporous TiO(2) framework to increase its photocatalytic activity. This bimodal porous material was characterized by X-ray diffractometry in both low-angle and wide-angle ranges, N(2) adsorption-desorption analysis, scanning and transmission electron microscopy, FT-IR, and diffuse reflectance spectroscopy. Ethylene photodegradation in gas-phase medium was employed as a probe reaction to evaluate the photocatalytic reactivity of the catalysts. The results reveal that sintering temperature significantly affects the structural stability and photocatalytic activity of titania. The catalyst which calcined at 350 degrees C possessed an intact macro/mesoporous structure and showed photocatalytic reactivity about 60% higher than that of commercial P25 titania. When the sample was calcined at 500 degrees C, the macroporous structure was retained but the mesoporous structure was partly destroyed. Further heating at temperatures above 600 degrees C destroyed both macro- and mesoporous structures, accompanied by a loss in photocatalytic activity. The high photocatalytic performance of the intact macro/mesoporous TiO(2) may be explained by the existence of macrochannels that increase photoabsorption efficiency and allow efficient diffusion of gaseous molecules.     

电化学方法制备高分散Pt/CMK-3及其对甲醇电化学催化性能

采用直接电化学还原法在介孔碳(CMK-3)载体上直接电沉积高分散的铂纳米颗粒,制备CMK-3复合铂纳米颗粒电极(Pt/CMK-3)。 通过透射电子显微镜分析发现,铂纳米颗粒非常均匀的分布在CMK-3上,平均粒径约5 nm。 通过循环伏安测试,分析了催化剂不同负载铂含量时氯铂酸的利用率,在理论铂质量分数为20%时,这种方法制备的Pt/CMK-3所使用的氯铂酸的利用率最高,在1 mol/L CH3OH+0.5 mol/L H2SO4溶液中循环伏安测试电流密度达到382 A/g。 在相同实验条件下,Pt/CMK-3电极对甲醇电催化活性远高于Pt/XC-72(炭黑)电极和用常规电沉积方法制备的Pt/CMK-3电极。     

以TiO2多孔微球为载体的CuO/TiO2催化剂的制备、表征及CO氧化催化性能

利用高分子反相悬浮聚合技术结合溶胶-凝胶法制备了纳米TiO2晶粒组成的多孔微球. 以TiO2多孔微球为载体, 利用浸渍法制备了CuO/TiO2催化剂, 用示差扫描量热法、热重分析、X 射线衍射和X射线光电子能谱(XPS)对TiO2多孔微球和催化剂进行了表征, 并对其进行了CO催化氧化性能的评价. 结果表明, 于500 ℃焙烧的TiO2多孔微球基本为锐钛矿型结构, 其粒径为19.5 nm. XPS结果表明, 催化剂中载体和活性组分存在相互作用, Cu除了以Cu2+的形式存在外, 还以部分Cu+和Cu0的形式存在. CO催化氧化研究结果表明, 催化剂的催化活性与浸渍液的浓度和催化剂的焙烧温度有关. 用0.5 mol/L Cu(NO3)2·3H2O溶液浸渍得到的催化剂和于200 ℃焙烧得到的催化剂具有较好的催化活性.     

溴代甲烷在TiO2上的光催化降解研究

系统地研究了CH₃Br在溶胶-凝胶法制备的TiO₂催化剂上的气相光催化氧化行为,考察了催化剂煅烧温度、催化剂中残留NO-3、反应物料中的水份、反应温度等催化剂制备及反应条件对催化剂反应性能的影响,并结合XRD、BET比表面积和FTIR等表征结果对TiO₂催化剂的反应行为进行了解释.实验结果表明,CH₃Br在TiO₂上的气相光催化氧化是典型的一级反应,表观活化能为13.7kJ/mol.反应初始阶段存在显著的催化剂失活现象,催化剂高温煅烧,NO-3及水等对该反应活性都有明显的抑制作用,提高反应温度有利于改善催化剂的反应性能.     

Effect of Ti3+ on TiO2-supported Cu catalysts used for CO oxidation

In this paper, we have shown that Cu/TiO(2) catalysts are highly active in CO oxidation. For instance, a 3.4% Cu/TiO(2) catalyst exhibits a higher turnover rate for the effective removal of CO in air than 3-5% Pt/TiO(2) and 20% Cu/ZnO/Al(2)O(3) catalysts. A small amount of Cu(+) species is formed during the calcination treatment at 225 °C, which is the main active phase for the CO oxidation. However, it is proposed that some highly dispersed CuO can also form in the TiO(2) lattice during the calcination treatment. Furthermore, a strong electron interaction between Cu(2+) in highly dispersed CuO and Ti(3+) on rutile TiO(2) (Cu(2+)+Ti(3+)→Cu(+)+Ti(4+)) has been shown to occur. Overall, the reduction of Cu(+) is a major factor that contributes to the reaction rate of the CO oxidation.     

Synthesis of titanium dioxide nanoparticles with mesoporous anatase wall and high photocatalytic activity

Mesoporous titanium dioxide nanosized powder with high specific surface area and anatase wall was synthesized via hydrothermal process by using cetyltrimethylammonium bromide (CTAB) as surfactant-directing agent and pore-forming agent. The resulting materials were characterized by XRD, nitrogen adsorption, FESEM, TEM, and FT-IR spectroscopy. The as-synthesized mesoporous TiO2 nanoparticles have mean diameter of 17.6 nm with mean pore size of 2.1 nm. The specific surface area of the as-synthesized mesoporous nanosized TiO2 exceeded 430 m2/g and that of the samples after calcination at 600 degrees C still have 221.9 m2/g. The mesoporous TiO2 nanoparticles show significant activities on the oxidation of Rhodamine B (RB). The large surface area, small crystalline size, and well-crystallized anatase mesostructure can explain the high photocatalytic activity of mesoporous TiO2 nanoparticles calcined at 400 degrees C.     

How the C-O bond breaks during methanol decomposition on nanocrystallites of palladium catalysts

Experimental findings imply that edge sites (and other defects) on Pd nanocrystallites exposing mainly (111) facets in supported model catalysts are crucial for catalyst modification via deposition of CH(x) (x = 0-3) byproducts of methanol decomposition. To explore this problem computationally, we applied our recently developed approach to model realistically metal catalyst particles as moderately large three-dimensional crystallites. We present here the first results of this advanced approach where we comprehensively quantify the reactivity of a metal catalyst in an important chemical process. In particular, to unravel the mechanism of how CH(x) species are formed, we carried out density functional calculations of C-O bond scission in methanol and various dehydrogenated intermediates (CH3O, CH2OH, CH2O, CHO, CO), deposited on the cuboctahedron model particle Pd79. We calculated the lowest activation barriers, approximately 130 kJ mol(-1), of C-O bond breaking and the most favorable thermodynamics for the adsorbed species CH3O and CH2OH which feature a C-O single bond. In contrast, dissociation of adsorbed CO was characterized as negligibly slow. From the computational result that the decomposition products CH3 and CH2 preferentially adsorb at edge sites of nanoparticles, we rationalize experimental data on catalyst poisoning.     

Preparation of highly active silica-supported Au catalysts for CO oxidation by a solution-based technique

Although Au catalysts can be readily prepared on titania via the deposition-precipitation (DP) method, the direct application of the method similar to the preparation of silica-supported Au catalysts only results in diminished success. This paper reports a novel, efficient method to synthesize highly active Au catalysts supported on mesoporous silica (SBA-15) through a gold cationic complex precursor [Au(en)2]3+ (en = ethylenediamine) via a wet chemical process. The gold cationic precursor was immobilized on negatively charged surfaces of silica by a unique DP method that makes use of the deprotonation reaction of ethylenediamine ligands. The resulting mesoporous catalyst has been demonstrated to be highly active for CO oxidation at room temperature and even below 273 K, the activity of which is much superior to that of silica-supported Au catalysts previously prepared by various solution techniques. The pH value of the gold precursor solution plays a key role in determining the catalytic activity through the regulation of [Au(en)2]3+ deprotonation reaction and the surface interaction of silica with the gold precursor. This mesoporous gold silica catalyst has also been shown to be highly resistant to sintering because of the stabilization of Au nanoparticles inside mesopores.     

Photo-catalytic oxidation of cyclohexane over TiO2: a novel interpretation of temperature dependent performance

The rate of cyclohexane photo-catalytic oxidation to cyclohexanone over anatase TiO(2) was studied at temperatures between 23 and 60 °C by in situ ATR-FTIR spectroscopy, and the kinetic parameters were estimated using a microkinetic model. At low temperatures, surface cyclohexanone formation is limited by cyclohexane adsorption due to unfavorable desorption of H(2)O, rather than previously proposed slow desorption of the product cyclohexanone. Up to 50 °C, the activation energy for photocatalytic cyclohexanone formation is zero, while carboxylates are formed with an activation energy of 18.4 ± 3.3 kJ mol(-1). Above 50 °C, significant (thermal) oxidation of cyclohexanone contributes to carboxylate formation. The irreversibly adsorbed carboxylates lead to deactivation of the catalyst, and are most likely the predominant cause of the non-Arrhenius behavior at relatively high reaction temperatures, rather than cyclohexane adsorption limitations. The results imply that elevating the reaction temperature of photocatalytic cyclohexane oxidation reduces selectivity, and is not a means to suppress catalyst deactivation.     

Water-medium and solvent-free organic reactions over a bifunctional catalyst with Au nanoparticles covalently bonded to HS/SO3H functionalized periodic mesoporous organosilica

An operationally simple approach for the preparation of a new class of bifunctional Au nanoparticle-acid catalysts has been developed. In situ reduction of Au(3+) with HS-functionalized periodic mesoporous organosilicas (PMOs) creates robust, fine Au nanoparticles and concomitantly produces a sulfonic acid moiety strongly bonded to PMOs. Characterizations of the nanostructures reveal that Au nanoparticles are formed with uniformed, narrow size distribution around 1-2 nm, which is very critical for essential catalytic activities. Moreover, the Au nanoparticles are mainly attached onto the pore surface rather than onto the outer surface with ordered mesoporous channels, allowing for maximal exposure to reaction substrates while minimizing Au nanoparticle leaching. Their higher S(BET), V(P), and D(P) than either the Au-HS-PMO(Et) or the Au/SO(3)H-PMO(Et) render the catalyst with comparably even higher catalytic efficiency than its homogeneous counterparts. Furthermore, the unique amphiphilic compartment of the Au-HS/SO(3)H-PMO(Et) nanostructures enables organic reactions to proceed efficiently in a pure aqueous solution without using any organic solvents or even without water. As demonstrated experimentally, remarkably, the unique bifunctional Au-HS/SO(3)H-PMO(Et) catalyst displays higher efficiencies in promoting water-medium alkyne hydration, intramolecular hydroamination, styrene oxidation, and three-component coupling reactions and even the solvent-free alkyne hydration process than its homogeneous catalysts. The robust catalyst can be easily recycled and used repetitively at least 10 times without loss of catalytic efficiency. These features render the catalyst particularly attractive in the practice of organic synthesis in an environmentally friendly manner.     

Comparison of electrode structures and photovoltaic properties of porphyrin-sensitized solar cells with TiO2 and Nb, Ge, Zr-added TiO2 composite electrodes

Electrode structures and photovoltaic properties of porphyrin-sensitized solar cells with TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were examined to disclose the effects of partial substitution of Ti atom by the other metals in the composite electrodes. The TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were prepared by sol-gel process using laurylamine hydrochloride as a template for the formation of micellar precursors yielding well-defined mesoporous nanocrystalline structures, as in the cases of the formation of silica and titania tubules and nanoparticles by the templating mechanism. The TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were characterized by transmission electron microscopy, BET surface area analysis, X-ray diffraction analysis, Raman spectroscopy, and impedance measurements. The TiO2 anatase nanocrystalline structure is retained after doping a small amount (5 mol %) of Nb, Ge, or Zr into the TiO2 structure, suggesting the homogeneous distribution of the doped metals with replacing Ti atom by the doped metal. The power conversion efficiency of the porphyrin-sensitized solar cells increases in the order Zr-added TiO2 (0.8%) < Nb-added TiO2 (1.2%) < TiO2 (2.0%) < Ge-added TiO2 cells (2.4%) under the same conditions. The improvement of cell performance of the Ge-added TiO2 cell results from the negative shift of the conduction band of the Ge-added TiO2 electrode. The Ge-added TiO2 cell exhibited a maximum power conversion efficiency of 3.5% when the porphyrin was adsorbed onto the surface of the Ge-added TiO2 electrode with a thickness of 4 microm in MeOH for 1 h.     

Photocatalytic activity of structured mesoporous TiO2 materials

Starting from colloidal TiO2 nanoparticles in combination with tetraethyl orthosilicate using neutral Pluronic or cationic cetyltrimethylammonium as templates, a series of structured mesoporous silicas has been obtained. The structure of the mesoporous titania was confirmed by isothermal gas adsorption, transmission electron microscopy, and X-ray diffraction. The pore diameter ranged between 3.8 and 10.9 nm, and the BET surface area varied from 99 to 584 m2 g(-1). The photocatalytic activity of these samples for the degradation of phenol in aqueous solution has been compared with that of standard P-25 TiO2. Even though the activity of these new mesostructured materials is lower that those found for P-25 TiO2, the turnover frequency of the photocatalytic activity (moles of phenol degraded per Ti atom present at initial reaction time) is much higher for the mesoporous titania, particularly with low titanium contents for those materials (mpTiO2-5 and TiO2SBA15-5).     

Preparation and characterization of vanadium oxide deposited on thermally stable mesoporous titania

Vanadium oxide was deposited on mesoporous titania by the molecular designed dispersion method to investigate the potential properties of these catalysts. Mesoporous titania was synthesized following the evaporation-induced self-assembly (EISA) method with a subsequent treatment with ammonia to increase the thermal stability. As a result, the mesoporous titania obtained shows a high surface area (approximately 350 m2/g) and high stability. Vanadium oxide was deposited by the MDD method using a vanadyl acetylacetonate complex that was transformed into VOx after a controlled calcination in air flow at 300 degrees C. The mesostructure and porosity characteristics of titania remain even until the maximum V-loading was reached (0.4 mmol/g), as it was shown by N2 sorption measurements at -196 degrees C. The catalysts were characterized by chemical analysis, Fourier transform infrared-photoacoustic spectroscopy (FTIR-PAS), UV-vis diffuse reflectance (DR), and Fourier transform Raman spectroscopy. Raman spectra showed isolated V species for the different V-containing catalysts. Furthermore, UV-vis-DR revealed a higher contribution of polymeric species as the V loading increases. The VOx/mesoporous titania catalysts were highly active in the selective catalytic reduction of NOx. A high activity in the NO conversion was observed, which increases with increasing metal loading.     

Influence of Excitation Wavelength (UV or Visible Light) on the Photocatalytic Activity of Titania Containing Gold Nanoparticles for the Generation of Hydrogen or Oxygen from Water

Gold nanoparticles supported on P25 titania (Au/TiO(2)) exhibit photocatalytic activity for UV and visible light (532 nm laser or polychromatic light λ > 400 nm) water splitting. The efficiency and operating mechanism are different depending on whether excitation occurs on the titania semiconductor (gold acting as electron buffer and site for gas generation) or on the surface plasmon band of gold (photoinjection of electrons from gold onto the titania conduction band and less oxidizing electron hole potential of about -1.14 V). For the novel visible light photoactivity of Au/TiO(2), it has been determined that gold loading, particle size and calcination temperature play a role in the photocatalytic activity, the most active material (Φ(H2) = 7.5% and Φ(O2) = 5.0% at 560 nm) being the catalyst containing 0.2 wt % gold with 1.87 nm average particle size and calcined at 200 °C.