负载铯催化剂上苯酚与甲醇醚化制苯甲醚

研究了不同酸碱中心、载体、前躯体和负载量对负载铯催化剂上苯酚与甲醇醚化制苯甲醚反应行为的影响。结果表明,碱性中心比酸性中心具有更高的苯甲醚选择性,碱性中心的阳离子影响催化剂的苯甲醚选择性。载体影响铯离子的电子结合能,从而影响催化剂的醚化活性;铯离子的电子结合能越低,催化剂醚化活性越低;载体影响催化剂强碱性位数量,从而影响苯甲醚选择性;强碱性位数量越多,副反应越容易发生,苯甲醚选择性越低。不同前躯体制备的Cs/Si O2由于表面相对铯原子数量不同而活性不同;Cs/Si O2的单层负载量为1.0 mmol/g,超过单层负载量后催化剂的平均活性显著下降。     

Mechanism of Aniline Methylation on Zeolite Catalysts Investigated by In Situ 13C NMR Spectroscopy

The alkylation reaction of aniline with methanol on zeolites HY and CsOH/CsNaY was studied by in situ ¹³C NMR spectroscopy under flow and batch conditions. Attention was focused on the identification of intermediates and on the determination of the formation mechanisms of N-methylaniline, N,N-dimethylaniline, and toluidines. To refine the main steps of the reaction, the transformations of the following individual compounds and intermediates, which were detected in the course of alkylation, were studied: dimethyl ether, surface methoxy groups, methylanilinium ions, formaldehyde, and N-methyleneaniline. It was found that N-methylaniline and N,N-dimethylaniline were formed as a result of aniline methylation by methanol dehydration products (methoxy groups or dimethyl ether) on acidic zeolites or as a result of alkylation by formaldehyde or methoxy groups on basic zeolites. Toluidines were formed by the isomerization ofN-methylanilinium ions, which were produced only on acidic zeolites, rather than by the direct alkylation of aniline.     

苯酚和草酸二甲酯在不同分子筛催化下的酯交换反应

研究了以TS－1、H－ZSM－5、Hβ和H－丝光沸石等不同分子筛为催化剂，苯酚和草酸二甲酯酯交换合成草酸二苯酯反应。通过对催化剂进行吸附吡啶的红外光谱和NH3－TPD表征，考察了不同分子筛催化剂的酸性和酸强度对草酸二苯酯合成反应的影响，确定了催化剂上的弱酸中心是催化苯酚和草酸二甲酯酯交换合成草酸二苯酯反应的活性位，且催化剂的酸性中心越多，酸量越大，催化活性越好。催化剂上的强酸中心促进了副产物苯甲醚的生成。     

HZSM-5沸石分子筛上苯酚与甲醇的烷基化反应

 在n（PhOH）／n（CH3OH）＝1,WGSV＝0．5h－1,T＝673K的反应条件下,研究了HZSM－5,HZSM－23和改性HZSM－5分子筛上苯酚与甲醇烷基化反应的规律．结果表明,分子筛外表面的酸中心对苯酚烷基化反应的贡献较大．用4－甲基喹啉使分子筛外表面的酸中心中毒后,影响反应产物选择性的主要因素是分子筛的孔径．孔径较小的HZSM－23分子筛对提高芳香醚的选择性,抑制二甲酚的生成和提高对甲酚的选择性有利．间甲酚和二甲酚可以在HZSM－5沸石的孔道内生成,但在HZSM－23的孔道内受到抑制．用P2O5,MgO和Sb2O3对HZSM－5改性都可以提高芳香醚的选择性,降低甲酚和二甲酚的选择性．随着氧化物负载量的增加,邻甲酚选择性升高．适度的氧化物改性可以提高对甲酚的选择性,改性效果为Sb2O3＞P2O5＞MgO．     

The composition of catalysts prepared from tri-n-propylaluminum,anisole, and titanium tetrachloride

Catalysts were prepared from titanium tetrachloride and tri-n-propylaluminum or tri-n-propylaluminum anisole at [Al]/[Ti] molar ratios of 0.20–1.10. They were aged and filtered, and the solid and liquid portions were analyzed for aluminum, titanium, chlorine, and certain organic constituents. The analyses indicate that the solid of the nonetherate catalyst is predominantly TiCl₃, some AlCl₃ or aluminum alkyl chlorides being included. Only at [Al]/[Ti] = 1.10 was any alkyl group found in the solid. The same general results were found for the etherate catalyst, but the solid had a somewhat lower [Cl]/[Ti] ratio, indicating greater reduction or alkylation, or both, of the titanium species than in the nonetherate catalyst. The solid also contained some anisole at the higher [Al]/[Ti] ratios. The results lend general support to proposed reactions for the catalyst formation. The main differences in the etherate catalysts relative to the non-etherate system, particularly at the higher [Al]/[Ti] ratios, are the apparently greater reduction or alkylation of the titanium in the solids, the presence of anisole in the liquid and solid portions, and the presence of phenol in the liquid portion. The phenol presumably comes from cleavage of the anisole during the catalyst formation. Not all of the anisole has been accounted for in a materials balance, nor has all of the chlorine in the etherate catalysts. No propyl or isopropyl chloride was found in the catalysts; there is no significant amount of polypropylene in any of the catalyst solids. Hence the fate of the alkyl groups remains undetermined at present.     

AlPO4?Al2O3 catalysts with low alumina content, VII. Anisole conversion in the presence of methanol

The conversion of anisole in the presence of methanol (anisole/methanol molar ratio=4) over AlPO₄–Al₂O₃ (5–15 wt.% Al₂O₃) catalysts gave a mixture of dealkylated and C-alkylated products (C-alkylation preferentially inortho-position) in which dealkylation to phenol always predominated. The catalytic activity, which increased with alumina content and decreased on increasing the calcination temperature from 773 to 1073 K, was fairly well related to the change in surface acidic characteristics. Furthermore, anisole conversion followed the requirements of the Bassett-Habgood kinetic treatment for first order processes, with a single common interaction mechanism and, consequently, a common transition state for all catalysts. Poisoning by pyridine and 2,6-dimethylpyridine confirmed that anisole conversion occurs on acid sites.     

Dehydration of methanol to dimethyl ether over modified vermiculites

Vermiculite materials pillared with alumina and modified with titanium were tested as catalysts for methanol dehydration to dimethyl ether. The different samples were characterized by powder XRD, TG, nitrogen adsorption, and pyridine adsorption followed by FTIR. Catalytic activity was evaluated in the temperature range 250–450 °C using different hourly space velocities, in the absence and in the presence of water in the feed. Modified vermiculites were shown to be active and selective in methanol dehydration. Al pillaring was found to result in more active catalysts than in the case of the modification with TiO₂. The influence of methanol hourly space velocity did not have a significant effect on methanol conversion, but it changed drastically selectivity to dimethyl ether at the beginning of the reaction. The addition of water had a negative effect on the catalysts’ activity and led to a faster catalyst deactivation.     

Cu-Fe-MgO/AlPO_4-5对甲醇水蒸气重整制氢的催化性能研究

以AlPO_4-5分子筛为载体,采用浸渍法制备Cu-Fe-MgO/AlPO_4-5催化剂,用于催化甲醇和水蒸气重整反应制氢气。采用XRD、N2吸附-脱附、H2-TPR、CO2-TPD和NH3-TPD等对催化剂进行表征。结果表明,加入Fe可以明显提高甲醇的转化率,但副产物二甲醚的选择性也增加,添加MgO对降低二甲醚具有明显的作用,但不能提高甲醇的转化率。AlPO_4-5负载Cu、Fe和MgO的质量分数分别为15%、6%和1%时具有较高的催化活性,在反应温度300℃、水醇物质的量比为1.1∶1和质量空速2.51 h~(-1)的条件下,对甲醇的转化率为93.08%,二氧化碳和氢气的选择性分别为95.80%和96.93%,对副产物一氧化碳和二甲醚的选择性分别为1.70%和2.51%。表征结果表明,Cu-Fe-MgO/AlPO_4-5同时含有弱酸弱碱和强酸强碱中心,适量的MgO增加了强碱中心的量,降低弱酸中心的强度,但对强酸中心影响不大。     

Alkylation of phenol with dimethyl carbonate over AlPO4, Al2O3 and AlPO4-Al2O3 catalysts

The vapor-phase catalytic alkylation of phenol with dimethyl carbonate over different AlPO₄ (Al/P=1), Al₂O₃ and AlPO₄-Al₂O₃ (5–25 wt.% Al₂O₃) catalysts produces anisole (O-alkylation) as the major reaction product althougho-cresol (C-alkylation) and methylanisoles were also found. The reaction is first order in phenol while O-and C-alkylation follow parallel processes. As compared with methanol, DMC is far more effective as a methylating agent, and the methylation proceeds at a lower temperature and with higher O-alkylation selectivity.     

The effect of FER zeolite acid sites in methanol-to-dimethyl-ether catalytic dehydration

In this paper, the effect of acidity of zeolites with FER framework was studied in the methanol dehydration to dimethyl ether reaction, by comparing catalysts with different Si/Al ratios(namely 8, 30 and60). The aim of this work was to investigate how the acid sites concentration, strength, distribution and typology(Br?nsted and Lewis) affect methanol conversion, DME selectivity and coke formation. It was found that the aluminium content affects slightly acid sites strength whilst a relevant effect on acid sites concentration and distribution(Br?nsted/Lewis) was observed as 24% of Lewis sites were found on Alrichest samples, whilst less than 10% of Lewis acid sites were observed on FER at higher Si/Al ratio. All the investigated catalyst samples showed a selectivity toward DME always greater than 0.9 and samples with the lowest Si/Al ratio exhibit the best performances in terms of methanol conversion, approaching the theoretical equilibrium value(around 0.85) at temperatures below 200 °C. Turnover-frequency analysis suggests that this result seems to be related not only to the higher amount of acid sites but also that the presence of Lewis acid sites may play a significant role in converting methanol. On the other hand, the presence of Lewis acid sites, combined with a high acidity, promote the formation of by-products(mainly methane) and coke deposition during the reaction. As final evidence, all the investigated catalysts exhibit very high resistance to deactivation by coke deposition, over 60 h continuous test, and a GC–MS analysis of the coke deposited on the catalyst surface reveals tetra-methyl benzene as main component.     

氧化铝负载催化剂作用下以甲醇为烷基化试剂的苯酚气相转化制备苯甲醚(英文)

苯甲醚作为重要的化学品和医药中间体而广泛应用于香料、调味剂及有机合成.液相法是传统的苯甲醚制备工艺,例如在碱性环境下,通过酚钠与硫酸二甲酯反应,溴苯与甲醇反应,酚钠与氯代甲烷反应均可制得苯甲醚.然而,这些方法具有环境处理负担较重和所用原料毒性较强等不足而备受限制.因此,环境友好的绿色苯甲醚合成工艺的开发成为必然,苯酚的气相烷基化工艺由此提出.其中,以碳酸二甲酯(DMC)为烷基化试剂的苯酚气相转化苯甲醚制备方法最受关注.DMC是常用的绿色高效烷基化试剂,但其价格相对较高,在一定程度上增加了苯甲醚制备工艺的复杂性和产品成本.鉴于DMC可由甲醇经氧化羰基化制得,因此以甲醇为烷基化试剂的苯酚气相烷基化转化制备苯甲醚方法成为另一研究热点.然而,与DMC的烷基化性能相比,以甲醇为烷基化试剂的反应产物分布较为复杂,作为苯酚O-烷基化(在苯酚的羟基氧原子上发生的烷基化)产物的苯甲醚相对较难获得,而苯酚的C-烷基化(在苯酚的芳环上发生的烷基化)产物甲基酚产率更易提高.总体而言,与DMC烷基化方法相比,以甲醇为烷基化试剂的苯酚气相转化制备苯甲醚方法有待改善,相关反应机理也更欠明晰,因此具有重要的研究价值.本文研究了γ-Al_2O_3(AA)负载型催化剂上以甲醇为烷基化试剂的苯酚气相转化制备苯甲醚方法,考察了反应温度、气体空速、苯酚与甲醇配比以及催化剂中K负载量和焙烧温度等对反应性能的影响,并分析了该体系中的反应机理.研究表明,在AA上负载的8种化合物(NaCl,MgCl_2,Fe_2(SO_4)_3,Co(NO_3)_2,ZnCl_2,La(NO_3)_3,Ce(NO_3)_3和KH_2PO_4)的催化剂中,KH_2PO_4/AA的催化性能最佳,相应催化剂中K离子负载量为7.53 wt%,于700 oC焙烧8 h.苯酚与甲醇气相反应过程中,苯甲醚最大收率出现在400–450 oC,且随甲醇与苯酚的摩尔比升高而增加,但随空速的提高而降低.另外,在KH_2PO_4/AA催化剂的高K含量,以及低温、高空速、低甲醇含量的物料配比的条件下,对苯酚的O-烷基化过程有利.产物除主产物苯甲醚以外,还有少量甲基苯酚、甲基苯甲醚以及二甲基苯酚等副产物.在K含量为7.53 wt%的KH_2PO_4/AA催化剂作用下,苯甲醚收率最高时反应条件为400–450 oC,空速小于0.18 h儃1,甲醇与苯酚摩尔配比为5.本文所开发的催化剂制备方法简单,反应条件温和,产物收率较高,因此具有较好的应用前景.X射线衍射结果显示,经高温焙烧及固相反应后,KH_2PO_4/AA催化剂中产生了K_3Al_2(PO_4)_3新物相.推测该反应机理是酸性氧化铝促进甲醇脱羟基负离子以及K离子促进酚羟基脱氢质子,所形成的甲基正离子进一步与苯氧基负离子结合得到苯甲醚的"钾离子-酸"双功能催化作用过程     

Phenol methylation over CrPO4 and CrPO4?AlPO4 catalysts

The vapor-phase catalytic alkylation of phenol with methanol and dimethyl carbonate on a series of differently prepared CrPO₄ (Cr/P=1) and CrPO₄-AlPO₄ (CrAIP) catalysts, has been studied at different temperatures (473–673 K). The reaction is first order in phenol, giving a mixture of O- and C-alkylated products (C-alkylation taking place preferentially at theortho-position). Moreover, dimethyl carbonate is a better methylating agent than methanol.     

甲苯甲醇侧链烷基化反应中甲酸盐的形成及其作用

将碱金属碳酸盐修饰的KX和NaY沸石用于催化甲苯甲醇侧链烷基化反应,并结合甲醇吸附的红外光谱以及异丙醇和甲醇催化分解反应结果,剖析了甲酸盐的形成及其作用.结果表明,碱金属碳酸盐的负载能提高碱金属离子交换八面沸石的催化活性.在反应过程中催化剂表面形成了不同数量的甲酸盐,尤其是K2CO3修饰的KX上;甲酸盐主要来源于碳酸盐与甲醇分解产物甲醛的反应,它的形成对催化剂甲苯甲醇侧链烷基化活性的影响较大,类似于碱金属硼酸盐的修饰,改善了催化剂的表面酸碱性,形成了更为有效的活性中心.     

Conversion of anisole in the presence of methanol over AlPO4?Al2O3 catalysts modified with fluoride and sulfate anions

The gas-phase microcatalytic conversion of anisole in the presence of methanol (methanol/anisole molar ratio=4) was studied at temperatures ranging from 523 to 673 K over anion treated (1–3 wt.% F or SO ₄ ^2– ) AlPO₄–Al₂O₃ (25 wt.% Al₂O₃) catalysts. Anisole conversion gave a mixture of dealkylated and C-alkylated products (C-alkylation preferentially in ortho-position) where dealkylation always predominates. The influences of the reaction temperature and both anion type and anion loading upon the conversion of anisole and the selectivities of the products were investigated. The higher increase in surface acidity by fluoride loading increases both the C-alkylation selectivity (mainly to 2-methylanisole) and dealkylation to phenol; so that a lower anisole conversion (smaller pseudokinetic constant) and higher methylanisoles selectivity is found for APAI-P-F catalysts related to unmodified one.     

微量吸附量热技术在ZnxCo1-xCr2O4催化剂筛选上的应用

采用共沉淀法制备了一系列ZnxCo1-xCr2O4催化剂,并将其进行了微量吸附量热技术测定,及苯酚与甲醇邻位烷基化反应的应用性实验。结果证明,ZnxCo1-xCr2O4催化剂上苯酚和甲醇邻位烷基化反应的活性中心应是酸碱的协同作用产生的,ZnxCo1-xCr2O4系列催化剂中的Zn／Co的最佳比例为Zn／Co=1。运用微量吸附量热技术实现了对ZnxCo1-xCr2O4系列催化剂的优化。     

Catalytic alkylation of pyridine and its homologs. Preparation of 3, 5-lutidine and 3-isopropylpyridine

When the catalytic alkylation of pyridine was carried out with methanol and dimethyl ether under high-pressure conditions the main product was 3, 5-lutidine. In the alkylation of 3-picoline with methanol, the main product was 3-isopropylpyridine.     

Ortho‐Alkylation of Phenol with Methanol Using Pb‐Cr Promoted Magnesium Oxide Catalysts

In this study, Pb‐Cr promoted magnesium oxide catalysts were used to catalyze the ortho‐alkylation of phenol in the presence of excess methanol. The Cr/MgO catalyst exhibited a high conversion of phenol and a relatively high selectivity for the ortho‐alkylation of phenol. The catalytic activity and the stability of Cr/MgO were improved by the addition of a fairly small amount of Pb. The Pb‐Cr/MgO catalyst showed specificity for the ortho‐alkylation of phenol, which was proved by a series of phenol derivative reactions with methanol.     

改性H-MOR沸石催化甲醇转化(英文)

The conversion of methanol was carried out over various mordenite zeolite catalysts to evaluate their catalytic performance. A post-preparation treatment of the H-MOR catalyst by halogenation with NH4Cl or NH4F and by hydrohalogenation with HCl or HF was carried out and its effect on methanol conversion reactions at 100–300 °C in a continuous flow reactor was investigated. The as-synthesized Hmordenite (H-MOR) is generally more active during dimethyl ether (DME) production than the NH4-MOR and Na-MOR. Fluor...     

超临界流体状态下的异构烷烃与烯烃烷基化反应

成功地应用固体酸催化剂在超临界反应条件下进行了异构烷烃与丁烯的烷基化反应。在超临界反应条件下,固体酸催化剂在１４００ｈ的反应以后,仍保持１００％的烯烃转化率。探索出一个解决固体酸催化剂在烷基化反应中极易失活的有效方法。探讨了超临界流体抑制固体酸催化剂结炭失活的机制和烷基化反应中选择超临界反应条件的规律。     

同位素示踪研究K2CO3/CH3I促进的碳酸二甲酯直接合成反应

 采用同位素示踪技术,系统地研究了K2CO3/CH3I促进的CO2插入甲醇直接合成碳酸二甲酯(DMC)的反应机理. 结果表明,固体碱碳酸钾催化剂直接参与了DMC的合成过程, DMC分子中的羰基由CO2插入甲醇后形成,两个甲基分别来源于甲醇和碘甲烷. 本文将以往文献中提出的DMC生成机理和二甲醚生成机理结合起来,并对其进行适当补充后,可以很好地解释实验结果.