梯形介质膜光栅衍射特性分析

基于严格耦合波理论建立了梯形介质膜光栅的衍射机理模型,利用该模型讨论了底角为70°的梯形介质膜光栅-1级的衍射行为.通过对梯形介质膜光栅的占空比、槽深和剩余厚度的优化,设计了应用于1053 nm和51.2°角度入射的梯形介质膜光栅.对于顶层为HfO2的介质膜光栅,当槽深为200 nm,剩余厚度为100 nm,占空比为0.35时.其衍射效率优于99.5%,而对于顶层为SiO2的梯形光栅,为获得99.5%的衍射效率.其槽深为800 nm,剩余厚度为320 nm.而且,获得同样的衍射效率,顶层为HfO2的梯形光栅具有更宽的光谱特性.数值计算表明,严格耦合波理论模型对梯形介质膜光栅衍射效率的计算具有很好的收敛性和稳定性.     

二元矩形金属光栅衍射增强电磁理论

采用耦合波原理计算了TM波经过二元纳米量级金属光栅衍射的电磁场，研究了金属光栅的占空比、光栅深度及TM波入射角对衍射后的光栅表面电磁场的增强的影响，针对金属金、银做了探讨和分析，得出重要的结论. 关键词： 耦合波原理 金属光栅 衍射     

大功率分布反馈激光器中光栅优化及试验

对于分布反馈激光器来说，光栅的耦合系数是一个重要参数. 利用改进的耦合波理论计算了具体器件结构中光栅形貌对二级光栅耦合系数的影响. 在此基础上制作的器件功率达到了单面50 mW，边模抑制比为36 dB. 关键词： DFB激光器 耦合波理论 二级光栅 边模抑制比     

用耦合波方法研究取样光栅的衍射特性

介绍了利用耦合波理论编写计算光栅衍射特性程序的基本思想和主要步骤.利用编写的程序计算并分析了一种用于激光取样光栅TE波和TM波的衍射特性.     

体光栅耦合波理论中的能量平衡

基于对体光栅衍射效率的计算分析,本文直接地、精细地讨论了体光栅的功率守恒问题.结果指出:弱耦合前提假定下的双波耦合波二阶理论,不能严格地满足能量平衡准则.     

用于ICF的分频光栅的耦合波分析

用严格的耦合波理论分析用于分频的闪耀光栅验证标量理论结果的实用性.计算结果同标量理论结果进行比较表明,在提高光栅分辨力的现有指标情况下,闪耀光栅具有良好的分频效果.并同时给出了严格的耦合波理论中的截断误差对最终结果的影响.     

周期介质膜压缩光栅中的导模共振效应

 使用耦合波法以及特征矩阵法计算了周期膜堆结构以及介质压缩光栅的本征值，研究了介质型压缩光栅产生导模共振现象的条件，并计算了导模共振点附近光栅的衍射效率曲线。针对导模共振效应对光栅应用的影响，提出了一种避开该效应的方法。计算结果表明：当介质折射率呈周期变化时，取光栅周期为0.667 μm，深度为0.6 μm时，可以避开导模共振效应。     

用一种矩阵计算方法分析体积全息光栅

本文在用于分析体积全息光栅衍射特性的法布里珀罗腔理论模型的基础上,利用矩阵法计算并分析了体积全息光栅的衍射特性.基于该理论模型的数值模拟结果与耦合波理论和以前的实验结果能较好地符合.     

基于FDTD方法的光栅结构光谱特性研究

基于时域有限差分(FDTD)法,从麦克斯韦方程组出发,结合周期边界条件将完全匹配层SAC-PML吸收边界条件应用到所建立的光栅数值模型中.对光栅结构和光滑表面结构的光谱特性进行了数值计算,得到了TM波入射时结构的吸收率,讨论了金属光栅耦合的表面等离子极化(SPPs)和空腔谐振模(Microcavity Mode)现象....     

π相移光纤光栅水听器的超声波传感指向特性

π相移光纤光栅因具有较短的有效光栅传感长度,近年来成为了超声传感领域的研究热点.本研究旨在探究π相移光纤光栅作为水听器应用时对超声波的指向性特性.选取π相移光纤光栅作为超声传感单元,先基于分层介质的声传播理论计算出水中超声波入射时光纤纤芯的应变,再运用基于光学耦合模方程的传递矩阵法计算反射光谱得到光波长偏移.将角度-频率空间分为三个区域,计算了声波频率在1—10 MHz时不同角度下的应变结果和光波长偏移响应特性,并开展了实验研究.结果表明,理论和实验结果具有较高的一致性,π相移光纤光栅在超声波垂直光纤入射时响应最大,随声波入射方向与光纤法向间夹角的增加,π相移光纤光栅的声响应先急剧下降,后在水中直达声波和光纤中导波叠加时出现极大值.此外,π相移光纤光栅的声响应随声波频率增加而降低.本研究对π相移光纤光栅在超声传感中的实际应用具有重要意义.     

Metal-mirror-based grating for high-efficiency element in dense wavelength division multiplexing

It is desirable to obtain high efficiency with polarization-independence and wideband properties for incident wavelength. A metal-mirror-based grating is presented to diffract the incident wave into reflection orders with high efficiency for TE and TM polarization. The modal method and rigorous coupled-wave analysis (RCWA) are used together to optimize a metal-mirror-based grating effectively. From the analysis of the modal method, it is feasible to realize such a grating with the prescribed grating duty cycle and period. Accurate parameters of the grating depth and thickness of the connecting layer are optimized using RCWA. Compared with the reported binary simple grating, high efficiency can be improved greatly for the incident wavelength of 1550 nm in dense wavelength division multiplexing. The diffraction investigation indicates that a wideband property for incident wavelength can be obtained for such a novel metal-mirror-based grating.     

共振域矩形介质光栅的逆向设计

采用模态法研究了共振域光栅分束器及闪耀光栅等光学器件的设计原理及逆向设计方法,给出了-1级非偏振闪耀光栅的典型设计示例。研究表明,自准直角入射时,光束在光栅内传输将激发产生离散模,通过调节离散模透过光栅传输时的累积相位差,可对衍射光进行调控,实现偏振(非偏振)分束、偏振(非偏振)闪耀等功能。采用严格耦合波法对基于模态法逆向设计的-1级非偏振石英闪耀光栅的几何参数进行验证,计算结果显示两者非常吻合,证明了该方法的正确性。     

Unified design of wavelength-independent deep-etched fused-silica gratings

We present a unified design of wavelength-independent deep-etched fused-silica gratings as polarizing beam splitters and polarization-independent two-port beam splitters by using the simplified modal method. By defining unified grating parameters as the ratio of incident wavelength to grating period and the ratio of groove depth to grating period, unified grating structures are found to be approximately wavelength-independent, which is based on the modal view of the accumulated phase difference of two excited propagating grating modes. Diffraction efficiencies given by the rigorous coupled-wave analysis (RCWA) verified this unified design at the wavelength of 1064 nm. It should be noted that this unified design of wavelength-independent gratings is an analytic result, which is impossible to be derived with the well-known numerical RCWA. Modal method is powerful and presents a clear physical picture for us to obtain this unified design. Therefore, this unified design can be used as a general guideline for designing deep-etched fused-silica gratings as beam splitters for practical applications from ultraviolet to near infrared.     

高密度相位光栅的偏振选择性

高密度光栅具有与传统光栅不同的性质,其衍射特性往往是偏振相关的。本文针对1550nm波长TE/TM偏振入射光和0.5的光栅占空比,利用严格耦合波分析数值计算了不同光栅周期下0级及-1级的衍射效率。研究表明,相比周期为1550nm的光栅,当周期为1200nm时,偏振相关衍射效应明显增强,当光栅周期为890nm时,TE偏振光的衍射效率随着光栅深度呈正余弦变化,而TM偏振光的衍射效率始终集中在0级,具有偏振选择性。通过模式方法,利用模式中的有效折射率概念,研究了不同周期下被入射光所激发的两种光波模式通过光栅区域传播所累积的相位差;基于双光束干涉,模拟了0级和-1级的衍射效率。结果表明,利用严格耦合波分析的数值计算结果符合模式方法的理论预期,对于高密度相位光栅的偏振选择性给予了合理的物理机制解释。     

Modal analysis of deep-etched low-contrast two-port beam splitter grating

Modal analysis of a deep-etched low-contrast two-port beam splitter grating under Littrow mounting is presented. The guideline for the design of a subwavelength transmission fused-silica phase grating as high-efficiency grating, polarizing beam splitter (PBS), and two-port beam splitter, is summarized. As an example, a polarization-independent two-port beam splitter grating is designed at wavelength of 1064 nm. We firstly analyzed the physical essence of the grating by the simplified modal method. The guideline for the grating design and the approximate grating parameters are obtained. Then using the rigorous coupled-wave analysis (RCWA) with parameters varying around the approximate ones, optimum grating parameters can be determined. With the design guideline, the time for the rigorous calculation of the grating profile parameters can be reduced significantly.     

Color filter based on a submicrometer cascaded grating

A color filter incorporating a submicrometer cascaded grating was proposed. The device was analyzed by the rigorous coupled-wave analysis (RCWA) and consisted of three parts: a substrate, a ZnS grating and an Al grating. Three different devices with the full width at half-maximum (FWHM) of ∼100 nm and the peak transmission of more than 70% are designed based on the transmission characteristics under different structural parameters. Compared to the previous color filters incorporating a grating, the numerical results show that the transmission efficiency increases of more than 13% and the overlap of the tricolor output spectra decreases effectively.     

多层介质膜光栅用高反射镜的严格耦合波分析

基于严格耦合波和增强透射矩阵的方法,提出了一种数值稳定的求解多层介质膜光学特性的机理模型.利用该模型计算了多层介质膜光栅用高反射镜的优化设计膜系.使用电子束热蒸发方式制备的多层介质膜光谱特性和理论设计的结果符合得很好,该严格耦合波模型是分析介质膜光学特性有效的稳定的数值求解方法.     

Analysis of Near-Field Intensity Distributions of High-Compression Talbot Array Illuminators Using Rigorous Diffraction Theory

The technology nowadays employed in the field of binary optics allows a relatively easy fabrication of grating structures down to the wavelength region. The analysis of light propagation through such grating structures requires the use of rigorous diffraction theories such as the rigorous coupled-wave analysis (RCWA), in order to take proper account of polarization effects in the electric and magnetic field and the thickness of the grating. In this paper, we examine the near-field intensity distributions and associated illumination efficiencies of Talbot array illuminators (TAIL#x0027;s) with compression ratios of 8 and 16 using RCWA. The high illumination efficiency observed close to the grating surface is expected to bring about new applications of TAIL#x0027;s in the field of super-resolution and near-field optics.This paper was originally presented at the 2nd International Conference on Optical Design and Fabrication, ODF2000 which was held on November 15-17, 2000 at the International Conference Center, Tokyo, Waseda University, Japan.     

滑动盖板对一维微尺度光栅红外辐射特性影响

电磁波入射到微尺度周期性结构表面时,一定条件下将在某一波段产生异常光吸收现象。基于该特性,本文提出了单边移动盖板光栅和双边移动盖板光栅两种光栅结构,并使用严格耦合波分析(RCWA)方法对TM波垂直入射的一维微尺度光栅表面辐射特性进行了分析,研究了滑动盖板的厚度和位置对光栅表面结构辐射特性的影响。结果表明,相同盖板厚度,双边移动盖板光栅形成的发射率峰较单边移动盖板光栅形成的发射率峰具有较宽的半高全宽(FWHM),但峰值较低;随盖板向关闭侧移动,高发射率峰对应波长向长波方向移动;随盖板厚度增加,发射率峰向长波方向移动,其中双边移动盖板光栅结构形成的发射率峰变宽,峰值变小。     

Polarization properties of subwavelength metallic gratings in visible light band

Optical polarization properties of aluminum, gold and aluminum/gold subwavelength metallic gratings (SWMGs) are investigated numerically in the visible light band. Their performance as polarizing beam splitters are simulated with RCWA for varied metallic materials, grating depth and incident angle. Metallic waveguide theory is applied to explain the performance difference between Au and Al grating. A new type of Al/Au bimetallic is also investigated numerically for potential applications. PACS 42.79.Dj; 42.81.Gs; 73.20.Mf