Evolution with temperature of a single sol-gel TIO2 layer on sapphire (α-Al2O3) (0 0 0 1)

TiO₂ sol-gel layer has been deposited on single crystal sapphire (0 0 0 1) substrate. Evolution of the layer microstructure with the thermal treatment in the range 100-1100 °C has been studied using X-ray diffraction and X-ray reflectometry. TiO₂ layer density first increases with temperature up to 800 °C and then decreases with the appearance of a high roughness finally leading to anatase islands formation. The single crystal nature of the substrate seems to contribute to hinder the transformation of the anatase phase into the rutile phase and to induce a preferred orientation of the TiO₂ islands.     

Influence of Ca additives on the optical and dielectric studies of sol-gel derived PbTiO3 ceramics

Sintered ceramic powders of calcium-doped lead titanate [Pb_1−xCa_xTiO₃] ceramics with different Ca dopant concentration in the range (x=0-0.35) have been prepared using a sol-gel chemical route. The sol-gel technique is known to offer better purity and homogeneity, and can yield stoichiometric powders with improved properties at relatively lower processing temperature in comparison to conventional solid-state reaction. X-ray diffraction (XRD) and Raman spectroscopy studies have been carried out to identify the crystallographic structure and phase formation. The infrared absorption spectra in the mid-IR region (400-4000 cm⁻¹) show the band corresponding to the Ti-O bond at ∼576 cm⁻¹ and is found to shift to a higher wave number 592 cm⁻¹ with increasing Ca content. The dielectric properties as a function of frequency, and phase transition studies on sintered ceramic Pb_0.65Ca_0.35TiO₃ has been investigated in detail over a wide temperature range 30-600 °C and the results are discussed.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Comparative study of K0.5Bi0.5TiO3 nanoparticles derived from sol-gel-hydrothermal and sol-gel routes

A kind of novel lead-free ferroelectrics, potassium bismuth titanate, K_0.5Bi_0.5TiO₃ (KBT), has been prepared by sol-gel-hydrothermal and sol-gel routes, respectively, and the structural characters of as-synthesized powders were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The results indicated that sol-gel-hydrothermal route led to the formation of KBT nanowhiskers with diameters of 20 nm and lengths of 1 μm, and the processing temperature was as low as 160 °C, but the normal sol-gel route tended to form KBT cubic particles of about 100-200 nm, and the processing temperature was higher than 700 °C. It is believed that the gel precursor and hydrothermal environment play an important role in the formation of the nanowhiskers at low temperature. Due to the good sinterability of nanowhiskers, the ferroelectric and dielectric properties of KBT ceramics prepared by sol-gel-hydrothermal route were super to that prepared by sol-gel route.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

EPR study of nitrogen-doped mesoporous TiO2 powders

Mesoporous titanium dioxide powders were synthesized by the sol-gel route either directly or using the P123 templating agent and nitrogen doping from thiourea. X-ray diffraction studies show that doping and structuring give rise to rutile growth at a relatively low temperature of 400 °C compared to the transition point of pure TiO₂, which is close to 900 °C. Systematic EPR experiments were performed in order to monitor the involved paramagnetic centres with respect to calcination treatments and also to probe the nitrogen doping efficiency in the host media. Several paramagnetic species were found in these mesostructured samples mainly with oxygen radicals for calcinations at 400 °C, while nitrogen centres appear for calcination temperature as high as 500 °C. The effect of material microstructure on the effective incorporation of nitrogen in the TiO₂ lattice is also examined and compared in representative samples.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Structural, optical, and electrical properties of p-type NiO films and composite TiO2/NiO electrodes for solid-state dye-sensitized solar cells

p-Type nickel oxide thin films were prepared by sol-gel method, and their structural, optical and electrical properties were investigated. The Ni(OH)₂ sol was formed from nickel (II) acetate tetrahydrate, Ni(CH₃COO)₂·4H₂O, in a mixture of alcohol solution and poly(ethylene glycol), and deposited on an ITO substrate by spin coating followed by different heat treatments in air (50-800 °C). The formation and composition of NiO thin film was justified by EDX analysis. It is found that the thickness of the NiO film calcined at 450 °C for 1 h is about 120 nm with average particle size of 22 nm, and high UV transparency (∼75%) in the visible region is also observed. However, the transmittance is negligible for thin films calcined at 800 °C and below 200 °C due to larger particle size and the amorphous characteristics, respectively. Moreover, the composite electrode comprising n-type TiO₂ and p-type NiO is fabricated. The current-voltage (I-V) characteristics of the composite TiO₂/NiO electrode demonstrate significant p-type behavior by the shape of the rectifying curve in dark. The effect of calcination temperature on the rectification behavior is also discussed.     

Novel luminescent RE/TiO2 (RE = Eu, Gd) catalysts prepared by in-situation sol-gel approach construction of multi-functional precursors and their photo or photocatalytic oxidation properties

In this context, a novel synthesis method was used to fabricate rare earth/TiO₂ catalyst for the first time. Lanthanide (Eu, Gd) coordination polymers with picolinic acids were applied as precursors of titania oxide components, in particular, polyethylene glycol and polyacrylamide were added to assemble inorganic-organic hybrid polymeric network through an in-situation sol-gel technique. After sintering treatment of the multi-component precursor under 600 °C for 3 h, fluorescence excitation and emission spectra show that Eu/TiO₂ crystalline phosphor exhibits strong red luminescence under excitation wavelength at 394 and 464 nm. SEM and BET indicate the two hybrids are porous and homogenous. The oxidation experiments from trivalent arsenite As(III) to pentavalent arsenate As(V) by the above two catalysts substantiate that their surfaces have higher affinity to arsenate and can enhance photocatalytic oxidation activity in comparison with pure titania.     

Effects of depositing temperatures on structure and optical properties of TiO2 film deposited by ion beam assisted electron beam evaporation

TiO₂, which is high in refractive index and dielectric constant, plays an important role in the fields of optics and electronics. In this work, TiO₂ films were prepared on glass substrates by the technique of ion beam assisted electron beam evaporation. The films were deposited at 50, 150 and 300 °C, respectively. Then the as-deposited TiO₂ films were annealed at 450 °C for 1 h in vacuum atmosphere. Structures and optical properties of TiO₂ films were characterized by XRD, SEM, ellipsometry and spectrophotometer. As a result, the structure and the refractive index of films were improved by both the annealing and the increasing of the deposition temperature. The UV-vis transmittance spectra also confirmed that the deposition temperature has a significant effect on the transparency of the thin films. The highest transparency over the visible wavelength region of spectra was obtained at the deposition temperature of 300 °C. The allowed direct band gap at the deposition temperature ranging from 50 to 300 °C was estimated to be in the range from 3.81 to 3.92 eV.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Effect of oxidation temperature on microstructure, mechanical behaviors and surface morphology of nanocomposite Ti-Cx-Ny thin films

Two nanocomposite Ti-C_x-N_y thin films, TiC_0.95N_0.60 and TiC_2.35N_0.68, as well as one pure TiN, were deposited at 500 °C on Si(1 0 0) substrate by reactive unbalanced dc-magnetron sputtering. Oxidation experiments of these films were carried out in air at fixed temperatures in a regime of 250-600 °C with an interval of 50 °C. As-deposited and oxidized films were characterized and analyzed using X-ray diffraction (XRD), microindentation, Newton's ring methods and atomic force microscopy (AFM). It was found that the starting oxidation temperature of nanocomposite Ti-C_x-N_y thin films was 300 °C irrespective of the carbon content; however their oxidation rate strongly depended on their carbon content. Higher carbon content caused more serious oxidation. After oxidation, the film hardness value remained up to the starting oxidation temperature, followed by fast decrease with increasing heating temperature. The residual compressive stress did not show a similar trend with the hardness. Its value was first increased with increase of heating temperature, and got its maximum at the starting oxidation temperature. A decrease in residual stress was followed when heating temperature was further increased. The film surface roughness value was slightly increased with heating temperature till the starting oxidation temperature, a great decrease in surface roughness was followed with further increase of heating temperature.     

Structure and dielectric studies of nano-composite Fe2O3: BaTiO3 prepared by sol-gel method

Nano-structure pure barium titanate (BaTiO₃) and that was doped with iron oxide (Fe₂O₃), have been prepared by sol-gel method, using barium acetate (Ba(Ac)₂) and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The as-grown prepared samples by sol-gel technique were found to be amorphous, which crystallized to the tetragonal phase after synthesized at 750 °C in air for 1 h as detected from the XRD patterns. The XRD data were confirmed by transmission electron microscope (TEM). The dielectric properties namely; dielectric constant (ε′) and loss tangent (tan δ) in the frequency range between 42 Hz and 1 MHz, at range of temperature 25-250 °C were investigated. The temperature dependence of ε′ and tan δ for the undoped and doped materials, at 1 kHz, was also investigated. As a result, tan δ increased rapidly with decreasing temperature below 125 °C (Curie temperature) while above this temperature, tan δ shows temperature independent. As a result, below and above Curie temperature, ferroelectric phase and paraelectric phase of BaTiO₃ can be obtained, respectively.     

Influence of porous morphology on optical dispersion properties of template free mesoporous titanium dioxide (TiO2) films

This paper focuses the influence of porous morphology on the microstructure and optical properties of TiO₂ films prepared by different sol concentration and calcination temperatures. Mesoporous TiO₂ thin films were prepared on the glass substrates by sol-gel dip coating technique using titanium (IV) isopropoxide. Porous morphology of the films can be regulated by chemical kinetics and is studied by scanning electron microscopy. The optical dispersion parameters such as refractive index (n), oscillator energy (E_d), and particle co-ordination number (N_c) of the mesoporous TiO₂ films were studied using Swanepoel and Wemple-DiDomenico single oscillator models. The higher precursor concentration (0.06 M), films exhibit high porosity and refractive index, which are modified under calcination treatment. Calcinated films of low metal precursor concentration (0.03 M) possess higher particle co-ordination number (N_c = 5.05) than that of 0.06 M films (N_c = 4.90) due to calcination at 400 °C. The lattice dielectric constant (E_∞) of mesoporous TiO₂ films was determined by using Spintzer model. Urbach energy of the mesoporous films has been estimated for both concentration and the analysis revealed the strong dependence of Urbach energy on porous morphology. The influence of porous morphology on the optical dispersion properties also has been explained briefly in this paper.     

Annealing temperature effect on the properties of mercury-doped TiO2 films prepared by sol-gel dip-coating technique

This work presents the annealing temperature effect on the properties of mercury (Hg)-doped titanium dioxide (TiO₂). Thin films and polycrystalline powders have been prepared by sol-gel process. The structure, surface morphology and optical properties, as a function of the annealing temperature, have been studied by atomic force microscopy (AFM), Raman, reflectance and ellipsometric spectroscopies. In order to determine the transformation points, we have analyzed the xerogel-obtained powder by differential scanning calorimetry (DSC). Raman spectroscopy shows the crystalline anatase and rutile phases for the films annealed at 400 °C and 1000 °C respectively. The AFM surface morphology results indicate that the particle size increases from 14 to 57 nm by increasing the annealing temperature. The complex index and the optical band gap (E_g) of the films were determined by the spectroscopic ellipsometry analysis. We have found that the optical band gap decreases by increasing the annealing temperature.     

Nanostructure of photocatalytic TiO2 films sputtered at temperatures below 200 °C

The article reports on correlations between the process parameters of reactive pulsed dc magnetron sputtering, physical properties and the photocatalytic activity (PCA) of TiO₂ films sputtered at substrate surface temperature T_surf ≤ 180 °C. Films were deposited using a dual magnetron system equipped with Ti (Ø50 mm) targets in Ar + O₂ atmosphere in oxide mode of sputtering. The TiO₂ films with highly photoactive anatase phase were prepared without a post-deposition thermal annealing. The decomposition rate of the acid orange 7 (AO7) solution during the photoactivation of the TiO₂ film with UV light was used for characterization of the film PCA. It was found that (i) the partial pressure of oxygen pO₂ and the total sputtering gas pressure p_T are the key deposition parameters influencing the TiO₂ film phase composition that directly affects its PCA, (ii) the structure of sputtered TiO₂ films varies along the growth direction from the film/substrate interface to the film surface, (iii) ∼500 nm thick anatase TiO₂ films with high PCA were prepared and (iv) the structure of sputtered TiO₂ films is not affected by the substrate surface temperature T_surf when T_surf < 180 °C. The interruption of the sputtering process and deposition in long (tens of minutes) pulses alternating with cooling pauses has no effect on the structure and the PCA of TiO₂ films and results in a decrease of maximum value of T_surf necessary for the creation of nanocrystalline nc-TiO₂ film. It was demonstrated that crystalline TiO₂ films with high PCA can be sputtered at T_surf ≤ 130 °C. Based on obtained results a phase zone model of TiO₂ films was developed.     

Synthesis and magnetic study on Mg-substituted Li-Mn spinel oxides

LiMn_2−xMg_xO₄ (X<0.5) cubic spinel oxide was synthesized by the sol-gel technique using Li-nitrate, Mn-acetate and Mg-acetate salts. The gel precursors were decomposed at 300 °C in air and then annealed at temperatures ranging from 500 to 850 °C in an oxygen flow. For a fixed annealing temperature of 700 °C, the lattice constant decreased with an increase in the substitution degree X and a discontinuity was found around X=0.3. With a further increase in X>0.3, the space group of the crystal structure was converted from Fd3m to P4₃32 by the cation ordering in the octahedral site. The low-temperature magnetization increased with X, and the Weiss constant moved in the positive direction and changed its sign from negative to positive around X=0.3. In the case of X=0.5, all the specimens showed P4₃32 structure and ferromagnetic character. The maximum Curie temperature (T_c=23 K) and the maximum magnetization (M_s=4.68 μ_B per the chemical formula unit) were attained simultaneously for the specimen obtained around 700 °C. The Mn valence state was sensitive not only to the substitution but also to the preparation conditions. Hence, it was possible to explain these variations by considering the magnetic interactions between transition metal ions.     

Thermal behavior and catalytic activity in naphthalene destruction of Ce-, Zr- and Mn-containing oxide layers on titanium

The present paper is devoted to studies of the composition and surface structure, including those after annealing at high temperatures, and catalytic activity in the reaction of naphthalene destruction of Ce-, Zr- and Mn-containing oxide layers on titanium obtained by means of the plasma electrolytic oxidation (PEO) method. The composition and structure of the obtained systems were investigated using the methods of X-ray phase and energy dispersive analysis and scanning electron microscopy (SEM). It was demonstrated that Ce- and Zr- containing structures had relatively high thermal stability: their element and phase compositions and surface structure underwent virtually no changes after annealing in the temperature range 600-800 °C. Annealing of Ce- and Zr-containing coatings in the temperature range 850-900 °C resulted in substantial changes of their surface composition and structure: a relatively homogeneous and porous surface becomes coated by large pole-like crystals. The catalytic studies showed rather high activity of Ce- and Zr-containing coatings in the reaction of naphthalene destruction at temperatures up to 850 °C. Mn-containing structures of the type MnO_x + SiO₂ + TiO₂/Ti have a well-developed surface coated by “nano-whiskers”. The phase composition and surface structure of manganese-containing layers changes dramatically in the course of thermal treatment. After annealing above 600 °C nano-whiskers vanish with formation of molten structures on the surface. The Mn-containing oxide systems demonstrated lower conversion degrees than the Ce- and Zr-containing coatings, which can be attributed to substantial surface modification and formation of molten manganese silicates at high temperatures.     

High-temperature oxidation resistance and magnetic properties of Si-doped Sm2Co17-type magnets at 500 °C

The high-temperature oxidation resistance and magnetic properties of Si-doped Sm₂Co₁₇-type magnets at 500 °C were systematically investigated. The Sm(Co_0.76, Fe_0.1, Cu_0.1, Zr_0.04)₇Si_x (x=0–0.6) magnets were prepared by the conventional powder metallurgical technique. It is found that the addition of silicon in the Sm₂Co₁₇-type magnet can remarkably improve its oxidation resistance. Moreover, a small amount of silicon addition can also increase its high-temperature intrinsic coercivity. A maximum intrinsic coercivity of 6.7 kOe at 500 °C was obtained for the Sm₂Co₁₇-type magnet with Si content x=0.4, whose high-temperature maximum energy product loss was about 2.5 times smaller than pure Sm₂Co₁₇-type magnet after oxidation at 500 °C for 100 h, indicating the enhanced oxidation resistance. Its corresponding Curie temperature and saturation magnetization are about 723.9 °C and 7.4 kG, respectively.     

Fabrication of TiO2 μ-donuts by sol-gel spin coating using a polymer mask

TiO₂ μ-donuts have been fabricated on glass and silicon substrates using polymer masks in combination with a sol-gel technique. Cylindrical poly(methyl methacrylate) (PMMA) nanopillars have been created using a composite polymer of polystyrene (PS) and PMMA followed by careful removal of the PS. Atomic force microscopy (AFM) analyses show that the height and diameter of the PMMA cylinders used as the mask are 440 ± 5 nm and 2.1 ± 0.2 μm, respectively. The cylindrical PMMA nanopillars have been coated with the sol of the TiO₂ precursor by a spin coating technique and annealed in air at elevated temperature to remove the PMMA mask. Removal of the PMMA mask has resulted in the formation of well ordered μ-donuts of TiO₂ on silicon surfaces. The interior and exterior heights of the TiO₂ μ-donuts are found to be 373 ± 152 nm and 457 ± 136 nm, respectively; and the interior and exterior diameters of the TiO₂ μ-donuts are found to be 1.33 ± 0.63 μm and 2.82 ± 0.50 μm, respectively. X-ray photoelectron spectroscopy (XPS) spectra of the TiO₂ μ-donuts as well as the smooth TiO₂ thin film showed signals from Ti and O confirming the presence of TiO₂ with Ti 2p_3/2 and O 1s peaks at 458.8 eV and 530.4 eV, respectively. The O 1s peak of the TiO₂ μ-donuts shows another peak at binding energy 532.0 eV due to SiO₂, as during annealing, the PMMA evaporates and the Si substrate is exposed. The X-ray diffractometer (XRD) pattern of the smooth TiO₂ thin film indicates that the anatase phase is present, with the characteristic peaks observed at 2θ values of 25.4°, 37.4°, and 48° corresponding to (1 0 1), (0 0 4), and (2 0 0) planes, respectively. UV-vis absorption spectra of TiO₂ μ-donuts on glass showed an unusual absorption of light in the visible region at ∼524 nm in addition to the usual UV absorption at ∼337 nm.