Effect of nickel doping on structural, optical and electrical properties of TiO2 nanoparticles by sol-gel method

Nickel-doped anatase TiO₂ nanoparticles have been prepared by sol-gel method. The X-ray powder diffraction study reveals that all the prepared samples have pure anatase phase tetragonal system. The average crystallite size of the prepared sample is 14 nm, when found through transmission electron microscope. A strong frequency dependence of both dielectric constant (?′) and dielectric loss (tan δ) were observed for various dopant levels at room temperature in the frequency range of 42 Hz to 5 MHz. At low frequency, the piling up of mobile charge carriers at the grain boundary produces interfacial polarization giving rise to high dielectric constant. The asymmetric shape of frequency dependence of the dielectric loss for the primary relaxation process is observed for each concentration. From the ac conductivity studies, the reduction in conductivity may arise due to the decreasing particle with the increase in Ni-dopant level.     

Dielectric dispersion in PbO-Sb2O3-As2O3:V2O5 glasses

Dielectric properties, viz. dielectric constant ε′, loss tan δ and a.c conductivity σ_ac (over a wide range of frequency and temperature) and dielectric breakdown strength of PbO-Sb₂O₃-As₂O₃ glasses doped with V₂O₅ (ranging from 0 to 0.5 mol%) are studied. Analysis of these results, based on optical absorption and ESR spectra, indicates that the insulating strength of the glasses is comparatively high when the concentration of V₂O₅ is about 0.3 mol% in the glass matrix.     

Impedance spectroscopy study and ground state electronic properties of In(Mg1/2Ti1/2)O3

The complex perovskite oxide In(Mg_1/2Ti_1/2)O₃ (IMT) is synthesized by a solid state reaction technique. The X-ray diffraction of the sample at 30 °C shows a monoclinic phase. The dielectric properties of the sample are investigated in the temperature range from 143 to 373 K and in the frequency range from 580 Hz to 1 MHz using impedance spectroscopy. An analysis of the dielectric constant ε′ and loss tangent (tan δ) with frequency is performed assuming a distribution of relaxation times. The Cole-Cole model is used to explain the relaxation mechanism in IMT. The scaling behavior of imaginary part of electric modulus (M″) shows that the relaxation describes the same mechanism at various temperatures. The electronic structure and hence the ground state properties of IMT is studied by X-ray photoemission spectroscopy (XPS). The valence band XPS spectrum is compared with the electronic structure calculation. The electronic structure calculation indicates that the In-5s orbital introduces a significant density of states at the Fermi level, which is responsible for a high value of conductivity in IMT.     

Dielectric relaxation and ac conductivity of double perovskite oxide Ho2ZnZrO6

Double perovskite oxide holmium zinc zirconate Ho₂ZnZrO₆ (HZZ) is synthesized by solid state reaction technique under a calcination temperature of 1100 °C. The crystal structure has been determined by powder X-ray diffraction, which shows monoclinic phase at room temperature. The variation of dielectric constant (ε′) and loss tangent (tan δ) with frequency is carried out assuming a distribution of relaxation times. The frequency corresponding to loss tangent peak is found to obey an Arrhenius law with activation energy of 89.7 meV. The frequency-dependant electrical data are analyzed in the framework of conductivity and electric modulus formalisms. Both these formalisms show qualitative similarities in relaxation times. The scaling behaviour of imaginary electric modulus shows the temperature-independent nature of the distribution of relaxation times. Nyquist plots are drawn to identify an equivalent circuit and to know the bulk and interface contributions.     

AC conductivity and dielectric relaxation in Ba(Sm1/2Nb1/2)O3 ceramic

The complex perovskite oxide a barium samarium niobate (BSN) synthesized by solid-state reaction technique has single phase with cubic structure. The scanning electron micrograph of the sample shows the average grain size of BSN∼1.22 μm. The field dependence of dielectric response and loss tangent were measured in the temperature range from 323 to 463 K and in the frequency range from 50 Hz to 1 MHz. The complex plane impedance plots show the grain boundary contribution for higher value of dielectric constant in the low frequency region. An analysis of the dielectric constant (ε′) and loss tangent (tan δ) with frequency was performed assuming a distribution of relaxation times as confirmed by the scaling behaviour of electric modulus spectra. The low frequency dielectric dispersion corresponds to DC conductivity. The logarithmic angular frequency dependence of the loss peak is found to obey the Arrhenius law with an activation energy of 0.71 eV. The frequency dependence of electrical data is also analyzed in the framework of conductivity and electric modulus formalisms. Both these formalisms show qualitative similarities in relaxation times. The scaling behaviour of imaginary part of electric modulus M″ and dielectric loss spectra suggest that the relaxation describes the same mechanism at various temperatures in BSN. All the observations indicate the polydispersive relaxation in BSN.     

Dielectric properties of barium titanate ceramics modified by SiO2 and by BaO-SiO2

The influence of SiO₂ on the dielectric properties of barium titanate ceramics was investigated. SiO₂ had been doped solely and together with BaO into barium titanate before calcination. X-ray diffraction showed that all the ceramics were of a pure perovskite phase after sintering at 1275 °C for 2 h. For SiO₂-doping, there was about 2.5 °C increase in Curie temperature per molar percentage of doping and the leakage current was obviously increased, especially at low voltages for relatively high doping levels. While for the co-doping of SiO₂ and BaO, there was little change in Curie temperature. The point defects formed through the dopings were proposed responsible for the effects. It was suggested that SiO₂ is important to barium titanate ceramics not only for sintering but also for modifying their properties.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Influence of frequency, temperature and composition on electrical properties of polycrystalline Co0.5CdxFe2.5−xO4 ferrites

Polycrystalline ferrites with general formula Co_0.5Cd_xFe_2.5−xO₄ (0.0?x?0.5) were prepared by sol-gel method. The dielectric properties ε′, ε″, loss tangent tan δ and ac conductivity σ_ac have been studied as a function of frequency, temperature and composition. The experimental results indicate that ε′, ε″, tan δ and σ_ac decrease as the frequency increases; whereas they increase as the temperature increases. These parameters are found to increase by increasing the concentration of Cd content up to x=0.2, after which they start to decrease with further increase in concentration of Cd ion. The dielectric properties and ac conductivity in studied samples have been explained on the basis of space charge polarization according to Maxwell and Wagner's two-layer model and the hoping between adjacent Fe²⁺ and Fe³⁺ as well as the hole hopping between Co³⁺and Co²⁺ ions at B-sites. The values of activation energies E_f for conduction process are determined from Arrhenius plots, and the variations in these activation energies as a function of Cd content are discussed. The complex impedance analysis is used to separate the grain and grain boundary of the system Co_0.5Cd_xFe_2.5−xO₄. The variations of both grain boundary and grain resistances with temperature and composition are evaluated in the frequency range 42 Hz-5 MHz.     

Electrical properties of high Curie temperature (1−x)Pb(In1/2Nb1/2)O3-xPbTiO3 single crystals grown by the solution Bridgman technique

0.65Pb(In_1/2Nb_1/2)O₃-0.35PbTiO₃ (PINT65/35) (starting composition) single crystals were grown successfully through the solution Bridgman technique using PbO flux and PMNT67/33 seed crystals. Because of the composition variation, the final composition of achievable crystals is in a range of 0.32-0.34 with the corresponding T_c range of 265-269 °C. The (001) plates of as-grown PINT66/34 single crystals show high Curie temperature (T_c=269 °C) and rhombohedral-tetragonal phase transition temperature (T_rt=134 °C). Besides, good electrical properties with high dielectric constant (ε>3000), low dielectric loss (tan δ∼1.2%), high piezoelectric constant (d₃₃∼2000 pC/N) and large electromechanical coupling factor (k_t≈59%) at room temperature have been obtained on the (001) plates. The sound velocity, acoustic impedance and other piezoelectric parameters were also measured on the (001) plates in this study, which provide us more detailed information about PINT66/34 single crystals.     

Synthesis, microstructure, dielectric and magnetic properties of Cu substituted Ni-Li ferrites

Cu substituted Ni-Li spinel ferrites were prepared by a conventional sol-gel auto-combustion method. The structure, surface morphology, dielectric and magnetic properties were investigated by X-ray diffraction, infrared spectroscopy, scanning electron microscopy, impedance spectroscopy and vibrating sample magnetometer, respectively. X-ray diffraction studies reveal the single phase spinel structure of the ferrites and the crystallite size varies from 23 to 35 nm. Incorporation of Cu in the Ni-Li ferrites increases the grain size. The dielectric parameters such as ε´, ε′′, loss tan δ and ac conductivity (σ_ac) have been measured for the annealed samples in the temperature range from 35 to 200 °C and over the frequency range from 10¹ to 10⁷ Hz. The saturation magnetization and coercivity show a dependence on the composition and microstructure. The values of saturation magnetization vary from 25.6 to 33.6 emu/g with increase in x for samples annealed at 600 °C. The values of the coercivity increase from 170 to 203 Oe with increase in x.     

Effect of magnesium substitution on dielectric and magnetic properties of Ni-Zn ferrite

The dielectric and magnetic properties of Mg incorporated Ni-Zn spinel ferrites have been investigated. Ni_0.5−xZn_0.5Mg_xFe₂O₄ ferrites have been prepared by sol-gel auto-combustion technique. The as prepared ferrites were annealed at 673, 873 and 1073 K. The X-ray diffraction studies reveal the spinel structure of annealed ferrites. The TEM results are in agreement with XRD results. FTIR study has also been carried out to get insight into the structure of these ferrites. The dielectric measurements show that the dielectric constant (ε′), dielectric loss (tan δ) and conductivity (σ_ac) increase on incorporation of Mg in the Ni-Zn ferrite. ε′, tan δ and σ_ac also show dependence on temperature, frequency of external applied electric field and microstructure of the samples. The magnetic moment measurements reveal that the saturation magnetization (M_s) increases and coercivity (H_c) decreases with the increase in concentration of Mg²⁺ ions. M_s and H_c also show dependence on the annealing temperature.     

Effect of sintering temperature on structure and nonlinear dielectric properties of Ba0.6Sr0.4TiO3 ceramics prepared by the citrate method

Ba_0.6Sr_0.4TiO₃ ceramics were prepared by a citrate precursor method. The structure and nonlinear dielectric properties of the resulting ceramics were investigated within the sintering temperature range 1200-1300 °C. Adopting fine Ba_0.6Sr_0.4TiO₃ powder derived from the citrate method was confirmed to be effective in reducing the sintering temperatures required for densification. The ceramic specimens sintered at 1230-1280 °C presented relative densities of around 95%. A significant influence of sintering temperature on the microstructure and nonlinear dielectric properties was detected. The discrepancy in nonlinear dielectric behavior among the specimens sintered at different temperatures was qualitatively interpreted in terms of the dielectric response of polar micro-regions under bias electric field. The specimens sintered at 1230 and 1250 °C attained superior nonlinear dielectric properties, showing relatively low dielectric losses (tan δ) of 0.24% and 0.22% at 10 kHz together with comparatively large figure of merits (FOM) of 121 and 142 at 10 kHz and 20 kV/cm, respectively.     

Relaxor behavior in the (1−x)BaSnO3 - xPbTiO3 solid solution

The relaxor behavior was revealed in the solid solution (1−x)BaSnO₃-xPbTiO₃[(1−x)BSn-xPT] with compositions near x=0.50. The real permittivity (ε^′) and loss tangent (tanδ) exhibit diffuse and dispersive maxima, whose temperature shifts towards a higher temperature upon the increasing frequency. The frequency dependence of the temperature of the dielectric maximum (T_m) follows the Vogel-Fulcher law, as in the canonical relaxor. A deviation from the Curie-Weiss law was observed below the Burns temperature (T_B) and well above the Curie temperature (T_C). These phenomena are well consistent with typical relaxors, which explains the existence of the relaxor behavior in the (1−x)BSn-xPT solid solution.     

Magnetic and electrical properties of bulk BaTiO3+MgFe2O4 composite

BaTiO₃+MgFe₂O₄ material system was synthesized by hybrid chemical process using chlorides and nitrates of barium, titanium, iron, and magnesium. Magnetic properties of the composite samples measured as a function of annealing conditions indicated soft magnetic behavior. Saturation specific magnetization from 8 21 emu/g was observed for samples annealed at temperature between 950 and 1150 °C. Variation of specific saturation magnetization with respect to annealing temperature was related with the distribution of Fe cations in the tetrahedral and octahedral sites of MgFe₂O₄. Electrical properties of the samples annealed at different temperatures were measured to analyze the coexistence of ferroelectric phase. Dielectric constant varying from 15 to 200 with respect to frequency was observed for samples annealed from 950 to 1150 °C.     

Orientation-dependent dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films prepared by sol-gel method

The orientation-dependent dielectric properties of barium stannate titanate (Ba(Sn_0.15Ti_0.85)O₃, BTS) thin films grown on (1 0 0) LaAlO₃ single-crystal substrates through sol-gel process were investigated. The nonlinear dielectric properties of the BTS films were measured using an inter-digital capacitor (IDC). The results show that the in-plane dielectric properties of BTS films exhibited a strong sensitivity to orientation. The upward shift of Curie temperature (T_c) of the highly (1 0 0)-oriented BTS thin films is believed to be attributing to a tensile stress along the in-plane direction inside the film. A high tunability of 47.03% was obtained for the highly (1 0 0)-oriented BTS films, which is about three times larger than that of the BTS films with random orientation, measured at a frequency of 1 MHz and an applied electric field of 80 kV/cm. This work clearly reveals the highly promising potential of BTS films for application in tunable microwave devices.     

Sintering temperature dependence of room temperature magnetic and dielectric properties of Co0.5Zn0.5Fe2O4 prepared using mechanically alloyed nanoparticles

Co_0.5Zn_0.5Fe₂O₄ nanoparticles were prepared using mechanical alloying (MA) and sintering. The crystallite size, coercivity, retentivity and saturation magnetization were also measured. The frequency dependence of dielectric and the magnetic parameters, namely, real permittivity ε′, loss tanget tan δ, real permeability μ′ and loss factor μ″ were measured at room temperature for samples sintered from 600 to 1000 °C, in the frequency range 10 MHz to 1.0 GHz. The results show that the crystallite size of the resulting products ranges between 16 and 67 nm for as-milled sample and the sample sintered at 1000 °C, respectively. The sample sintered at 1000 °C, measured at room temperature exhibited a saturation magnetization of 37 emu g⁻¹. The values of permittivity remain constant within the measured frequency, but vary with sintering temperature. The permeability values, on the other hand however vary with both the sintering temperature and the frequency, thus, the absolute value of the permeability decreased after the natural resonance frequency.     

Study of the structural, dielectric and magnetic properties of Bi2O3 and PbO addition on BiFeO3 ceramic matrix

In this paper we studied the effects of Bi₂O₃ and PbO addition on BiFeO₃ (BFO) ceramic matrix. The structural, dielectric and magnetic properties of fifteen BFO samples were discussed in view of possible applications in RF and microwave devices. The present work also reports the preparation of the samples. Polyvinyl alcohol (PVA) and tetraethyl orthosilicate (TEOS) were also added as a binder in the fabrication procedure. The samples have been studied by X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and magnetic hysteresis measurements. Further, a study based on impedance spectroscopy also has been done. Dielectric permittivity (ε′) and dielectric loss (tan δ) were measured at room temperature in the frequency range 100 Hz-10 MHz, as well as a.c. conductivity. The -Im[Z(f)] versus Re[Z(f)] plot has been obtained. The samples were investigated in view of possible applications like miniaturized filters, diplexers and dielectric resonator antennas (DRA). In the RF and MW frequency region, the application of magneto-dielectric and multiferroic perovskite composite materials is desirable for the miniaturization of components.     

Investigation on dielectric relaxation of PMMA-grafted natural rubber incorporated with LiCF3SO3

Natural rubber (NR) grafted with 30 wt% poly (methyl methacrylate) (PMMA) and designated as MG30 has been added with varying amounts of LiCF₃SO₃. X-ray diffraction (XRD) shows the samples to be amorphous. Fourier transform infrared (FTIR) spectroscopy indicates complexation between the cation of the salt and the oxygen atom of the CO and –COO- groups of MG30. From electrochemical impedance spectroscopy (EIS), MG30 with 30 wt% LiCF₃SO₃ salt exhibits the highest ambient conductivity of 1.69×10⁻⁶ S cm⁻¹ and lowest activation energy of 0.24 eV. The dielectric behavior has been analyzed using dielectric permittivity (ε′), dissipation factor (tan δ) and dielectric modulus (M^?) of the samples. The dielectric constant of pure MG30 has been estimated to be ∼1.86.     

BiFeO3 ceramic matrix with Bi2O3 or PbO added: Mössbauer, Raman and dielectric spectroscopy studies

In this paper Mössbauer, Raman and dielectric spectroscopy studies of BiFeO₃ (BFO) ceramic matrix with 3 or 10 wt% of Bi₂O₃ or PbO added, obtained through a new procedure based on the solid-state method, are presented. Mössbauer spectroscopy shows the presence of a single magnetically ordered phase with a hyperfine magnetic field of 50 T. Raman spectra of BFO over the frequency range of 100-900 cm⁻¹ have been investigated, at room temperature, under the excitation of 632.8 nm wavelength in order to evaluate the effect of additives on the structure of the ceramic matrix. Detailed studies of the dielectric properties of BiFeO₃ ceramic matrix like capacitance (C), dielectric permittivity (ε) and dielectric loss (tan δ), were investigated in a wide frequency range (1 Hz-1 MHz), and in a temperature range (303-373 K). The complex impedance spectroscopy (CIS) technique, showed that these properties are strongly dependent on frequency, temperature and on the added level of impurity. The temperature coefficient of capacitance (TCC) of the samples was also evaluated. The study of the imaginary impedance (−Z″) and imaginary electric modulus (M″) as functions of frequency and temperature leads to the measurement of the activation energy (E_ac), which is directly linked to the relaxation process associated with the interfacial polarization effect in these samples.     

Influence of boron on the giant magnetocaloric effect of La(Fe0.9Si0.1)13

The influences of boron addition on the phase formation, Curie temperature and magnetic entropy change of the NaZn₁₃-type La(Fe_0.9Si_0.1)₁₃ compound have been investigated. Eight boron containing La(Fe_0.9Si_0.1)₁₃B_x samples were prepared with x=0, 0.03, 0.06, 0.1, 0.2, 0.3, 0.5 and 0.6, respectively. Experimental results show that a small amount of B addition in La(Fe_0.9Si_0.1)₁₃ forms the solid solution NaZn₁₃-type structure phase by substituting B for Si or doping B into interstitial position of the lattice, preserves its giant magnetocaloric effects due to their first-order structural/magnetic transition, as well as increase its Curie temperature T_c slightly. The maximum magnetic entropy changes in the magnetic field change of 0–1.6 T are around 20 J kg^–1 K^–1 for the samples with Boron addition less than 0.3, while improving the Curie temperatures by 2 K.