新型巯基化合物自组装膜修饰电极对铜离子的检测

合成了一种新型的巯基化合物,在金电极上形成自组装膜,以循环伏安法和电化学阻抗法(EIS)对自组装膜进行表征,基于其末端的氨基对铜离子的配位效应,实现了对铜离子的快速检测,并优化了沉积时间、pH、静止时间、沉积电压等检测条件.同时研究了铜离子与人血清白蛋白的相互作用.结果表明,该组装膜在2×10-7 ～2.5×10-3 mol/L范围内对铜离子有线性响应,检出限为0.05 μmol·L-1,其与蛋白的结合常数为2.20×103 L/mol.银离子、锌离子等对铜离子的测定几乎没有干扰.     

多相高分子快离子导体阻抗谱的研究

研究了以ＬｉＣｌＯ４掺杂的聚乙二醇聚氨酯双离子导体及磺酸型聚乙二醇聚氨酯离聚物单一离子导体的阻抗谱，给出了多相快离子导体交流阻抗测试系统的等效电路．通过阻抗谱计算机解析，计算得出了样品的基本电学参数．通过讨论界面阻抗的色散现象，计算出样品的离子电导率，和阻抗谱解析法得到的结果相一致．     

环氧/氟碳复合涂层失效过程的电化学阻抗谱研究

用电化学阻抗技术研究了环氧富锌底漆、环氧云铁中间漆和氟碳面漆构成的多层复合涂层在四种不同腐蚀环境中的失效过程.涂层在四种环境中的失效速率按下列顺序降低:3.5%NaCl浸泡+紫外照射,45℃湿热环境,35℃盐雾试验,3.5%NaCl浸泡.尽管涂层在四种不同环境中失效速率差别很大,但不同环境中阻抗中频区的相角,尤其是10Hz频率的相角,与涂层的低频阻抗值变化趋势非常接近.由于中频区的相角可以快速测量,因此可以作为在工程现场定性评价涂层保护性能的参数.     

环氧树脂涂覆LY12铝合金在NaCl溶液中的阻抗模型

分别研究了裸LY12铝合金及涂覆环氧树脂涂层后合金在3.5％NaCl溶液中的电化学阻抗谱（EIS）.结果表明,LY12铝合金在点蚀电位以下阻抗谱上出现两个容抗弧,高频段对应Cl－参与的成膜阻抗,低频段对应铝阳极溶解的电化学反应阻抗.合金发生点蚀后出现低频感抗弧.合金/电极在NaCl溶液中先发生涂层吸水,当水及O2抵达基体后建立起电化学反应界面,合金遭受腐蚀；受涂层阻挡的影响,腐蚀产物的扩散逐渐成为控制步骤；当扩散速度较慢的Cl－抵达涂层/金属界面后,与界面处聚集的腐蚀产物间发生化学反应,完成成膜过程,阻抗谱上出现盐膜的阻抗,而扩散阻抗消失.提出了不同浸泡失效阶段涂层电极体系的阻抗模型.     

模拟深海压力环境下有机涂料/基底金属腐蚀电化学行为研究Ⅰ.海水压力对水在涂层中传输行为和涂层防护性能的影响

于实验室模拟深海压力环境,应用电化学阻抗谱(EIS)研究了有机涂料/基底金属的腐蚀电化学行为.分析海水压力对水在涂层中传输行为和涂层防护性能的影响.结果表明,与常压海水相比,在高压海水(3.5MPa)条件下,该涂层具有不同的电化学阻抗特征,主要表现在高压海水加快了涂层的吸水过程,增大了涂层的吸水率,从而加速了涂层的腐蚀失效过程,致使防护性能变差.     

缓蚀剂在阳极电泳涂装中的应用

在电泳涂装工艺中使用缓蚀剂，可提高阳极电泳涂层的防腐蚀性，实验表明，沥青电泳漆与缓蚀剂的电泳共沉积涂层对基底金属具有较高的防护性能，探讨了共沉积涂层中缓蚀剂的缓蚀机理。     

丙烯酸十二酯用量对PA乳液防腐性能的影响

在现有核壳乳液聚合法基础上，改进聚合工艺制备具有不同丙烯酸十二酯(LMA)含量的水性丙烯酸乳液，讨论不同LMA含量对涂层性能的影响，并通过盐水浸泡实验、电化学阻抗研究量化涂膜的防腐性能。结果表明，核聚合阶段增加LMA用量有利于提高涂层的防腐性能。配方L16经过长期的3.5%(wt)盐水浸泡后，阻抗值仍有5.049 00×10⁶Ω·cm²,L16树脂乳液成膜涂层防腐性能最佳。     

Cu—ZSM—5分子筛表面铜离子的价态研究

以吸附ＣＯ红外光谱结合ＴＰＲ谱详细表征了经真空自还原及用不同还原剂还原的Ｃｕ－ＺＳＭ－５分子筛样品，考察了表面铜离子的价态分布情况及其影响因素，得知铜在Ｃｕ－ＺＳＭ－５是还原的。用不同方法进行氧化和还原时的难易程度不同。研究了用不同方法进行氧化还原时铜的价态转变条件和铜离子在不同价态间氧化还原循环的可逆性。     

基于纳米载体的缓蚀体系设计研究

通过软模板法制备粒径集中在100 nm的介孔二氧化硅作为纳米载体负载缓蚀剂分子苯并三氮唑(BTA),再通过单宁酸与三价铁离子在介孔氧化硅表面自组装形成金属多酚网络结构,由此构筑pH响应的智能控制释放体系。利用TEM,SEM,FTIR等表征手段证实了缓蚀剂分子的成功负载以及外层金属多酚网络结构的成功生长。利用电化学阻抗谱探究了制备的智能控释体系对金属的防护性能影响。结果表明,制备的pH响应智能控释体系能够很好地为铜电极提供防护,同时提升了复合环氧涂层的防护性能。     

Cu-ZSM-5分子筛中铜的精细结构和NO催化分解

用ＥＸＡＦＳ技术研究了不同交换度的还原、再氧化处理的Ｃｕ－ＺＳＭ－５分子筛中筛中铜离子的精细结构，在ＺＳＭ－５分子筛中，存在两种铜可占据的位置：一种具有饱和的氧配位的较短的铜氧距离，另一种铜氧配位不饱和且铜氧距离较远，离子交换时，铜离子可能优先占据前者，其量低于３０％。这两类铜的催化能力差别甚大，前者几乎无催人分解ＮＯ的活性。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.