咪唑基离子液体非共价修饰的石墨烯结构与分散性

在离子液体氯化-1-烯丙基-3-甲基咪唑（AmimCl）存在的条件下,利用水合肼对氧化石墨烯进行同步还原,制备了一种可稳定分散在N,N-二甲基甲酰胺（DMF）和乙酸丁酯等有机溶剂中的离子液体改性石墨烯（IL-G）。运用红外光谱（FTIR）、紫外-可见吸收光谱（UV-Vis）、热失重分析（TGA）、原子力显微镜（AFM）、拉曼光谱（Raman）、X射线电子衍射（XRD）和X射线光电子能谱（XPS）对制备的改性石墨烯进行结构性能测试,结果表明离子液体AmimCl与石墨烯之间存在π-π和阳离子-π的相互作用,能较好的吸附在石墨烯表面。TGA测试表明IL-G中离子液体的比例约为7.20wt%。同时,AFM结果显示改性石墨烯剥离在DMF中的平均厚度是0.962nm。由于非共价改性石墨烯可再分散于DMF和乙酸丁酯中,通过紫外可见吸收光谱测得其最大分散浓度分别是1.69mg·mL^-1和1.12mg·mL^-1。     

离子液体化石墨烯量子点及其对H2PO4-的荧光增强识别

通过表面修饰法制备了离子液体化石墨烯量子点(GQDs-IL),采用透射电子显微镜(TEM)、原子力显微镜(AFM)、傅里叶变换红外光谱仪(FTIR)、X射线光电子能谱仪(XPS)等对其形貌和结构进行了表征.结果 表明离子液体与GQDs通过酰胺键相连,GQDs-IL的粒径分布均匀,平均粒径为4.6nm.光谱性能表明,GQDs-IL在二甲基甲酰胺(DMF)溶液中,在常见阴离子(F-,Cl-,Br-,I-,AcO-,HSO4-,H2PO4-,CN-)中能够专一性地识别H2PO4-,滴加H2PO4-后引起荧光增强3.61倍,检出限为3.2 nmol/L,其它阴离子的存在并未干扰GQDs-IL对H2PO4-的检测.     

荧光石墨烯量子点制备及其在细胞成像中的应用

利用电化学方法在碱性条件下电解石墨棒, 通过常温下水合肼还原, 得到5～10 nm的荧光石墨烯量子点(Graphene Quantum Dots, GQDs). 通过透射电子显微镜(TEM)、原子力显微镜(AFM)对所制备的GQDs进行形貌表征, GQDs的粒子大小均一, 为单层石墨烯. 通过傅里叶变换红外光谱(FTIR)、荧光光谱(PL)、紫外可见吸收光谱(UV-vis)、X 射线衍射光谱(XRD)对所制备的GQDs进行性质测定, 发现GQDs可以发出黄色荧光, 量子产率为14%, 毒性低、具有良好的水溶性、荧光稳定性和生物兼容性, 可顺利进入细胞, 在肿瘤细胞的成像研究方面具有广泛的应用前景.     

ZnO-离子液体功能化的石墨烯量子点的制备及荧光性能

利用水热法制备了ZnO-1-丙胺基-3-甲基咪唑氯离子液体功能化的石墨烯量子点溶液,通过紫外-可见吸收光谱、红外吸收光谱和透射电镜对其进行了表征.通过研究各种因素对ZnO-离子液体功能化的石墨烯量子点的荧光发射光谱的影响,发现Cr_2O_7~(2-)对ZnO-离子液体功能化的石墨烯量子点有荧光猝灭现象.实验结果表明,在优化的实验条件下,pH=5.0,Cr(Ⅵ)浓度为1.0×10~(-7)～1.6×10~(-6 )mol·L~(-1)时,Cr(Ⅵ)对ZnO-离子液体功能化的石墨烯量子点的荧光猝灭呈线性,其线性方程为F/F_0=0.969 5-0.008 4c,R=0.998 8,检出限为7.6×10~(-2)μmol·L~(-1).     

混合相二氧化钛石墨烯复合物的制备及光催化性能

采用水热法制备了一系列混合相二氧化钛-石墨烯(TrG)的复合物, 并考察了石墨烯的用量对降解污染物甲基蓝的影响. 采用X射线衍射(XRD), 傅里叶变换红外(FTIR)光谱, 高分辨透射电镜(HRTEM), 拉曼光谱,紫外-可见漫反射吸收光谱(UV-Vis DRS), X射线光电子能谱(XPS)和比表面积(BET)等测试手段对复合材料进行表征. 结果表明, 复合材料中TiO₂为棒状的混合相, 且均匀分散在石墨烯表面. 由于石墨烯良好的吸光性能,混合相中的异质结和复合物的良好光电子传递能力以及高比表面积, 复合材料具有较高的光催化活性. 所制备的TrG复合材料在紫外光下降解甲基蓝的催化活性均高于纯TiO₂, 且当氧化石墨烯负载量为0.8% (质量分数,w)时, 复合材料TrG具有较好的光催化效果.     

乙醇胺功能化石墨烯的制备与表征

乙醇胺在温和条件下与氧化石墨烯反应, 然后经水合肼还原得到功能化的石墨烯. 干燥的功能化石墨烯经超声处理后, 可稳定分散于水、乙醇、丙酮和N,N二甲基甲酰胺(DMF)等溶剂中. 原子力显微镜(AFM)、透射电镜(TEM)分析表明功能化石墨烯平均厚度为3～4 nm. 傅里叶变换红外光谱(FTIR)、X射线光电子能谱(XPS)、X射线衍射(XRD)对功能化石墨烯的结构分析表明: 乙醇胺与氧化石墨烯发生了化学反应, 并通过共价键连接到石墨烯的六元环上. TG结果表明功能化石墨烯的热稳定性比氧化石墨烯有所提高, 但低于还原氧化石墨烯.     

氧化石墨烯/聚电解质层层自组装制备单价离子选择性膜

采用层层自组装法在改性聚丙烯腈(PAN)膜表面交替沉积聚乙烯亚胺(PEI)和聚丙烯酸-氧化石墨烯(PAA-GO)混合液,制得了单价离子选择性复合膜。X射线衍射(XRD)测试结果表明成功合成了氧化石墨烯(GO)并在复合膜中均匀分散。扫描电镜(SEM)观察结果证实了多层聚电解质PEI/PAA-GO成功地组装在基膜上,并用紫外-可见(UV-Vis)光谱进一步证实了组装过程的均匀性和连续性。接触角和性能测试表明加入GO后,复合膜的亲水性和单价阳离子的选择性明显增大。这种高通量、高选择性的防污复合膜在分离和水的软化方面有很好的应用前景。     

石墨烯氧化物薄膜电极的光电化学特性

采用浸渍-提拉法制备了一系列石墨烯氧化物(GO)薄膜,并通过X射线衍射(XRD),扫描电镜(SEM),傅里叶变换红外光谱,紫外-可见吸收光谱和光电化学测量等技术对样品进行了表征.在GO电极上观察到阴极光电流,且光电流密度受薄膜的厚度影响.GO薄膜电极厚度为27nm时,光电流密度为0.25μA·cm-2.此外,GO电极的光电响应还受紫外光照影响,随着紫外光照时间的延长,阴极光电流逐渐减小.该工作提供了简便的通过控制薄膜厚度或紫外光照时间来控制GO薄膜半导体光电化学性能的方法.     

一种有效的制备聚乙二醇修饰氧化石墨烯的方法

为提高氧化石墨烯(GO)的生物相容性从而扩展其在高性能生物材料制备中的应用,采用甲苯-2,4-二异氰酸酯作为桥联剂,制备了四臂星型聚乙二醇修饰氧化石墨烯(GO-TDI-sPEG),该产物在水中仍然可以稳定分散.采用傅里叶红外光谱(FTIR)、拉曼光谱(Raman)、X-射线衍射(XRD)、原子力显微镜(AFM)、透射电子显微镜(TEM)和热重分析(TGA)对接枝产物进行表征.产物在2861 cm-1和1093 cm-1处出现的特征红外吸收表明sPEG已接枝到GO上.产物的Raman光谱中D模与G模信号变弱,且ID/IG值变化不大,说明sPEG改性后的氧化石墨物理结构没有发生变化.XRD曲线上产物衍射峰消失,表明经聚合物修饰后氧化石墨被完全剥离.TGA数据表明原始GO在约160℃开始发生热失重,经修饰后,大约在260℃开始热失重,热稳定性增加了约100℃.由TEM图片可以观察到GO及改性石墨烯产物剥离程度较高,且片上分布有较多聚合物点.且AFM图片显示GO的平均厚度大约为0.85 nm,接上聚合物后部分厚度增加到约1.2 nm.     

高分散Mn-KIT-6催化剂的制备及催化性能研究

以介孔分子筛KIT-6为载体, 采用溶液浸渍法将乙酰丙酮锰(III)的糠醇溶液灌注到KIT-6的孔道内, 一定条件下将糠醇碳化后再焙烧脱除碳, 制得Mn-KIT-6催化剂. 通过X射线衍射(XRD)|氮气物理吸附-脱附|紫外-可见吸收光谱(UV-Vis)|傅里叶变换红外光谱(FT-IR)|电感耦合等离子发射光谱(ICP-AES)|透射电镜(TEM)|氨气-程序升温脱附(NH₃-TPD)及X射线光电子能谱(XPS)等方法对样品进行了表征. 结果表明锰在KIT-6孔道内部高度分散, 同时催化剂保持高度有序的孔道结构、较大的比表面积和孔容. 正丁醇和乙酸的催化酯化反应结果表明, 该催化剂具有很高的催化活性, 反应4 h后乙酸正丁酯的产率高达97.3%, 使用5次后催化剂依然具有较高的活性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.