超声辅助离子液体分散液相微萃取-高效液相色谱法测定废水中雌激素的研究

将离子液体、分散液相微萃取与超声萃取技术结合,采用疏水性离子液体1-丁基-3-甲基咪唑六氟磷酸盐([C4 MIM][PF6])为萃取剂,建立了超声辅助离子液体分散液相微萃取-高效液相色谱法分析废水中3种雌激素物质(己烯雌酚、双烯雌酚、己烷雌酚)方法.试验采用50μL的离子液体,考察了溶液体积、溶液pH值、超声时间、静置时间、离心时间等因素对富集效果的影响.最佳的萃取条件为:溶液体积为6 mL,甲醇体积0.3 mL,溶液pH值为2.0,超声时间6min,静置时间30min,离心时间10 min.在优化的萃取条件下,3种雌激素的富集倍数可达到96.8～112.4倍;方法的线性范围为0.5-100.0μg/L;检出限为0.25～0.50μ/L.对浓度为5.0μg/L的3种物质测定6次的相对标准偏差为9.2%～10.8%.     

离子液体单滴顶空微萃取系列乙酯的性能及其气相色谱分析

通过改进气相色谱内衬管,避免离子液体进入色谱柱,实现了离子液体单滴微萃取与气相色谱的联用.利用改进装置考察了离子液体[C4MIM][PF6]对乙酸乙酯、丙酸乙酯、丁酸乙酯、戊酸乙酯、己酸乙酯和苯甲酸乙酯6种乙酯化合物的顶空萃取及气相色谱分析.在优选条件下,即以0.1 μL离子液体在0.36 g/mL NaCl溶液中,以0.1 μL离子液体40 ℃萃取分析物25 min后,气化室解吸1 min,得到富集倍数为3～141, 检出限为0.25～40 μg/L,线性范围约两个数量级,相对标准偏差为3%～8%.本方法装置简单,操作快捷,灵敏度较高,在试样前处理方面有广泛的应用价值.     

疏水性离子液体萃取光甘草定

选择了疏水性的离子液体1-丁基-3-甲基咪唑六氟磷酸盐([C4mim][PF6])和亲水性的离子液体1-丁基-3-甲基咪唑四氟硼酸盐([C4mim][BF4])作萃取剂,对光甘草定提取液进行了萃取,并对离子液体的再生进行了研究。结果表明,亲水性的离子液体和光甘草定提取液无法分层,而疏水性的离子液体分层清晰,并得疏水性离子液体[C4mim][PF6]萃取光甘草定最佳萃取工艺条件为:相体积比为1∶2.5(V/V),pH值为7,萃取温度为45℃,萃取时间为30 min,此时光甘草定的萃取率达85.49%。离子液体再生选用2 mol.L-1氢氧化钠和无水乙醇混合液做反萃剂,可得光甘草定的回收率大于90%,离子液体循环使用5次,萃取率未见明显下降。     

离子液体萃取阿魏酸和咖啡酸的性能研究

以1-甲基-3-丁基咪唑六氟磷酸盐([C4mim][PF6])和1-甲基-3-己基咪唑六氟磷酸盐([C6mim][PF6])离子液体为萃取剂,采用紫外分光光度法研究了溶液pH值、温度、相比率及盐的种类和浓度对其萃取阿魏酸和咖啡酸效率的影响,考察了被萃取物的回收及离子液体的循环使用,探讨了两种离子液体替代传统有机溶剂阿魏酸和咖啡酸的可能性。实验结果表明:萃取温度和无机盐的种类及浓度对FA和CA萃取效率的影响较小;水相pH值对萃取效率有较大的影响,萃取FA适宜pH应小于3.67,萃取CA适宜pH应小于3.71;被萃取物浓度增大,萃取效率降低,而相体积比增大其萃取效率升高;两种离子液体对FA和CA的萃取效率[C4mim][PF6]大于[C6mim][PF6],同种离子液体对FA的萃取效率大于CA;在萃取相中的FA和CA可定量回收,且被萃取物中离子液体的残留[C6mim][PF6]小于[C4mim][PF6],离子液体可循环使用。     

离子液体均相液液微萃取-高效液相色谱法测定水中痕量双酚A

建立了离子液体均相液液微萃取-高效液相色谱法测定水中痕量双酚A的分析方法。通过一定浓度的加标回收率实验,优化了离子液体均相液液萃取的条件和高效液相色谱仪的条件。对影响萃取和样品制备条件的因素进行了优化,其中萃取条件包括离子液体种类、体积、NH4PF6的量、萃取时间和离心时间,而样品制备的条件包括pH和NaCl含量。优化的最佳条件是:90μL离子液体1-己基-3-甲基咪唑四氟硼酸盐离子液体([C_6MIM][BF_4])作萃取剂,NH_4PF_6和[C_6MIM][BF_4]的摩尔比为6:1,萃取1.0 min,离心8.0 min,调节样品溶液的pH为8.0,NaCl质量分数为6.0%。在此条件下,双酚A在1.25~100μg/L范围内线性良好,相关系数大于0.999,回收率为86.5%~118.8%,相对标准偏差为2.5%~8.5%,定量限为1.25μg/L。     

离子液体和氯代溶剂分散液-液微萃取/高效液相色谱法联用富集和分析环境水样中酞酸酯类污染物的对比研究

以4种室温离子液体和4种氯代溶剂为萃取剂,与高效液相色谱(HPLC)联用,对比研究了分散液-液微萃取(DLLME)对5种痕量酞酸酯类化合物(PAEs)的富集分离性能。以1-辛基-3-甲基咪唑六氟磷酸盐([OMim][PF6])和建议研究四氯化碳替代品为典型萃取溶剂优化了萃取条件。结果表明,在1.00～100μg/L范围内色谱峰面积与PAEs浓度成良好的线性关系(相关系数>0.995);对于10.0μg/L加标混合样品,平均加标回收率88.2%～103.3%,RSD在2.1%～6.8%之间(n=5),LOD在0.01～0.08μg/L范围内(S/N=3)。与四氯化碳相比,[OMim][PF6]作为DLLME的萃取溶剂对PAEs的富集倍数较高,水相盐效应影响较小。超声波辅助微萃取(USA)可在2 min达到平衡,建立的USA-DLLME-HPLC方法可用于黄河水样和城生活区污水样品中痕量PAEs的富集分离和测定。     

环境水样中己烯雌酚与双烯雌酚的离子液体分散液-液微萃取/高效液相色谱法测定

以离子液体([Omim][PF6])为萃取剂,采用冷诱导分散液-液微萃取对环境水样中的己烯雌酚和双烯雌酚残留进行富集.优化后的萃取条件:在pH 3.0的条件下,以50 μL离子液体为萃取剂,0.8 mL甲醇为分散剂,采用反相 Extend-C18柱(5 μm, 250 mm×4.6 mm),流动相为水-甲醇(体积比40 ∶ 60),流速:1.0 mL/min,柱温:35 ℃,检测波长:245 nm.在优化的萃取条件下,己烯雌酚和双烯雌酚的线性范围均为2.5 ～200 μg/L,检出限(S/N=3)为80 ng/L.应用于环境水样中己烯雌酚和双烯雌酚的检测,加标回收率为93% ～98%,相对标准偏差为3.0% ～5.4%,建立的方法简单、环保.     

超声辅助离子液体液相微萃取-高效液相色谱法分析水样中加替沙星或氟罗沙星

建立了一种采用离子液体1-己基-3-甲基咪唑六氟磷酸([C6mim][PF6])为萃取剂,超声辅助离子液体液相微萃取-高效液相色谱法分析水样中加替沙星和氟罗沙星的方法。 实验考察了溶液酸度、离子液体用量等因素对萃取的影响。在pH值分别为3.3、2.1的加替沙星和氟罗沙星水样中,加入0.4 mL [C6mim][PF6],超声,离心,离子液体相直接用于HPLC进行分析。 该方法的线性范围为0.5~50 mg/L,测定加替沙星和氟罗沙星的相对标准偏差(n=5)为2.80%和5.93%,二者的检出限分别为0.46、0.97 μg/L,该方法萃取水样中加替沙星的加标回收率为80.5%~89.5%,氟罗沙星的加标回收率可达93.3%~99.0%。     

[C4mim][PF6]和[C4mim][NTf2]离子液体辐射诱导的相行为及荧光行为变化

离子液体因其低挥发性, 高热稳定性及优良的萃取性能被认为是萃取分离放射性核素的新一代绿色溶剂, 而研究离子液体本身的辐射效应是其实际应用的重要前提. 本文以60Co为辐射源, 系统研究了γ辐照对两种常见的憎水性咪唑离子液体1-丁基-3-甲基咪唑六氟磷酸盐([C4mim][PF6])和1-丁基-3-甲基咪唑三氟甲基磺酰胺酸盐([C4mim][NTf2])的相行为及荧光行为的影响. 在相行为方面, γ辐照使离子液体的结晶驰豫时间增加, 导致其低温结晶延迟. 在荧光行为方面, γ辐照后离子液体的荧光光谱保持原有的“红边效应(red edge effect)”, 但随吸收剂量增加, 光谱整体发生红移(最大移动幅度达150 nm). 并且这种“红边效应”在辐照后离子液体的乙腈稀释剂中仍然存在, 且随稀释倍数增加光谱整体发生蓝移. [C4mim][PF6]和[C4mim][NTf2]离子液体辐照后的这种相行为及荧光行为的变化可归因于辐照对其阴阳离子空间相关性(缔合行为)的影响.     

新型对称烷基咪唑离子液体介质中酶催化合成l-乙酸薄荷酯

设计合成三种新型对称烷基咪唑六氟磷酸盐离子液体——1,3-二正丁基咪唑六氟磷酸盐([DnBIM][PF6]), 1,3-二异丁基咪唑六氟磷酸盐([DiBIM][PF6])和1,3-二仲丁基咪唑六氟磷酸盐([DsBIM][PF6]). 以脂肪酶pseudomonas cepacia催化l-薄荷醇和乙酸酐的酯化过程为模型反应, 分别考察不同介质中酶的活性、反应性和稳定性, 结果表明作为反应介质三种新型离子液体均优于经典离子液体1-正丁基-3-甲基咪唑六氟磷酸盐和有机溶剂正己烷. 在三种新的离子液体中, [DiBIM][PF6]具有最好的亲生物性而被选择作为模型反应介质. 此外, 影响l-薄荷醇转化率的各种因素(包括反应温度、底物投料比、离子液体用量和含水量)及酶的重复利用性也被详细研究. 在最佳反应条件下, l-薄荷醇转化率达到97.4%, 酶促反应速度、平衡转化率和半衰期分别是正己烷中的12.7, 4.6和15.1倍. 脂肪酶重复使用10次后催化活性没有明显减少. 由于三种新型离子液体互为同分异构体, 以上事实还表明除憎水性和亲核性以外离子液体的空间构型也是影响酶行为的一个重要因素.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.