Alkylamine sensing using langmuir-blodgett films of n-alkyl-N-phenylamide-substituted zinc porphyrins

Two porphyrin compounds, zinc(II) 5,10,15,20-tetrakis(3,5,5-trimethyl- N-phenylhexanamide)porphyrin and zinc(II) 5,10,15,20-tetrakis(2,2-dimethyl- N-phenylpropanamide)porphyrin, have been investigated as possible candidates for the detection of alkylamines. UV-visible spectroscopy has shown that their solution absorption spectra are significantly modified upon interaction with a range of organic analytes, including acetic acid, butanone, ethylacetate, hexanethiol, octanal, octanol, alkylamines, and trimethylphosphite. Large spectral changes are observed for the family of alkylamines as a result of the specific affinity between zinc and the amine moiety. Langmuir-Blodgett (LB) films of the porphyrins have been fabricated in order to assess their solid-state sensing capability toward amines. The surface pressure-area (Pi- A) isotherms reveal a clear three-phase Langmuir film behavior and show that these monolayer films may be compressed to a relatively high surface pressure ( approximately 40-50 mN m (-1)). The isotherm data alongside molecular modeling suggest a relatively flat orientation of the porphyrin rings of both compounds: that is, a mutually parallel alignment of the plane of the porphyrin ring and that of the water surface. LB films deposited at 15 mN m (-1) have been exposed to alkylamine vapor (carried by N 2). A red shift and increase in intensity of the Soret band absorbance is observed which can be reversed by flowing pure N 2 over the gently heated sample (60 degrees C) after exposure. Primary amines were expected to invoke the greatest sensing response due to (i) their larger association constants with these porphyrins compared to secondary and tertiary amines and (ii) the ease of diffusion of amines which is expected to follow the order primary > secondary > tertiary due to the steric hindrance arising from the bulky secondary and tertiary amines. However, the magnitude of the absorbance change is largest for exposure to the secondary amines, dipropylamine and dibutylamine, for both porphyrins, compared to primary and tertiary amines. This trend follows that observed when the amines were added to solutions of the porphyrins. The rate of response of the porphyrin LB films falls as the molecular weight of the diffusing alkylamine increases. Furthermore, a greater rate of response is observed for the phenylhexanamide porphyrin compared to the phenylpropanamide porphyrin due to its lower molecular density within the LB film and therefore more porous structure.     

修饰LB膜法制备的PEDOT薄膜对HCl气体气敏性的影响

以二十烷酸(AA)LB膜为模板, 通过3,4-乙烯二氧噻吩(EDOT)单体在LB膜亲水基团间聚合, 采用垂直拉膜方式在叉指电极上制备了不同层数的AA/PEDOT膜, 并对HCl气体在AA/PEDOT复合LB膜中的作用进行研究, 结果表明, 膜厚、处理温度、拉膜膜压对AA/PEDOT复合LB膜的HCl气体敏感性能有不同程度的影响. 在较小气体体积分数范围(20～60 μL/L)内, AA/PEDOT多层有序膜对气体表现出非线性响应特性, 而在较高浓度范围内则表现出线性响应特性. AA/PEDOT复合LB膜对30 μL/L HCl气体的响应时间约为20 s, 远快于普通PEDOT旋涂膜(约为80 s), 同时在膜压达到45 mN/m时, AA/PEDOT膜的敏感性能反而下降. 敏感机理解释为电子在PEDOT共轭系统和氧化性气体间的转移.     

Optical detection of chlorine gas using LB films of a zinc porphyrin dimer

We report on the optical response of the zinc porphyrin dimer 1 to gaseous chlorine. In situ optical measurements have been made on organized thin films of 1 during exposure to a stream of chlorine gas at low concentrations (0.5–10 ppm). Typical response time at 2 ppm for the dimer monolayer is 35 s for 50% loss in monitored absorbance. Response-controlling factors such as LB deposition conditions, substrate type, target gas concentration, film ageing and heat treatment have been investigated with a view to developing a prototype chlorine-sensing device to be used for personal safety purposes. Rate constants for the response processes have been deduced.     

Dis-aggregation of an insoluble porphyrin in a calixarene matrix: characterization of aggregate modes by extended dipole model

In this paper, the different aggregation modes of a water-insoluble porphyrin (EHO) mixed with an amphiphilic calix[8]arene (C8A), at the air-water interface and in Langmuir-Blodgett (LB) film form, are analyzed as a function of the mixed composition. The strategy used to control the EHO aggregation has consisted of preparing mixed thin films containing EHO and C8A, in different ratios, at the air-water interface. Therefore, the increase of the C8A molar ratio in the mixed film diminishes the aggregation of the EHO molecules, although such an effect must be exclusively related to the dilution of the porphyrin. The reflection spectra of the mixed C8A-EHO films registered at the air-water interface, show a complex Soret band exhibiting splitting, hypochromicity and broadening features. Also, during the transfer process at high surface pressure, it has been shown that the EHO molecules are ejected from the C8A monolayer and only a fraction of porphyrin is transferred to the solid support, in spite of a complete transfer for the C8A matrix. The complex structure of the reflection spectra at the air-water interface, as well as the polarization dependence of the absorption spectra for the mixed LB films, indicate the existence of four different arrangements for the EHO hosted in the C8A matrix. The aggregate formation is governed by two factors: the attraction between the porphyrin rings which minimizes their separation, and the alkyl chain interactions, that is, hydrophobic effect and/or steric hindrance which determine and restrict the possible aggregation structures. By using the extended dipole model, the assignment of the spectral peaks observed to different EHO aggregates is shown.     

The incorporation of C_(60) in cavities of 5,10,15,20-tetra-4-oxy(2-stearic acid)phenyl porphyrin in LB film

The structure and properties of mixed monolayer or LB film of 5,10,15,20-tetra-4-oxy(2-stearic acid)phenyl porphyrin/C60 were studied. A isotherms and small angle X-ray diffraction (SAXD) results show that C60 molecules were incorporated into the cavities of por-phyrin molecules in mixed monolayer and LB film . UV-vis spectra of mixed LB films show that the absorption intensity of porphyrin varied compared with pure porphyrin film, probably arising from the interactions between C60 and porphyrin ring. C60 molecules in mixed systems are well-dispersed. The TPP(CO2H)/C60 mixed LB film is a kind of two-dimensional host-guest system.     

十六烷基三辛基铵静电吸附氯金酸的Langmiur-Blodgett膜及其修饰聚氯乙烯液膜金离子选择性电极的研究

首次尝试用Langmiur-Blodgett(LB)技术修饰PVC液膜离子选择性电极,在PVC液膜表面上制得十六烷基三辛基铵-氯金酸LB膜,明显改善了PVC液膜金离子选择性电极的某些工作性能。电极线性响应范围为1×10~(-2)～1×10~(-7)mol/L,对常见的9种阳离子和4种阴离子的干扰能力明显的增强,响应速度也有所提高。若能改进挂膜方式,可望进一步改善有关性能。     

Langmuir-Blodgett films of a cationic zinc porphyrin-imidazole-functionalized fullerene dyad: formation and photoelectrochemical studies

Electron donor-acceptor dyad ensembles of a water-soluble cationic zinc porphyrin (viz., zinc tetrakis(N-methylpyridinium)porphyrin tetrachloride, Zn(TMPyP)) and a C60 derivative that bears an imidazole ligand (viz., 2-(phenylimidazolyl)fulleropyrrolidine, C60im) were assembled during the formation of Langmuir and then Langmuir-Blodgett (LB) films. Surface pressure versus surface area isotherms and surface pressure time profiles, as well as Brewster angle microscopic images documented that the Langmuir films formed were remarkably stable. Subsequently, these Langmuir films were transferred onto different solid substrates, by using the LB technique, for spectroscopic and photoelectrochemical characterization. The UV-vis spectroscopic investigations confirmed that the water-soluble Zn(TMPyP) was, indeed, transferred together with C60im in the LB films. Upon visible light illumination of these LB films, deposited on the ITO transparent conductive supports, a photocurrent generated in the C60im-Zn(TMPyP) system is ascribed to an efficient photoinduced electron transfer from the electron donor, porphyrin singlet excited-state to the electron acceptor, C60. Overall, internal photon-to-current efficiency, IPCE, of the photoanodic current generation (with ascorbate as a sacrificial electron donor) in the ITO/C60im-Zn(TMPyP)/ascorbate/Pt construct is over 5x larger than that of the photocathodic system (with methyl viologen, MV2+, as a sacrificial electron acceptor) in the ITO/Zn(TMPyP)-C60im/MV2+/Pt construct. Highly ordered film stacking favors vectorial electron transfer within the dyad, giving rise to the highest IPCE values of 2.5% determined for a photoanode that was composed of around 20 monolayer films.     

5,10,15,20-四-(4-N,N,N-二甲基十六烷基氨基苯基)卟啉LB膜结构的研究

研究了两亲性卟啉5,10,15,20-四-(4-N,N,N-二甲基十六烷基氨基苯基)卟啉(TDMC₁₆PP)在气/液界面上的成膜性能,制备了其多层LB膜。用UV-Vis吸收光谱、荧光光谱、偏振UV-Vis吸收光谱和小角X射线衍射对LB膜进行了测试表征。结果表明:两亲性卟啉TDMC₁₆PP具有良好的成膜性能,其LB膜性质稳定,有较好的结构均匀性和周期性。在LB膜内,脂肪链并不是直立的,卟啉大环平面与基片平面成42.5°排列。     

Gold nanoparticle enhanced charge transfer in thin film assemblies of porphyrin-fullerene dyads

Photoinduced vectorial electron transfer in a molecularly organized porphyrin-fullerene (PF) dyad film is enhanced by the interlayer charge transfer from the porphyrin moiety of the dyad to an octanethiol protected (dcore approximately 2 nm) gold nanoparticle (AuNP) film. By using the time-resolved Maxwell displacement charge (TRMDC) method, the charge separation distance was found to increase by 5 times in a multilayer film structure where the gold nanoparticles face the porphyrin moiety of the dyad, that is, AuNP|PF, compared to the case of the PF layer alone. Films were assembled by the Langmuir-Blodgett (LB) method using octadecylamine (ODA) as the matrix compound. Atomic force microscopy (AFM) images of the monolayers revealed that AuNPs are arranged into continuous, islandlike structures and PF dyads form clusters. The porphyrin reference layer was assembled with the AuNP layer to gain insight on the interaction mechanism between porphyrin and gold nanoparticles. Interlayer electron transfer was also observed between the AuNPs and porphyrin reference, but the efficiency is lower than that in the AuNP|PF film. Fluorescence emission of the reference porphyrin is slightly quenched, and fluorescence decay becomes faster in the presence of AuNPs. The proposed mechanism for the electron transfer in the AuNP|PF film is thus the primary electron transfer from the porphyrin to the fullerene followed by a secondary hole transfer from the porphyrin to the AuNPs, resulting in an increased charge separation distance and enhanced photovoltage.     

冠醚和卟啉与花生酸混合单分子膜行为研究

本文将3'-正十五烷基苯并15-冠-5和六种无脂链难于直接成膜的四苯基卟啉与花生酸混合形成单分子膜。结果表明, 冠醚被嵌进而卟啉被挤出花生酸单分子层。卟啉-花生镉LB膜的可见吸收光谱指出卟啉分子成团聚集。扫描电镜观察了卟啉-花生酸镉混合LB膜的表面形貌, 在膜表面上无金涂层时直接测到了混合膜的相分离。     

导电聚合物超薄膜的制备及性能表征

采用修饰LB膜法制备了导电聚合物聚-3,4-乙烯二氧噻吩/硬脂酸(PEDOT/SA)复合超薄膜. 将硬脂酸(SA)/FeCl3 LB膜暴露于EDOT单体气氛中, EDOT 单体在多层膜中聚合, 制备了PEDOT/SA多层复合LB膜. 紫外-可见光-近红外(UV-Vis-NIR)吸收光谱和X射线光电子能谱(XPS)分析表明EDOT单体在多层膜中发生聚合并生成PEDOT导电聚合物. 扫描电子显微镜(SEM)分析显示生成的PEDOT导电聚合物颗粒分散于硬脂酸LB膜中, 被LB 膜所包裹. 二次离子质谱(SIMS)及XPS分析还发现S元素含量随LB 膜的深度变化而变化, 表明PEDOT 较好地分散于多层膜中. 采用四探针电导率仪对复合多层膜的电导率进行了测试, 结果显示60 层复合LB 膜的电导率为2.6 S·cm-1, 比普通PEDOT薄膜的电导率高一个数量级, 且表现出较好的掺杂/脱掺杂能力. 研究还发现复合膜电导率与薄膜在EDOT 单体中处理时间有关, 处理时间至120 min 后电导率达到最大值并趋于稳定, 氧化剂浓度较低可能影响EDOT在LB膜中的聚合反应速率. 对复合LB 膜的气敏特性进行了分析, 发现在较低气体浓度范围(φ<30×10^-6), PEDOT 复合LB 膜有较快的反应速率, 气敏性与气体浓度呈非线性. 在较高浓度范围(φ=(30-120)×10^-6), 气敏性与浓度呈较好的线性关系. PEDOT复合LB膜对HCl气体表现出较好的响应恢复特性. 同时对PEDOT 复合膜相关的导电机理及气体敏感机理进行了分析.     

Modeling the kinetics of gas adsorption in multilayer porphyrin films

A kinetic model is proposed to describe the diffusion and adsorption behavior of gas in multilayer films. Numerical solutions are attained on time scales of seconds using a finite differencing approximation to the kinetic equations. Predictions of this model are compared to experimental data for the case of NO2 diffusing through a porphyrin film. The model predicts a binding energy for the NO2 porphyrin interaction of 0.72 eV. It also predicts that for this system diffusion is the limiting factor for the adsorption response time of the film, although the recovery time is determined by both the diffusion coefficient and NO2 binding energy. Comparison with experiment gives a predicted diffusion coefficient of approximately 10(-14) m2.s-1.     

Photoinduced electron transfer in Langmuir-Blodgett monolayers of porphyrin-fullerene dyads

A series of electron donor-acceptor (DA) dyads, composed of a porphyrin donor and a fullerene acceptor covalently linked with two molecular chains, were used to fabricate solid molecular films with the Langmuir-Blodgett (LB) technique. By means of the LB technique, the DA molecules can be oriented perpendicular to the plane of the substrate. In DHD6ee and its zinc derivative hydrophilic groups are attached to the phenyl moieties in the porphyrin end of the molecule; while in the other three dyads, TBD6a, TBD6hp, and TBD4hp, the hydrophilic groups are in the fullerene end of the molecule. This makes it possible to alternate the orientation of the molecules in two opposite directions with respect to the air-water interface and to fabricate molecular assemblies in which the direction of the primary photoinduced vectorial electron transfer can be controlled both by the deposition direction of the LB monolayer and by the selection of the used DA molecule. This was proved by the time-resolved Maxwell displacement charge measurements. The spectroscopic properties of the DA films were studied with the steady-state absorption and fluorescence methods. In addition, the time correlated single photon counting technique was used to determine the fluorescence properties of the dyad films.     

Interaction between nitric oxide and lipid-like DDPA LB film investigated with SHG and AFM

Interactions between Nitric oxide (NO) and DDPA Langmuir-Blodgett (LB) film are investigated with second harmonic generation (SHG) and atomic force microscopy (AFM). It has been found that the adsorption of NO molecules on DDPA LB film only changes the value of the second-order susceptibility of the DDPA molecule on film but not its orientation.     

长碳链季铵类卟啉钴配合物的合成及其LB膜和气敏性质

四－（4－N，N，N－二甲基）卟啉（TDMAPP）与溴代正十六烷反应得到溴化四－（4－N，N，N－二甲基，十六烷基氨基苯）卟啉（TDMHAPPBr)并制得其钴的配合物，两者均具有良好的成膜性。电子吸收光谱表明LB膜与成膜前固体物分子排列规整性不同，钴配合物对敢有较好的敏感性和良好的选择性，其响应和恢复时间都较短。     

Dicyanopyrazine-linked porphyrin Langmuir-Blodgett films

We investigated the influence of arachidic acid/cadmium dication (AA/Cd(2+)) as a transfer promoter for the deposition of dicyanopyrazine-linked porphyrin (2-DCPP) Langmuir-Blodgett (LB) films on both hydrophobic and hydrophilic substrates. In the case of LB deposition on a hydrophilic substrate, the presence of AA/Cd(2+) does not improve 2-DCPP LB deposition. The poor transfer in the case of the hydrophilic surface is believed to be due to 2-DCPP not wetting the surface during the down-stroke deposition, and this is not improved by the transfer agent. However, on a hydrophobic substrate, deposition of 2-DCPP is significantly improved by the presence of AA/Cd(2+). Comparison of the UV-visible spectrum of a 2-DCPP LB film with that of 2-DCCP dissolved in chloroform reveals that the Soret and Q bands for the 2-DCPP LB film are broadened and red-shifted due to aggregation of porphyrin rings in the LB film. UV-visible spectral changes and ellipsometry as a function of the number of deposition layers suggest continuous transfer of 2-DCPP/AA onto the hydrophobic substrate and reproducibility in the deposition process. The Soret and Q bands of the 2-DCPP LB film upon acid vapor exposure have also been investigated, and these measurements may have chemical sensor applications.     

Spectroscopic and optical characterization of porphyrin chromophores incorporated into ultrathin polyimide films

Polyamic acid (PAA) containing free-base porphyrin and zinc(II) porphyrin chromophores was synthesized by copolymerization of diphenylether-type tetracarboxylic dianhydride and diamines. The monolayer of the alkylamine salts of PAA (PAASs) at the air/water interface was deposited on solid substrates by the Langmuir-Blodgett (LB) technique. The PAAS LB films thus obtained were converted to polyimide (PI) LB films by chemical treatment. The fluorescence of porphyrin moieties in the PI LB film was observed, because of the weak electron-accepting properties of the diphenylether unit. Therefore, the photophysically important processes, such as photoinduced electron transfer, excitation energy transfer, and excitation energy migration could be investigated in relation to the layered nanostructures of the ultrathin PI films. The fluorescence spectrum suggested that the aggregation of porphyrin moieties in the PI LB films was effectively prevented by the use of polymeric films. The surface plasmon (SP) measurement showed that the thickness of the monolayers was 0.9-1.0 nm for PAAS films and 0.32-0.40 nm on average for PI LB films. The absorption dichroism of the Soret band of porphyrin indicated that porphyrin moieties in the PAAS and PI LB films are oriented in parallel with the substrate. These results showed that the orientation and the spatial distribution of porphyrin units can be efficiently regulated in the PI LB films in a nanometer dimension.     

Anodic electrodeposition of NiTSPP from aqueous basic media

The oxidative electrodeposition of NiTSPP (tetrakis(4-sulfonatophenyl) Ni porphyrin) on ITO electrode from 0.1 M NaOH aqueous solution has been studied, and UV-visible and reflection FTIR spectroscopies have been used to analyze the composition of such film. By use of UV-vis spectroscopy, small absorbance of the film and an almost nulling effect on the Soret band of the porphyrin along the Ni(III)/Ni(II) redox process were observed. The reflection FTIR spectroscopy detected the presence of Ni-OH groups in the reduced film and as well the state of the porphyrin molecules as radical cation. Moreover, the porphyrin has been quantified by means of the area of the vibration bands assigned to the sulfonate groups by using as reference a Langmuir-Blodgett film containing a known surface concentration of NiTSPP. These results lead us propose the formation of a conductor salt by electrocrystallization, with stoichiometries TSPP/Ni(II)(OH)2 and TSPP/Ni(III)OOH, for its reduced and oxidized forms, respectively. In these two forms, the porphyrin rings will be present as radical cation, which may be stabilized through its dimerization or polymerization.     

A comparative Langmuir-Blodgett study on a set of covalently linked porphyrin-based amphiphiles: a detailed atomic force microscopic study

A set of covalently linked phenyl-amidophenyl-substituted porphyrin amphiphiles with n-C15H31 tails have been synthesized and completely characterized. These amphiphiles form good Langmuir-Blodgett (LB) films at the air/water interface. Mean molecular areas for the series were measured from the isotherms and found to increase as the number of aliphatic chains increased from one to four. No influence of the subphase pH was observed on the isotherms. LB films can be transferred successfully onto different solid surfaces. The LB films were characterized using tapping mode atomic force microscopy (AFM). Bis-, tris-, and tetra-substituted porphyrins were found to be fairly good film-forming amphiphiles, whereas irregular aggregates were seen in the case of the monosubstituted porphyrin amphiphile. Multilayers were also formed with tetra-substituted amphiphiles on mica. Detailed AFM studies of tetra-substituted amphiphiles have been carried out to investigate the effect of preparation procedure and solid substrates on film formation and transfer. The absorption and fluorescence spectra for the amphiphiles in solution and LB films deposited onto mica and glass were recorded, which demonstrated the successful transfer of LB films onto the substrates and provided more information about the arrangement of porphyrin molecules within the LB films. For comparison, self-assembled monolayers (SAMs) and the cast thin films of the amphiphiles were prepared and characterized.     

8,10-二炔二十五碳酸LB膜的聚合

Langmuir-Blodgett膜(LB膜)具有特殊的功能和生物活性,在现代高技术中有广泛的应用^[1]。本文合成了一个长链炔酸-8,10-二炔二十五碳酸,并研究其LB膜的聚合。