Development of a 4–15 μm infrared GaAs hyperspectral QWIP imager

In the on-going evolution of GaAs quantum well infrared photodetectors (QWIPs) we have developed a four band, 640 × 512, 23 μm × 23 μm pixel array which we have subsequently integrated with a linear variable etalon (LVE) filter providing over 200 spectral bands across the 4–15.4 μm wavelength region. This effort was a collaboration between NASA’s Goddard Space Flight Center (GSFC), the Jet Propulsion Laboratory (JPL) and the Army Research Laboratory (ARL) sponsored by the Earth Science Technology Office of NASA. The QWIP array was fabricated by graded molecular beam epitaxial (MBE) growth that was specifically tailored to yield four distinct bands (FWHM): Band 1; 4.5–5.7 μm, Band 2; 8.5–10 μm, Band 3; 10–12 μm and Band 4; 13.3–14.8 μm. Each band occupies a swath that comprises 128 × 640 elements. The addition of the LVE (which is placed directly over the array) further divides the four “broad” bands into 209 separate spectral bands ranging in width from 0.02 μm at 5 μm to 0.05 μm at 15 μm. The detector is cooled by a mechanical cryocooler to 46 K. The camera system is a fully reflective, f/4.2, 3-mirror system with a 21° × 25° field of view. The project goals were: (1) develop the 4 band GaAs QWIP array; (2) develop the LVE and; (3) implement a mechanical cryocooler. This paper will describe the efforts and results of this undertaking with emphasis on the overall system characteristics.     

MBE grown type-II MWIR and LWIR superlattice photodiodes

We report on the status of GaSb/InAs type-II superlattice diodes grown and fabricated at the Jet Propulsion Laboratory designed for infrared absorption 2–5 μm and 8–12 μm bands. Recent LWIR devices have produced detectivities as high as 8 × 10¹⁰ Jones with a differential resistance–area product greater than 6 Ohm cm² at 80 K with a long wavelength cutoff of approximately 12 μm. The measured internal quantum efficiency of these front-side illuminated devices is close to 30% in the 10–11 μm range. MWIR devices have produced detectivities as high as 8 × 10¹³ Jones with a differential resistance–area product greater than 3 × 10⁷ Ohm cm² at 80 K with a long wavelength cutoff of approximately 3.7 μm. The measured internal quantum efficiency of these front-side illuminated MWIR devices is close to 40% in the 2–3 μm range at low temperature and increases to over 60% near room temperature.     

640 × 512 pixel narrow-band, four-band, and broad-band quantum well infrared photodetector focal plane arrays

A 9 μm cutoff 640 × 512 pixel hand-held quantum well infrared photodetector (QWIP) camera has been demonstrated with excellent imagery. A noise equivalent differential temperature (NEDT) of 10.6 mK is expected at a 65 K operating temperature with f/2 optics at a 300 K background. This focal plane array has shown background limited performance at a 72 K operating temperature with the same optics and background conditions. In this paper, we discuss the development of this very sensitive long-wavelength infrared camera based on a GaAs/AlGaAs QWIP focal plane array and its performance in quantum efficiency, NEDT, uniformity, and operability. In the second section of this paper, we discuss the first demonstration of a monolithic spatially separated four-band 640 × 512 pixel QWIP focal plane array and its performance. The four spectral bands cover 4–5.5, 8.5–10, 10–12, and 13.5–15 μm spectral regions with 640 × 128 pixels in each band. In the last section, we discuss the array performance of a 640 × 512 pixel broad-band (10–16 μm full-width at half-maximum) QWIP focal plane.     

Analytical modeling of loss characteristics of a polymer arrayed waveguide grating multiplexer

Theoretical analysis is performed for the loss characteristics of a polymer arrayed waveguide grating (AWG) multiplexer around the central wavelength of 1.55 μm with the wavelength spacing of 1.6 nm. The total loss of the device includes the diffraction loss in the input and output (I/O) slab waveguides, bent loss caused by the AWG and I/O channels, leakage loss resulted from the high refractive index substrate, and propagation loss due to the absorption and scattering of the materials of the device. The effects of some structural parameters on the loss characteristics are investigated and discussed. The computed results show that when we select the core thickness as 4 μm, core width as 6 μm, pitch of adjacent waveguides as 15.5 μm, diffraction order as 50, the number of the arrayed waveguides as 91, that of the I/O channels as 17, confined layer thickness between the core and the substrate as 10 μm, distance between the focal point and the origin as 5500 μm, and central angle between the central waveguide and the x-axis (i.e. the vertical of the symmetrical line of the device) as 60°, the total loss of the device can be dropped to the range 3.79–7.93 dB.     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

Increased surface roughness by oxygen plasma treatment of graphite/polymer composite

The technology of selective plasma etching was applied to increase the surface roughness of graphite/polymer composite. Etching was performed with a low pressure weakly ionised oxygen plasma created with a RF generator of the output power of 200 W and frequency of 27.12 MHz. The density of charged particles, density of neutral oxygen atoms and the electron temperature was about 1×10¹⁶ m⁻³, 4×10²¹ m⁻³, and 5 eV, respectively. The effects of plasma treatment were observed by scanning electron microscope (SEM), electron microprobe (EMPA) and Talysurf. It was found that the surface roughness was increased by approximately 15 times, from a virgin sample at the roughness of R_a=0.27 μm to a very rough surface with R_a=4 μm. The roughness increased with increasing plasma exposure time. The EMPA results showed that the amount of sulphur in the surface layer decreased with increasing etching time indicating that PPS polymer was the material etched preferentially.     

Domain wall pinning in polycrystalline perovskite La0.7Sr0.3MnO3

Reversible and irreversible domain wall (DW) motions have been investigated in La_0.7Sr_0.3MnO₃ ceramic samples using frequency-response complex permeability with various amplitudes of AC field. We also examine the effects of temperature in the range from 293 to 368 K and transverse DC magnetic field with a maximum of 4.40×10⁵ A/m on the real part of permeability (μ′). Two relaxations corresponding to reversible wall motions and domain rotations occur in low and high frequency regions, respectively. The irreversible DW displacements can be activated as the amplitude larger than the pinning field of 3 A/m, leading to an increase in μ′. The μ′ obeys a Rayleigh law at the temperature below 343 K or under DC field of less than 4.22×10⁴ A/m. The Rayleigh constant η increases from 5.45×10⁻² to 1.54×10⁻¹ (A/m)⁻¹ as the temperature rises from 293 to 343 K, and η decreases from 5.58×10⁻² to 3.67×10⁻² (A/m)⁻¹ with increasing DC field from 1.99×10³ to 4.22×10⁴ A/m.     

Near-infrared sources in the 1–1.3 μm region by efficient stimulated Raman emission in glass fibers

Low-loss glass fiber waveguides are found to be excellent media for Raman lasers and amplifiers in the near-infrared region of the spectrum. Multiwavelength emission in the 1–1.3 μm range is readily obtained by efficient stimulated Raman scattering in single-mode silica fibers. With a 1.064 μm pulsed pump of 250 W in a 175-m, 6-μm diameter single-mode silica fiber we observed four orders of Stokes radiation at 1.12 μm, 1.18 μm, 1.23 μm and 1.3 μm, respectively. Our results imply that pulsed tunable stimulated Raman emission in this wavelength region is possible using kW tunable infrared dye lasers near 1 μm as pumps. These sources are useful for studying the dispersion of glass fibers as well as for other spectroscopic applications.     

Evaluation of optical loss minima in thallium halide crystals

Fundamental optical losses in the highly transparent region for thallium halide KRS-6 and KRS-5 crystals were evaluated. The projected loss minima are 12 × 10^--⁴ dB/ km at 7.9 μm for KRS-6 and 7 × 10^--⁴ dB/km at 12.9 μm for KRS-5 crystals. The material dispersion becomes zero near 5.05 μm for KRS-6 and near 6.62 μm for KRS-5 crystals.     

Uncooled microbolometer detector: Recent developments at Ulis

Uncooled infrared focal plane arrays are being developed for a wide range of thermal imaging applications. Therefore, to answer these markets, a 35 μm pixel-pitch uncooled IR detector technology has been developed enabling high performance 160 × 120 and 384 × 288 arrays production. Besides a wide-band version from uncooled 320 × 240/45 μm array has been also developed in order to address process control and more precisely industrial furnaces control. The ULIS amorphous silicon technology is well adapted to manufacture low cost detector in mass production. After some brief microbolometer technological background, we present the characterization of 35 μm pixel-pitch detector as well as the wide-band 320 × 240 infrared focal plane arrays with a pixel pitch of 45 μm. Information on the new 640 × 480 array with a pixel pitch of 25 μm is also presented.     

Picosecond nonlinear optical response of Ba0.5Sr0.5TiO3 thin films fabricated by pulsed laser deposition

Well-crystallized Ba_0.5Sr_0.5TiO₃ thin films with good surface morphology were prepared on MgO(1 0 0) substrates by pulsed laser deposition technique at a deposition temperature of 800 °C under the oxygen pressure of 2 × 10⁻³ Pa. X-ray diffraction and atomic force microscopy were used to characterize the films. The full width at half maximum of the (0 0 2) Ba_0.5Sr_0.5TiO₃ rocking curve and the root-mean-square surface roughness within the 5 μm × 5 μm area were 0.542° and 0.555 nm, respectively. The nonlinear optical properties of the films were determined by a single beam Z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that Ba_0.5Sr_0.5TiO₃ thin films exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 5.04 × 10⁻⁶ cm²/kW and β = 3.59 × 10⁻⁶ (m/W), respectively.     

Corrosion monitoring of stainless steel 304L in lithium bromide aqueous solution using transmittance optical detection technique

We report a method based on the power ratio of transmittance for monitoring the corrosion rate in stainless steel 304L immersed in an aqueous solution of lithium bromide at 50 wt%, at 70 °C. The optical transmittance measured in the solution contaminated with corrosion oxides at different times of exposure is related to the physical degradation of the stainless steel samples. Lasers at 532 and 632 nm were utilized for monitoring the accumulation of corrosion oxides dissolved in the lithium bromide solution of the metallic samples for 480 h. The change in the optical power of transmittance was 13 μW/480 h measured at 532 nm and 3.6 μW/480 h at 632 nm. The variation of the power ratio for 532 nm was from 0.01 to 0.24, and for 632 nm, from 0.01×10⁻³ to 15.61×10⁻³; this is proportional to an accumulated corrosion rate of [0.0142×10⁻³–0.552×10⁻³ g/cm²] for an exposure time of 432 h.     

Development of a 1K × 1K, 8–12 μm QWIP array

In the on-going evolution of GaAs quantum well infrared photodetectors (QWIPs) we have developed a 1,024 × 1,024 (1K × 1K), 8–12  μm infrared focal plane array (FPA). This 1 megapixel detector array is a hybrid using an L3/Cincinnati Electronics silicon readout integrated circuit (ROIC) bump bonded to a GaAs QWIP array fabricated jointly by engineers at the Goddard Space Flight Center (GSFC) and the Army Research Laboratory (ARL). We have integrated the 1K × 1K array into an SE-IR based imaging camera system and performed tests over the 50–80 K temperature range achieving BLIP performance at an operating temperature of 57 K. The GaAs array is relatively easy to fabricate once the superlattice structure of the quantum wells has been defined and grown. The overall arrays costs are currently dominated by the costs associated with the silicon readout since the GaAs array fabrication is based on high yield, well-established GaAs processing capabilities. One of the advantages of GaAs QWIP technology is the ability to fabricate arrays in a fashion similar to and compatible with silicon IC technology. The designer’s ability to easily select the spectral response of the material from 3 μm to beyond 15 μm is the result of the success of band-gap engineering and the Army Research Lab is a leader in this area. In this paper we will present the first results of our 1K × 1K QWIP array development including fabrication methodology, test data and imaging capabilities.     

Surface electromigration of metals on Si(001): In/Si(001)

The possibility of surface electromigration (SE) of metals of In, Ga, Sb and Ag on a very flat Si(001)2×1 substrate (single domain 2×1) was examined by SEM, μ-RHEED and μ-AES under UHV conditions. It was found that Ga, Sb and Ag show no SE on Si(001) surface even at DC annealing temperatures for the desorption of these metals. For In on Si(001), a very fast SE (8000 μm/min) towards the cathode side was found that suddenly sets in at 450°C DC annealing, which was related to a surface phase transition. μ-RHEED and μ-AES observation showed that the SE is related to an ordered 4×3-In phase together with two-dimensional In gas phase over the 4×3-In phase and an In-disordered phase at the front end of SE. Single domain 4×3-In phases were found to occur under sequences of In deposition and DC annealing which involve the In SE on Si(001).     

Propagating beam analysis of fiber wavelength filters with a depressed-index section

A wavelength filter consisting of single-mode and few-mode fibers is investigated numerically. A simple finite-difference beam-propagation method, in which a transparent boundary condition can be imposed, is developed for circularly symmetric waveguides. After confirming the validity of the numerical method by the mode-mismatch loss, we calculate the propagating field in the fiber wavelength filter, in which interference between LP₀₁, and LP₀₂ modes occurs. To improve the filtering operation, a depressed-index fiber is employed for the few-mode fiber. The effects of the radius and refractive index of the depressed section on the transmission power are revealed and discussed. Power is suppressed to less than 0.1% at 1.3 μm, while maintaining power transmission of more than 85% at 1.55 μm. It is also found that the filtering operation shifts to higher wavelengths as the input power is increased when we choose a self-focusing nonlinear material in the depressed section.     

Si doped GaAs/AlGaAs terahertz detector and phonon effect on the responsivity

Terahertz detection capability of an n-type heterojunction interfacial work function internal photoemission (HEIWIP) detector is demonstrated. Threshold frequency, f₀, of 3.2 THz (93 μm) was obtained by using n-type GaAs emitter doped to 1 × 10¹⁸ cm⁻³ and Al_0.04Ga_0.96As single barrier structure. The detector shows a broad spectral response from 30 to 3.2 THz (10–93 μm) with peak responsivity of 6.5 A/W at 7.1 THz under a forward bias field of 0.7 kV/cm at 6 K. The peak quantum efficiency and peak detectivity are 19% and 5.5 × 10⁸ Jones, respectively under a bias field of 0.7 kV/cm at 6 K. In addition, the detector can be operated up to 25 K.     

On cobalt magnetization suppression at bimetallic interfaces

We study theoretically the Co magnetization suppression at the Co–M (M=Ti, Nb, Mo, Re, Os, Ir and Pt) interface. We consider (1) M(1×1) overlayer on the FCC(1 1 1) or HCP(0 0 0 1) slab, (2) c(2×2) Co–M alloy above the same surfaces. In the latter case, the Co magnetization is reduced to about 0.5 μ_B by Ti, Nb, Mo and Re, but the effect is probably an overestimation because of compression of M–Co bonds. At Co atoms below the M(1×1) overlayer, the Co magnetization does not drop below 1 μ_B. We discuss also the Co–M antiferromagnetic coupling.     

EXAFS analysis of Er sites in Er–O and Er–F co-doped crystalline Si

We present extended X-ray absorption fine structure (EXAFS) and photoluminescence (PL) analyses of Er–O and Er–F co-doped Si. Samples were prepared by multiple implants at 77 K of Er and co-dopant (O or F) ions resulting in the formation of a2 μm thick amorphous layer uniformly doped with 1×10¹⁹ Er/cm³ and 3×10¹⁹ O/cm³, 1×10²⁰ O/cm³ or 1×10²⁰ F/cm³. EXAFS measurements show that the local environment of the Er sites in the amorphous layers consists of 6 Si first neighbors. After epitaxial regrowth at 620°C for 3 h, Er is fully coordinated with 8 F ions in the Er–F samples, while Si and O ions are concomitantly present in the first shell of O co-doped samples. Post regrowth thermal treatments at 900°C leave the coordination unchanged in the Er+F, while the Er+O (ratio 1 : 10) doped samples present Er sites with a fully O coordinated shell with an average of 5 O atoms and 4 O atoms after 30 s and 12 h, respectively. We have also found that the fine structure and intensity of the high-resolution PL spectra are strongly dependent on the Er-impurity ratio and on thermal process parameters in the Er–O co-doped samples, while this is not observed for the F-doped samples. The most intense PL response at 15 K was obtained for the 1 : 3 E : O ratio, suggesting that an incomplete O shell around Er is particularly suitable for optical excitation.     

InAs/GaAs quantum dot infrared photodetectors with different growth temperatures

InAs/GaAs quantum dot infrared photodetectors were fabricated with quantum dots grown at three different temperatures. Large detection wavelength shift (5–14.5 μm) was demonstrated by changing 40 degrees of the epitaxy temperature. The smaller quantum dots grown at lower temperature generate 14.5 μm responses. The detectivity of the normal incident 15 μm QDIP at 77 K is 3 × 10⁸ cm Hz^1/2/W. A three-color detector was also demonstrated with quantum dots grown at medium temperature. The three-color detection comes from two groups of different sizes of dots within one QD layer. This new type of multicolor detector shows unique temperature tuning behavior that was never reported before.     

Photonic crystal waveguide directional couplers as wavelength selective optical filters

Waveguide directional couplers, formed by two closely spaced linear defect waveguides in a two-dimensional photonic crystal of air holes in a semiconductor matrix, are numerically studied using plane wave expansion and finite difference time domain methods. The coupling lengths are on a wavelength scale and show a strong wavelength dependence, allowing for the design of compact wavelength selective optical filters. Applications as a channel interleaver for the 1.55 μm wavelength range and as a micrometer sized 1.31/1.55 μm wavelength demultiplexer are presented.