磺化苯膦酸-磷酸锆的制备及其对甲醛羰基化反应的催化性能

合成了苯膦酸锆及其混合配体形式的苯膦酸.磷酸锆和苯膦酸-亚磷酸锆,并通过层间苯环磺化制备了不同组成的磺化苯膦酸-磷酸锆(SZrPP-n).利用电感耦合等离子体、X射线衍射、热重、红外光谱等手段对样品磺化前后的结构和性质进行了表征,考察了SZrPP-n对甲醛羰基化反应的催化性能.结果表明.苯膦酸.磷酸锆具有典型的层状结构,改变合成条件可以得到层间距不同的晶体.磺化后,SZrPP-n样品层间距增大,具有丰富的酸性位,热稳定性可以达到200℃以上.SZrPP-n对甲醛羰基化制乙醇酸甲酯反应具有较高的催化活性和稳定性.     

层状苯膦酸-磷酸锆的合成与磺化研究

研究了制备苯膦酸-磷酸锆Zr(PO₄H)_2-n(PO₃Ph)_n的主要影响因素。在F^-/Zr⁴⁺=12和H₃PO₄/Zr⁴⁺=20条件下,通过改变苯膦酸用量获得了n=0～2的系列单一晶相层状苯膦酸-磷酸锆,其热稳定性达400℃以上。苯膦酸-磷酸锆的磺化试验表明层间苯环可被完全磺化,磺化产物Zr(PO₄H)_2-n(PO₃PhSO₃H)_n具有丰富的酸性位,其热稳定性亦可达到300℃以上。     

氧化铬层柱苯膦酸锆的合成与选择氧化性能

采用乙胺预胶体化方法合成了一系列氧化铬层柱苯膦酸锆和氧化铬层柱磷酸锆催化剂,其铬含量达到22.5%-36.5%,比表面为316-462m^2/g,中孔孔容占总孔容的70%以上,孔径集中在2nm左右。氧化铬层柱苯膦酸锆的热稳定性较高。以30%H~2O~2为氧化剂时,这类催化剂对苯、甲苯、乙苯、环己烷、环己烯、正庚烷和正丁醇等有机化合物具有比CrAPO-11和CrMCM-41更高的选择氧化活性。     

磺化苯膦酸锆的制备及其催化酯化反应研究

以苯和三氯化磷等小分子化合物为原料,合成制备了固体酸催化剂磺化苯膦酸锆,用红外光谱、Ｘ－射线衍射方法对其结构表征,并研究其在酯化应中的催化活性。实验结果表明：磺化苯膦酸锆是一种具有层状结构的活性较高的固体酸催化剂,乙酸丁酯,氯乙酸丁酯反应温度控制在１１０～１２０℃,产物收率在８０％以上,催化剂重复使用多次后用稀酸浸泡可恢复活性。     

晶态层状(甘氨酸-N，N-双亚甲基膦酸-磷酸氢)锆的制备和插层

晶态层状(甘氨酸-N;N-双亚甲基膦酸-磷酸氢)锆的制备和插层;（甘氨酸-N;N-双亚甲基膦酸-磷酸氢）锆; 正丁胺; 插层     

顺式二胺基二苯并-18-冠-6插层α-磷酸锆复合材料的制备及对锶吸附性能的研究

使用直接插层法制备了顺式二胺基二苯并18-冠-6(cis-DAmDB18C6)插层α-磷酸锆(α-ZrP)材料,通过静态吸附实验,对比了顺式二胺基二苯并18-冠-6插层磷酸锆材料和α-磷酸锆对Sr~(2+)的吸附性能。实验结果表明,二胺基二苯并-18-冠-6插层磷酸锆材料对Sr~(2+)的吸附平衡时间约48h,中性溶液高温有利于吸附,低温高酸有利于解吸,最大吸附容量为125mg·g~(-1),这种插层材料对Sr~(2+)的吸附能力优于α-磷酸锆。     

基于原位结晶苯膦酸锆膜的油水分离网的制备及应用

运用水热法在铜网表面原位结晶生长苯膦酸锆,获得微纳米级粗糙结构,且苯环排列在苯膦酸锆表面的最外层,使铜网具有超疏水和超亲油的性质,无需任何低表面能物质修饰,即可对油水混合物进行分离.苯膦酸锆层与基底存在一定的结合力,具有机械稳定性;同时又具有抗酸碱的化学稳定性.这种油水分离网不仅能够实现油水混合物的分离,还可以实现乳化油的油水分离,在实际生产运用过程中具有较好的应用前景.     

磺化甲苯膦酸锆的制备及催化反应研究

首次制得磺化甲苯膦酸锆（ＺＳＴＰ），用Ｘ－衍射、热重量分析、红外光谱、元素分析等进行了表征。并以磺化甲苯膦酸锆为固体酸催化剂对酯化、缩醛、缩酮、醇脱水成醚、成烯等有机反应进行了研究。ＺＳＴＰ催化的反应收率高，操作简便，后处理容易，催化剂可以重复使用和再生。     

N,N-二甲基胺乙基膦酸-磷酸氢锆为载体的新型固体碱研究

催化;缩合反应;N;N-二甲基胺乙基膦酸-磷酸氢锆为载体的新型固体碱研究     

硅铝柱撑磷酸锆的合成及在大豆油甲酯环氧化反应中的催化性能

基于模板剂导向组装的方法制备了硅铝柱撑磷酸锆.对材料结构进行了表征,分析了硅铝柱撑结构的形成机制.结果表明,材料中铝分别以四面体与八面体的形式嵌入在柱撑结构的内部和层板表面.通过大豆油甲酯的环氧化反应考察了所得硅铝柱撑磷酸锆的催化性能,其催化选择性可达91.7%.反应历程的分析结果表明良好的层板柱撑结构使大分子的反应物能与层间活性位充分接触.硅铝柱撑磷酸锆的酸位特点及催化反应的动力学分析表明,铝源的引入提高了柱撑材料的Lewis酸含量,改善了柱撑磷酸锆对大豆油甲酯环氧化的催化性能.     

Effects of polyacrylic acid on the room-temperature phosphorescence of selected compounds

Polyacrylic acid solutions of 4-phenylphenol, p-aminobenzoic acid, 1,2-benzocarbazole, and 5,6-benzoquinoline were spotted on filter paper and the results obtained by room-temperature phosphorescence were compared with similar samples spotted on filter paper without polyacrylic acid. Improvements in sensitivity ranged from 26 times to 1.1 times and limits of detection from 100 times to 1.1 times for the samples on filter paper with polyacrylic acid. The relative standard deviations for the samples with polyacrylic acid added were also improved.     

近红外光谱快速分析青贮饲料pH值和发酵产物

采用近红外光谱技术,结合偏最小二乘回归法,研究了142个不同种类的秸秆青贮饲料样品的pH值和发酵产物(乳酸、乙酸、丙酸、丁酸和氨态氮),建立了干燥粉碎和新鲜样品的近红外漫反射光谱定量分析模型以及浸提液样品的近红外透射光谱定量分析模型。研究发现,pH值的近红外漫反射光谱和透射光谱的分析效果均较好,校正模型决定系数R2和验证集样品预测值与化学值的相关关系决定系数r2都大于0.80,并且干燥粉碎、新鲜和浸提液样品的RPD值分别为3.44、2.50和2.27;3种状态样品的乳酸、乙酸、丁酸和氨态氮的定量分析模型精度需进一步提高;R2在0.64~0.85之间;RPD值在1.38~1.93之间;丙酸含量的测定结果较差。方差分析显示,3种状态样品的测定结果之间均无显著性差异(P>0.05)。     

在线热辅助甲基化-气相色谱法分析棉籽仁中的脂肪酸组成

建立了分析棉籽仁中脂肪酸组成的在线热辅助甲基化-气相色谱法。将0.3 mg棉籽仁样品与2 μ L三甲基氢氧化硫（0.2 mol/L）加入裂解器,在350℃下进行甲基化反应,通过气相色谱仪进行分离分析,共检测到8种脂肪酸甲酯成分,分别为亚油酸（C18：2）、油酸（C18：1）、棕榈酸（C16：0）、硬脂酸（C18：0）、肉豆蔻酸（C14：0）、棕榈油酸（C16：1）、花生酸（C20：0）和二十二酸（C22：0）,不饱和脂肪酸的相对含量为66.30%~72.54%,其中亚油酸的相对含量为43.20%~53.61%,相对峰面积的相对标准偏差（RSD）小于10%（n=5）。通过分析5组棉籽仁样品与3种食用油中的脂肪酸组成,结果表明不同产地的棉籽仁中的脂肪酸组成差异不明显,且棉籽仁中的脂肪酸组成与玉米油最为接近,相似度为0.960~0.992。该方法简单、快速、准确,适合分析棉籽仁中的脂肪酸组成。     

Fluorimetric determination of phytic acid based on the activation of the oxidation of 2,2'-dipyridyl ketone hydrazone catalysed by Cu(II)

Phytic acid exerts an activation effect on the oxidation of 2,2'-dipyridyl ketone hydrazone catalysed by Cu(II) ion and the oxidation product is highly fluorescent. A fixed time method for the fluorimetric determination of phytic acid based on this effect is described. The calibration graph is linear over the range 0.05-0.6 mg l-1 phytic acid, resulting in a limit of detection of 0.03 mg l-1 phytic acid. The relative standard deviation is in the range 1.4-1.8%, depending on the sample analysed. The method was successfully applied to the determination of phytic acid in human urine (20 samples) and food samples (nine different products). The results obtained for urine samples ranged from 0.31 to 3.6 mg l-1 phytic acid and for food samples from 3.8 to 22 mg g-1 phytic acid. This is the first procedure to be reported for the determination of phytic acid based on fluorimetric measurements.     

Simultaneous analysis of small organic acids and humic acids using high performance size exclusion chromatography

An accurate and fast method for simultaneous determination of small organic acids and much larger humic acids was developed using high performance size exclusion chromatography. Two small organic acids, i.e. salicylic acid and 2,3‐dihydroxybenzoic acid, and one purified humic acid material were used in this study. Under the experimental conditions, the UV peaks of salicylic acid and 2,3‐dihydroxybenzoic acid were well separated from the peaks of humic acid in the chromatogram. Concentrations of the two small organic acids could be accurately determined from their peak areas. The concentration of humic acid in the mixture could then be derived from mass balance calculations. The measured results agreed well with the nominal concentrations. The detection limits are 0.05 mg/L and 0.01 mg/L for salicylic acid and 2,3‐dihydroxybenzoic acid, respectively. Applicability of the method to natural samples was tested using groundwater, glacier, and river water samples (both original and spiked with salicylic acid and 2,3‐dihydroxybenzoic acid) with a total organic carbon concentration ranging from 2.1 to 179.5 mg C/L. The results obtained are promising, especially for groundwater samples and river water samples with a total organic carbon concentration below 9 mg C/L.     

Density changes accompanying wave propagation in the cerium-catalyzed Belousov-Zhabotinsky reaction

Refractive index measurement using an interferometric imaging system and observation of chemical wave shapes were carried out during chemical wave propagation of a cerium-catalyzed Belousov-Zhabotinsky (BZ) reaction. Densities increased as chemical waves propagated in samples without NaBr, and decreased in samples with NaBr. Concentration changes of malonic acid, bromomalonic acid, and BrO3- were estimated from Raman spectral measurements in a stirred batch BZ reaction, and these also exhibited differences between samples with and without NaBr. It is proposed that a reaction subset yielding low molecular weight carboxylic acids is predominant in samples with NaBr, whereas a pathway leading to dibromoacetic acid or tribromoacetic acid production is the major process in samples without NaBr.     

Characterization and recovery of tartaric acid from wastes of wine and grape juice industries

Tartaric acid is mainly used in food, pharmaceuticals and cosmetics industries. In this study, the waste samples, which contain tartaric acid, from the wastes of wine and grape juice industries were characterized by using TG, DSC, FTIR and XRD techniques. HPLC was used to determine tartaric acid content of samples. The decomposition temperatures of waste samples were found to be relatively higher compared with that of pure tartaric acid. This difference in decomposition temperatures was attributed to the presence of potassium tartrate since high potassium content was detected with ICP-AES.     

Application of pressurized sample preparation methods for the analysis of steels and copper alloys

Pressurized sample preparation devices (High Pressure Asher, Pressurized Microwave Digestion system, compared with a PTFE decomposition vessel) were used to dissolve certified metal alloy samples (steel, copper) for ICP analysis. Based on the results of the analysis it was established that both up-to-date devices can be advantageously applied to quickly and quantitatively dissolve metal alloy samples. To dissolve the samples, two different kinds of acid mixtures (A: nitric and hydrochloric acid; B: nitric and hydrochloric and sulphuric and phosphoric acid) were used. The sample preparation is simpler and less time-consuming than the earlier commonly used methods, sample loss and degree of contamination are also reduced. Steel samples containing tungsten, titanium and niobium (less than 0.5%) can only be analyzed using a mixture of the four acids. By dissolving steel samples in the nitric and hydrochloric acid mixture, the concentration of their most common elements (Cr, Ni, Mn, V, Cu) as well as their S and P content can be determined. Copper alloy samples can be dissolved quickly by the pressurized microwave decomposition device using hydrochloric acid and diluted (1:1) nitric acid.     

碘量法与电重法测定氧化铜矿中酸溶铜的方法比较

试料用含亚硫酸钠的硫酸(10%)溶液浸取,使铜的氧化物矿物选择溶解,过滤后加入溴饱和盐酸掩蔽砷和锑等金属,补加少量硫酸,蒸干后用硫酸溶解,用硫代硫酸钠标准溶液滴定测定氧化铜矿中酸溶铜的含量,此方法快速、稳定、准确。选取14个日常分析的样品进行测定,其结果与电解重量法比对,结果令人满意。     

Influences of acid and heat treatments on the structure and water vapor adsorption property of natural zeolite

Natural zeolite was first acid treated and then heat treated. The influences of acid and heat treatments on the structure and water vapor adsorption property of natural zeolite were investigated. X‐ray photoelectron spectroscopy (XPS), X‐ray diffraction (XRD), thermogravimetric analysis (TG), and Brunauer‐Emmett‐Teller (BET) surface areas were employed to investigate the structure changes of the zeolite samples. Water vapor adsorption property of the samples was investigated in order to determine wettability of the samples. The results showed that nitric acid treatment could remove Al from the structure, decrease relative crystallinity, and significantly increase specific surface area of the zeolite samples. Heat treatment could change or even destroy the structure, effectively remove water molecules from the surface/structure, and decrease the specific surface area of the zeolite samples. Water vapor adsorptions on the acid‐treated zeolite samples were significantly lower than that for the zeolite sample, and the adsorptions further reduced for the heat‐treated zeolite samples. The increase of Si/Al ratio, decreases of silanol groups, and specific surface area of the samples were major reasons related to the reductions of water vapor adsorptions on the zeolite samples.