Polyimide and SU-8 microfluidic devices manufactured by heat-depolymerizable sacrificial material technique

The following paper describes a sacrificial layer method for the manufacturing of microfluidic devices in polyimide and SU-8. The technique uses heat-depolymerizable polycarbonates embedded in polyimide or SU-8 for the generation of microchannels and sealed cavities. The volatile decomposition products originating from thermolysis of the sacrificial material escape out of the embedding material by diffusion through the cover layer. The fabrication process was studied experimentally and theoretically with a focus on the decomposition of the sacrificial materials and their diffusion through the polyimide or SU-8 cover layer. It is demonstrated that the sacrificial material removal process is independent of the actual channel geometry and advances linearly with time unlike conventional sacrificial layer techniques. The fabrication method provides a versatile and fast technique for the manufacturing of microfluidic devices for applications in the field of microTAS and Lab-on-a-Chip.     

Polymer microcantilever biochemical sensors with integrated polymer composites for electrical detection

Micro fabricated sensors based on nanomechanical motion with piezoresistive electrical readout have become a promising biochemical sensing tool. The conventional microcantilever materials are mostly silicon-based. The sensitivity of the sensor depends on Young's modulus of the structural material, thickness of the cantilever as well as on the gauge factor of the piezoresistor. UV patternable polymers such as SU-8 have a very low Young's modulus compared to the silicon-based materials. Polymer cantilevers with a piezoresistive material having a large gauge factor and a lower Young's modulus are therefore highly suited for sensing applications. In this work, a spin coatable and photopatternable mixture of carbon black (CB) and SU-8, with proper dispersion characteristics, has been demonstrated as a piezoresistive thin film for polymer microcantilevers. Results on percolation experiments of SU-8/CB composite and fabrication of piezoresistive SU-8 microcantilevers using this composite are presented. With our controlled dispersion experiments, we could get a uniform piezoresistive thin film of thickness less than 1.2 μm and resistivity of 2.7 Ω cm using 10 wt% of CB in SU-8. The overall thickness of the SU-8/composite/SU-8 is approximately 3 μm. We further present results on the electromechanical characterization and biofunctionalization of the cantilever structures for biochemical sensing applications. These cantilevers show a deflection sensitivity of 0.55 ppm/nm. Since the surface stress sensitivity is 4.1 × 10⁻³ [N/m]⁻¹, these cantilevers can well be used for detection of protein markers for pathological applications.     

Fabrication of enclosed SU-8 tips for electrospray ionization-mass spectrometry

We describe a novel electrospray tip design for MS which is fabricated completely out of SU-8 photoepoxy. A three-layer SU-8 fabrication process provides fully enclosed channels and tips. The tip shape and alignment of all SU-8 layers is done lithographically and is therefore very accurate. Fabrication process enables easy integration of additional fluidic functions on the same chip. Separation channels can be made with exactly the same process. Fluidic inlets are made in SU-8 during the fabrication process and no drilling or other postprocessing is needed. Channels have been fabricated and tested in the size range of 10 microm x 10 microm-50 microm x 200 microm. Mass spectrometric performance of the tips has been demonstrated with both pressure-driven flow and EOF. SU-8 microtips have been shown to produce stable electrospray with EOF in a timescale of tens of minutes. With pressure driven flow stable spray is maintained for hours. Taylor cone was shown to be small in volume and well defined even with the largest channel cross section. The spray was also shown to be well directed with our tip design.     

Fabrication of SU-8 based microchip electrophoresis with integrated electrochemical detection for neurotransmitters

A new SU-8 based microchip capillary electrophoresis (MCE) device has been developed for the first time with integrated electrochemical detection. Embedded electrophoretic microchannels have been fabricated with a multilayer technology based on bonding and releasing steps of stacked SU-8 films. This technology has allowed the monolithic integration in the device of the electrochemical detection system based on platinum electrodes. The fabrication of the chips presented in this work is totally compatible with reel-to-reel techniques, which guarantee a low cost and high reliability production. The influence of relevant experimental variables, such as the separation voltage and detection potential, has been studied on the SU-8 microchip with an attractive analytical performance. Thus, the effective electrical isolation of the end-channel amperometric detector has been also demonstrated. The good performance of the SU-8 device has been proven for separation and detection of the neurotransmitters, dopamine (DA) and epinephrine (EP). High efficiency (30,000-80,000 N/m), excellent precision, good detection limit (450 nM) and resolution (0.90-1.30) has been achieved on the SU-8 microchip. These SU-8 devices have shown a better performance than commercial Topas (thermoplastic olefin polymer of amorphous structure) microchips. The low cost and versatile SU-8 microchip with integrated platinum film electrochemical detector holds great promise for high-volume production of disposable microfluidic analytical devices.     

Fabrication of high-aspect-ratio polymer microstructures and hierarchical textures using carbon nanotube composite master molds

Scalable and cost effective patterning of polymer structures and their surface textures is essential to engineer material properties such as liquid wetting and dry adhesion, and to design artificial biological interfaces. Further, fabrication of high-aspect-ratio microstructures often requires controlled deep-etching methods or high-intensity exposure. We demonstrate that carbon nanotube (CNT) composites can be used as master molds for fabrication of high-aspect-ratio polymer microstructures having anisotropic nanoscale textures. The master molds are made by growth of vertically aligned CNT patterns, capillary densification of the CNTs using organic solvents, and capillary-driven infiltration of the CNT structures with SU-8. The composite master structures are then replicated in SU-8 using standard PDMS transfer molding methods. By this process, we fabricated a library of replicas including vertical micro-pillars, honeycomb lattices with sub-micron wall thickness and aspect ratios exceeding 50:1, and microwells with sloped sidewalls. This process enables batch manufacturing of polymer features that capture complex nanoscale shapes and textures, while requiring only optical lithography and conventional thermal processing.     

电沉积技术制作高聚物微流控芯片模具

利用电沉积技术制作微流控芯片金属模具,方法是:使用新型超厚光刻胶SU8胶作近紫外光刻,并在光刻后的图案上电沉积金属Ni,之后去胶,最终获得金属模具.该法减小了电沉积工作量.采用反向电流预处理基底、并适当增加电铸液的添加剂以及脱模后真空退火,即可明显提高电沉积微结构与基底的结合力.用此金属模具成功热压了PMMA,制成了微流控芯片.     

Hybrid microfluidic cartridge formed by irreversible bonding of SU-8 and PDMS for multi-layer flow applications

SU-8 and polydimethylsiloxane (PDMS) are both transparent materials with properties very convenient for rapid prototyping of microfluidic systems. However, previous efforts of combining these two materials failed due to poor adhesion between them. Herein, we introduce a promising low-temperature technique (< 100 °C) to irreversibly bond two or more structured layers of SU-8 and PDMS to create hybrid stacks. This offers new possibilities in design and fabrication of enclosed three-dimensional microstructures and microchannels with simple soft-lithography techniques. The potential of this method is demonstrated by the fabrication of a new version of our microfluidic sensor cartridge that was reported recently¹.     

Simple photografting method to chemically modify and micropattern the surface of SU-8 photoresist

SU-8 has gained widespread acceptance as a negative photoresist. It is also finding increasing use as a structural material in microanalytical devices. Consequently, methods to tailor the surface properties of SU-8 as well as to micropattern coatings on the surface of SU-8 are needed. The SU-8 photoresist consists of EPON SU-8 resin mixed with the photoacid generator triarylsulfonium hexafluoroantimonate. This photoacid generator can also serve as a photoinitiator generating free radicals when illuminated with UV light. Under the appropriate conditions, sufficient triarylsulfonium hexafluoroantimonate remains within cured SU-8 to act as a source of free radicals and initiate UV-mediated grafting of polymers onto the surface of the SU-8. UV-mediated grafting was used to coat SU-8 surfaces with poly(acrylic acid) and other water-soluble monomers. The SU-8 surface was chemically micropatterned by placing a mask between the UV light and SU-8. The X-Y spatial resolution of micropatterned poly(acrylic acid) on the SU-8 surface was 2 mum. Three applications of these chemically modified SU-8 surfaces were demonstrated. In the first, poly(ethylene glycol) was used to protect the SU-8 from interactions with proteins, yielding a surface resistant to biofouling. In the second demonstration, the SU-8 surface was micropatterned with a cell-resistant layer to guide cellular attachment and growth. In the final application, SU-8 micropallets were encoded with polymer lines. The bar codes were read by either absorbance or fluorescence measurements. Thus, UV-mediated graft polymerization is an efficient and effective method to micropattern coatings onto the surface of SU-8.     

Microstencils for the patterning of nontraditional materials

A microfabrication technique that uses a photolithographically patterned film as a microstencil has been developed. This microstencil has a bilayer structure comprised of parylene and SU-8 films with thicknesses from 4 to 100 microm. The parylene layer enables the microstencil to be mechanically peeled from hydrophilic substrates. Since no chemicals are required to release the microstencil, this technique can be used to pattern chemically and biologically sensitive materials. The amount of material deposited can be automatically controlled by the height of the SU-8 structures or externally controlled by spin coating or other thin film deposition techniques. This patterning method is very versatile and has been used to pattern features as small as 25 by 25 microm on silicon, glass, and polymer substrates. As an initial demonstration, we have patterned wax, cells, proteins, sol, and CYTOP.     

Surface modification of SU-8 for enhanced biofunctionality and nonfouling properties

SU-8 is a chemically amplified, epoxy-based negative photoresist typically used for producing ultrathick resist layers during device manufacturing in the semiconductor industry. As a simple resist, SU-8 has garnered attention as a possible material for a variety of biomedical applications, including tissue engineering, drug delivery, as well as cell-based screening and sensing. However, as a hydrophobic material, the use of SU-8 is limited due to a high degree of nonspecific adsorption of biomolecules, as well as limited cell attachment. In this work, surface chemistry is utilized to modify the SU-8 surface by covalently attaching poly(ethylene glycol) (PEG) to increase biofunctionality and improve its nonfouling properties. Different molecular weights and concentrations of PEG were used to form films of various grafting densities on SU-8 surfaces. X-ray photoelectron spectroscopy (XPS) was used to verify the presence of PEG moieties on the SU-8 surface. High-resolution C1s spectra show that, with an increase in concentration and immobilization time, the grafting density of PEG also increases. Further, a standard overlayer model was used to calculate the thickness of the PEG films formed. The effect of PEG-modified SU-8 was examined in terms of protein adsorption on the surface and fibroblast-surface interactions.     

Thermoplastic elastomers for microfluidics: towards a high-throughput fabrication method of multilayered microfluidic devices

Multilayer soft lithography of polydimethylsiloxane (PDMS) is a well-known method for the fabrication of complex fluidic functions. With advantages and drawbacks, this technique allows fabrication of valves, pumps and micro-mixers. However, the process is inadequate for industrial applications. Here, we report a rapid prototyping technique for the fabrication of multilayer microfluidic devices, using a different and promising class of polymers. Using styrenic thermoplastic elastomers (TPE), we demonstrate a rapid technique for the fabrication and assembly of pneumatically driven valves in a multilayer microfluidic device made completely from thermoplastics. This material solution is transparent, biocompatible and as flexible as PDMS, and has high throughput thermoforming processing characteristics. We established a proof of principle for valving and mixing with three different grades of TPE using an SU-8 master mold. Specific viscoelastic properties of each grade allow us to report enhanced bonding capabilities from room temperature bonding to free pressure thermally assisted bonding. In terms of microfabrication, beyond classically embossing means, we demonstrate a high-throughput thermoforming method, where TPE molding experiments have been carried out without applied pressure and vacuum assistance within an overall cycle time of 180 s. The quality of the obtained thermoplastic systems show robust behavior and an opening/closing frequency of 5 Hz.     

Fabrication and Packaging Technologies of Love-wave-based Microbalance for Fluid Analysis

Quartz crystal microbalance (QCM) based techniques have been developed for years to address various kinds of biochemical analyses in liquid media. An alternative to this approach based on guided acoustic shear waves, the socalled Love wave devices, has been proved to allow for increasing gravimetric sensitivity. However, this approach reveals more complicated to implement as the surface on which reactions are achieved is the same as the one used for electrical connection. As a consequence, a microfluidic set-up must be implemented to prevent unwanted interactions between the corresponding areas (IDTs and propagation path). The main issue when using SAW Sensors for in-liquid biochemical analyses [1-4], especially in a commercial objective, is the development of a reliable and reproducible fluidic system [5] meeting the main following requirements: i) low acoustic leakage. ii) chemically inert to biological samples. iii) reproducible fabrication at the wafer scale level.In the present work we explore the use of the SU-8 epoxy-based photoresist combined with silicon or quartz machined covers for the fabrication of this fluidic circuit. A first structure is fabricated using deep etch lithography, the cover is then glued to the remaining SU-8 structure using a thin glue layer. The packaging system prevents covering the IDTs with liquids and defines the sensing area in the region in-between the IDTs. Once the fabrication achieved, we evaluate the velocity and propagation loss using a network analyzer to measure the influence of the proposed packaging approaches on the principal wave characteristics.     

Influence of master fabrication techniques on the characteristics of embossed microfluidic channels

We describe protocols for the fabrication of microfluidic devices in plastics using a number of different embossing masters. Masters were fabricated by deep reactive ion etching (DRIE) of silicon (100), wet etching of silicon (100) and (110), and SU-8 processing. Structures embossed into a cyclo-olefin polymer were characterized in terms of the quality of pattern transfer as well as of the surface roughness. High quality pattern transfer was achieved with masters containing structures with angled sidewalls. Pattern distortions occurring during de-embossing were minimized by using masters consisting of SU-8 (which has a thermal expansion coefficient close to that of the substrates). Structures embossed with SU-8 masters also exhibited the lowest surface roughness. However, due to structural deformation, the reusability of the masters prepared for this study extended to only five embossing experiments. Masters fabricated on silicon, on the other hand, were more robust, but were subject to breakage during the de-embossing phase of the experiment. The results of this study will guide researchers in choosing master fabrication methods that will provide profile and surface characteristics of embossed microfluidic channels that are advantageous to their specific application.     

Rapid prototyping of poly(methyl methacrylate) microfluidic systems using solvent imprinting and bonding

We have developed a method for rapid prototyping of hard polymer microfluidic systems using solvent imprinting and bonding. We investigated the applicability of patterned SU-8 photoresist on glass as an easily fabricated template for solvent imprinting. Poly(methyl methacrylate) (PMMA) exposed to acetonitrile for 2 min then had an SU-8 template pressed into the surface for 10 min, which provided appropriately imprinted channels and a suitable surface for bonding. After a PMMA cover plate had also been exposed to acetonitrile for 2 min, the imprinted and top PMMA pieces could be bonded together at room temperature with appropriate pressure. The total fabrication time was less than 15 min. Under the optimized fabrication conditions, nearly 30 PMMA chips could be replicated using a single patterned SU-8 master with high chip-to-chip reproducibility. Relative standard deviations were 2.3% and 5.4% for the widths and depths of the replicated channels, respectively. Fluorescently labeled amino acid and peptide mixtures were baseline separated using these PMMA microchips in <15s. Theoretical plate numbers in excess of 5000 were obtained for a approximately 3 cm separation distance, and the migration time relative standard deviation for an amino acid peak was 1.5% for intra-day and 2.2% for inter-day analysis. This new solvent imprinting and bonding approach significantly simplifies the process for fabricating microfluidic structures in hard polymers such as PMMA.     

SDS-CGE of proteins in microchannels made of SU-8 films

This work describes the SDS-CGE of proteins carried out in microchannels made of the negative photoresist EPON SU-8. Embedded electrophoretic microchannels have been fabricated with a multilayer technology based on bonding and releasing steps of stacked SU-8 films. This technology allows the monolithic integration of the electrodes in the device. A high wafer fabrication yield and mass production compatibility guarantees low costs and high reliability. A poly(methyl methacrylate) (PMMA) packaging allows an easy setup and replacement of the device for electrophoresis experiments. In addition, the wire-bonding step is avoided. The electrophoretic mobilities of four proteins have been measured in microchannels filled with polyacrylamide. Different pore sizes have been tested obtaining their Ferguson plots. Finally, a separation of two proteins (20 and 36 kDa) has been carried out confirming that this novel device is suitable for protein separation. A resolution of 2.75 is obtained. This is the first time that this SU-8 microfluidic technology has been validated for SDS-CGE of proteins. This technology offers better separation performance than glass channels, at lower costs and with an easy packaging procedure.     

Ultra rapid prototyping of microfluidic systems using liquid phase photopolymerization

We present a method for the ultra rapid prototyping of microfluidic systems using liquid phase photopolymerization, requiring less than 5 min from design to prototype. Microfluidic device fabrication is demonstrated in a universal plastic or glass cartridge. The method consists of the following steps: introduction of liquid prepolymer into the cartridge, UV exposure through a mask to define the channel geometry, removal of unpolymerized prepolymer, and a final rinse. Rapidly fabricated masters for polydimethylsiloxane micromolding are also demonstrated. The master making process is compared to SU-8 50 photoresist processes. Press-on connectors are developed and demonstrated. All materials used are commercially available and low cost. An extension of these methods (mix and match) is presented that allows for maximal design flexibility and integration with a variety of existing fluidic geometries, components, and processes.     

Photochemical modification and patterning of SU-8 using anthraquinone photolinkers

Bioactive protein patterns and microarrays achieved by selective localization of biomolecules find various applications in biosensors, bio-microelectromechanical systems (bio-MEMS), and in basic protein studies. In this paper we describe simple photochemical methods to fabricate two-dimensional patterns on a Novolac A derivative polymer (SU-8) and, subsequently, their functionalization with biomolecules. Anthraquinone (AQ) derivatives are used to chemically modify and pattern SU-8 surfaces. Features as small as 20 mum are obtained when using uncollimated light. The X-Y spatial resolution of micropatterned AQ molecules is improved to 1.5 mum when a collimated light source is used. This micropatterning process will be important for the functionalization of MEMS-based biosensors. The method saves several processing steps and can be integrated in cleanroom fabrication thus avoiding contamination of the sensor surfaces.     

Fully integrated PDMS/SU-8/quartz microfluidic chip with a novel macroporous poly dimethylsiloxane (PDMS) membrane for isoelectric focusing of proteins using whole-channel imaging detection

A fully integrated polydimethylsiloxane (PDMS)/modified PDMS membrane/SU-8/quartz hybrid chip was developed for protein separation using isoelectric focusing (IEF) mechanism coupled with whole-channel imaging detection (WCID) method. This microfluidic chip integrates three components into one single chip: (i) modified PDMS membranes for separating electrolytes in the reservoirs from the sample in the microchannel and thus reducing pressure disturbance, (ii) SU-8 optical slit to block UV light (below 300?nm) outside the channel aiming to increase detection sensitivity, and (iii) injection and discharge capillaries for continuous operation. Integration of all these components on a single chip is challenging because it requires fabrication techniques for perfect bonding between different materials and is prone to leakage and blockage. This study has addressed all the challenges and presented a fully integrated chip, which is more robust with higher sensitivity than the previously developed IEF chips. This chip was tested by performing protein and pI marker separation. The separation results obtained in this chip were compared with that obtained in commercial cartridges. Side-by-side comparison validated the developed chip and fabrication techniques.     

Effect of exposure dose on the replication fidelity and profile of very high aspect ratio microchannels in SU-8

We are interested in using SU-8 dense gratings with very high aspect ratio microchannels as the master mold for fabrication of child molds needed for replication. For such applications, the sidewall taper angle and mask replication fidelity of SU-8 are very important. Increasing the exposure time was experimentally observed to decrease the width of the microchannel and the sidewall angle of SU-8 bars. A new diffraction-refraction-reflection model was also developed. The calculated microchannel width and sidewall angle at high exposure dose agreed well with the experimentally observed values indicating that reflection at the silicon substrate was significant. The larger than calculated actual microchannel width for low exposure dose was shown to be due to leaching of unreacted SU-8 in the developer. Dense gratings of high aspect ratio SU-8 bars separated by high aspect ratio (19.1) microchannels were also demonstrated.     

High intensity light emitting diode array as an alternative exposure source for the fabrication of electrophoretic microfluidic devices

A commercially available array of light emitting diodes (LEDs), namely a UV Shark series LED high flux array, was evaluated as a light source for photolithographic patterning of SU-8 photoresist for the fabrication of templates suitable to make poly(dimethylsiloxane) (PDMS) microchips for electrophoresis. At a distance of 15 cm from the substrate, a relatively even intensity of 0.76+/-0.05 mW/cm(2) was obtained over an area sufficient for patterning a 10 cm (4 in.) silicon wafer. The exposure source was evaluated using a spiral mask design covering a 10 cm wafer. PDMS replicates of this template made in a 25 microm thick layer of SU-8 3025 showed little variation in width over the surface of the substrate, with a variation of 3.2% RSD (n=36) and a maximum range in widths of 7.8% of the mean channel width. The use of the optional metal reflector available with the LED array provided partial collimation of the light allowing near vertical structures to be produced across the entire wafer, something which was not possible without the reflector. SU-8 masters prepared using the LED array were compared to masters made using an alternative cheap lithographic source, namely a gel crosslinker. The SU-8 features were much narrower with the LED array than the crosslinker due to the multiple light sources in the crosslinker. A PDMS microchip made using a SU-8 template created using the Shark UV LED array was used for the electrophoretic separation of three anionic fluorescent dyes, with efficiencies up to 32,000 plates. Given that the LED array can be purchased and assembled for less than US$ 500, the Shark UV LED array is a promising alternative to more expensive lithographic light sources and will have significant appeal to many researchers wishing to undertake research in microfluidics around the world.