Dependence of intermediated noble metals on the optical and electrical properties of ITO/metal/ITO multilayers

Sn doped In₂O₃ (ITO) single layer and a sandwich structure of ITO/metal/ITO (IMI) multilayer films were deposited on a polycarbonate substrate using radio-frequency and direct-current magnetron sputtering process without substrate heating. The intermediated metal films in the IMI structure were Au and Cu films and the thickness of each layer in the IMI films was kept constant at 50 nm/10 nm/40 nm. In this study, the ITO/Au/ITO films show the lowest resistivity of 5.6 × 10⁻⁵ Ω cm.However the films show the lower optical transmission of 71% at 550 nm than that (81%) of as deposited ITO films. The ITO/Cu/ITO films show an optical transmittance of 54% and electrical resistivity of 1.5 × 10⁻⁴ Ω cm. Only the ITO/Au/ITO films showed the diffraction peaks in the XRD pattern. The figure of merit indicated that the ITO/Au/ITO films performed better in a transparent conducting electrode than in ITO single layer films and ITO/Cu/ITO films.     

Fabrication and characterization of Pt intermediate transparent and conducting ITO/Pt/ITO multilayer films

Platinum intermediate transparent and conducting ITO/metal/ITO (IMI) multilayered films were deposited by RF and DC magnetron sputtering on polycarbonate substrates without intentional substrate heating. Changes in the microstructure and optoelectrical properties of the films were investigated with respect to the thickness of the intermediate Pt layer in the IMI films. The thickness of Pt film was varied from 5 to 20 nm.In XRD measurements, neither ITO single-layer films nor IMI multilayer films showed any characteristic diffraction peaks for In₂O₃ or SnO₂. Only a weak diffraction peak for Pt (1 1 1) was obtained in the XRD spectra. Thus, it can be concluded that the Pt-intermediated films in the IMI films did not affect the crystallinity of the ITO films. However, equivalent resistivity was dependent on the presence and thickness of the Pt-intermediated layer. It decreased as low as 3.3×10⁻⁴ Ω cm for ITO 50 nm/Pt 20 nm/ITO 30 nm films. Optical transmittance was also strongly influenced by the Pt-intermediated layer. As Pt thickness in the IMI films increased, optical transmittance decreased to as low as 30% for ITO 50 nm/Pt 20 nm/ITO 30 nm films.     

Electrical and structural properties of In-doped ZnO films deposited by RF superimposed DC magnetron sputtering system

Zinc-indium-oxide (ZIO) films were deposited on non-alkali glass substrates by RF superimposed DC magnetron sputtering with a ZIO (9.54 wt% In₂O₃ content) high-density, sintered target at room temperature. The electrical, structural and optical properties of the ZIO films deposited with different sputtering parameters were examined. The total power for RF superimposed DC magnetron sputtering was 80 W. The RF power ratio in the total sputtering power was changed from 0 to 100% in steps of 25%. The ZIO films deposited with a 100% RF discharge showed the lowest resistivity, 1.28×10⁻³ Ω cm, due to the higher carrier concentration. The ZIO film deposited at 50% RF power showed a relatively larger grain size and smaller FWHM. XPS suggested an increase in the level of In³⁺ substitution for Zn²⁺ in the ZnO lattice with increasing RF/(DC+RF) due to the low damage process. The average transmittance of all ZIO films in the visible light region was >80%. The increasing RF power portion of the total sputtering power led to a broadening of the optical band gap, which was attributed to the increase in carrier density according to Burstein-Moss shift theory.     

Optimization of parameters for deposition of Ga-doped ZnO films by DC reactive magnetron sputtering using Taguchi method

Ga-doped ZnO (ZnO:Ga) transparent conductive films were deposited on glass substrates by DC reactive magnetron sputtering. Taguchi method was used to find the optimal deposition parameters including oxygen partial pressure, argon partial pressure, substrate temperature, and sputtering power. By employing the analysis of variance, we found that the oxygen and argon partial pressures were the most influencing parameters on the electrical properties of ZnO:Ga films. Under the optimized deposition conditions, the ZnO:Ga films showed acceptable crystal quality, lowest electrical resistivity of 2.61 × 10⁻⁴ Ω cm, and high transmittance of 90% in the visible region.     

Low temperature deposition of transparent conducting ITO/Au/ITO films by reactive magnetron sputtering

Transparent conducting indium tin oxide/Au/indium tin oxide (ITO) multilayered films were deposited on unheated polycarbonate substrates by magnetron sputtering. The thickness of the Au intermediated film varied from 5 to 20 nm. Changes in the microstructure, surface roughness and optoelectrical properties of the ITO/Au/ITO films were investigated with respect to the thickness of the Au intermediated layer. X-ray diffraction measurements of ITO single layer films did not show characteristic diffraction peaks, while ITO/Au/ITO films showed an In₂O₃ (2 2 2) characteristic diffraction peak. The optoelectrical properties of the films were also dependent on the presence and thickness of the Au thin film. The ITO 50 nm/Au 10 nm/ITO 40 nm films had a sheet resistance of 5.6 Ω/□ and an average optical transmittance of 72% in the visible wavelength range of 400-700 nm. Consequently, the crystallinity, which affects the optoelectrical properties of ITO films, can be enhanced with Au intermediated films.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

Effect of substrate temperature on the growth of ITO thin films

Indium tin oxide (ITO) thin films were deposited onto glass substrates by rf magnetron sputtering of ITO target and the influence of substrate temperature on the properties of the films were investigated. The structural characteristics showed a dependence on the oxygen partial pressure during sputtering. Oxygen deficient films showed (4 0 0) plane texturing while oxygen-incorporated films were preferentially oriented in the [1 1 1] direction. ITO films with low resistivity of 2.05 × 10⁻³ Ω cm were deposited at relatively low substrate temperature (150 °C) which shows highest figure of merit of 2.84 × 10⁻³ square/Ω⋅     

Properties of dc magnetron sputtered Cu2O films prepared at different sputtering pressures

The sputtering pressures maintained during the deposition of Cu₂O films, by dc reactive magnetron sputtering, influence the structural, electrical and optical properties. The crystalline orientation mainly depends on the sputtering pressure. The films deposited at a sputtering pressure of 4 Pa showed single-phase Cu₂O films along (1 1 1) direction. The electrical resistivity of the films increased from 1.1 × 10¹ Ω cm to 3.2 × 10³ Ω cm. The transmittance of the films increased from 69% to 88% with the increase of sputtering pressure from 2.5 Pa to 8 Pa.     

Effect of the oxygen flow rate on the structure and the properties of Ag-Cu-O sputtered films deposited using a Ag/Cu target with eutectic composition

Ag-Cu-O films were deposited on glass substrates by reactive sputtering of a composite Ag₆₀Cu₄₀ target in various Ar-O₂ mixtures. The films were characterised by energy dispersive X-ray analysis, X-ray diffraction, UV-visible spectroscopy and using the four point probe method. The structure of the films is strongly dependent on the oxygen flow rate introduced in the deposition chamber. The variation of the oxygen flow rate allows the deposition of the following structures: Ag-Cu-(O) solid solution, nc-Ag + nc-Cu₂O, nc-Ag + nc-(Ag,Cu)₂O and finally X-ray amorphous. UV-visible reflectance measurements confirm the occurrence of metallic silver into the deposited films. The increase of the oxygen flow rate induces a continuous increase of the film oxygen concentration that can be correlated to the evolution of the film reflectance and the film electrical resistivity. Finally, the structural changes vs. the oxygen content are discussed in terms of reactivity of sputtered atoms with oxygen.     

Influence of charged particle bombardment and sputtering parameters on the properties of HfO2 films prepared by dc reactive magnetron sputtering

HfO₂ films prepared on glass substrates by dc reactive magnetron sputtering in an Ar + O₂ atmosphere are investigated. The films are polycrystallized with a pure monoclinic phase, and the crystallization strongly relates to the technology environment. Charged particle bombardment mainly caused by negative oxygen ions during sputtering on the films results in rougher surface morphology and worse crystalline property. Influence of sputtering pressure, substrate temperature and Ar:O₂ flow ratio is studied. The main orientations of the films are (−1 1 1) and (1 1 1). The (−1 1 1) orientation is stable, but (1 1 1) orientation is very sensitive to the sputtering condition, and it can be suppressed effectively by introducing charged particle bombardment, lowing sputtering pressure and increasing oxygen concentration.     

Rapid thermal annealing of ITO films

Tin-doped indium oxide (ITO) films with 200 nm thickness were deposited on glass substrates by DC magnetron sputtering at room temperature. And they were annealed by rapid thermal annealing (RTA) method in vacuum ambient at different temperature for 60 s. The effect of annealing temperature on the structural, electrical and optical properties of ITO films was investigated. As the RTA temperature increases, the resistivity of ITO films decreases dramatically, and the transmittance in the visible region increases obviously. The ITO film annealed at 600 °C by RTA in vacuum shows a resistivity of 1.6 × 10⁻⁴ Ω cm and a transmittance of 92%.     

Effect of ambient gas on structural and optical properties of titanium oxynitride films

Titanium oxynitride films have been deposited on glass substrates by reactive RF magnetron sputtering of titanium target. The influence of oxygen partial pressure in N₂ + Ar and N₂ + He mixtures was examined on structural and optical properties of titanium oxynitride films. The prepared samples were characterized by X-ray diffraction, EDS, surface profilometer, AFM and contact angle measurement system. With increase in oxygen partial pressure, the grain size decreases from ∼70 nm to ∼50 nm in N₂ + Ar mixture, while from ∼60 nm to ∼37 nm in N₂ + He mixture. The thickness calculated from optical transmission data and surface profilometer is in good agreement with each other. The deposited samples are hydrophobic by nature and the contact angle was found to decrease with increase in oxygen partial pressure. Samples prepared in oxygen partial pressure ≥5.5% show transmittance of about 97% in the visible region of the spectrum in both N₂ + Ar and N₂ + He mixtures. The atomic mass of the sputtering gas (Ar and He) significantly affects the primary crystallite size, orientation as well as band gap. We were able to relate the better crystallisation of titanium atoms with low partial pressure of oxygen when films are deposited in helium instead of argon due to Penning ionization.     

离子束增强沉积制备p型氧化锌薄膜及其机理研究

采用离子束增强沉积方法在Si和SiO₂/Si衬底上制备In-N共掺杂ZnO薄膜(INZO)，溅射靶是用ZnO和2 atm% In₂O₃粉体均匀混合并压制而成，在氩离子溅射ZnO靶的同时，氮、氩混合离子束垂直注入沉积的薄膜.实验结果显示INZO薄膜具有(002)的择优取向，并且为p型导电，电阻率最低为0.9Ωcm.薄膜在氮气、氧气气氛下退火，对薄膜的结构和电学特性与成膜和退火条件的关系进行了分析. 关键词： 氧化锌薄膜 p型掺杂 离子束增强沉积     

Effects of hydrogen flux on the properties of Al-doped ZnO films sputtered in Ar + H2 ambient at low temperature

Al-doped ZnO (AZO) transparent conductive thin films were grown by magnetron sputtering with AZO (98 wt.% ZnO, 2 wt.% Al₂O₃) ceramic target in Ar + H₂ ambient at a relatively low temperature of 100 °C. To investigate the dependence of crystalline and properties of as-grown AZO films on the H₂-flux, X-ray diffraction (XRD), X-ray photoemission spectrometer (XPS), Hall and transmittance spectra measurements were employed to analyze the AZO samples deposited with different H₂-flux. The results indicate that H₂-flux has a considerable influence on the transparent conductive properties of AZO films. The resistivity of 4.15 × 10⁻⁴ Ω cm and the average transmittance of more than 94% in the visible range were obtained with the optimal H₂-flux of 1.0 sccm. Such a low temperature growing method present here may be especially useful for some low-melting point photoelectric devices and substrates.     

An extreme change in structural and optical properties of indium oxynitride deposited by reactive gas-timing RF magnetron sputtering

The indium oxynitride (InON) films were achieved by reactive RF magnetron sputtering indium target which has the purity of 99.999% with a novel reactive gas-timing technique. The structural, optical and electrical properties in a series of polycrystalline InON films affected by gas-timing of reactive N₂ and O₂ gases introduced to the chamber were observed. The X-ray photoelectron spectroscopy revealed that the oxygen content in thin films that compounded to indium and nitrogen, which increased from 10% in indium nitride (InN) to 66% in indium oxide (In₂O₃) films. The X-ray diffraction peaks show that the phase of deposited films changes from InN to InON and to In₂O₃ with an increasing oxygen timing. The hexagonal structure of InN films with predominant (0 0 2) and (0 0 4) orientation was observed when pure nitrogen is only used as sputtering gas, while InON and In₂O₃ seem to demonstrate body-center cubic polycrystalline structures depending on gas-timing. The surface morphologies investigated from atomic force microscope of deposited films with varying gas-timing of O₂:N₂ show indifferent. The numerical algorithm method was used to define the optical bandgap of films from transmittance results. The increasing oxygen gas-timing affects extremely to the change of crystallinity phase from InN to InON and to In₂O₃, the increase of optical bandgap from 1.4 to 3.4 eV and the rise of sheet resistance from 15 Ω/□ to insulator.     

Structural, electrical, and optical properties of ZnInO alloy thin films

Indium zinc oxide (IZO) thin films with different percentages of In content (In/[In+Zn]) are synthesized on glass substrates by magnetron sputtering, and the structural, electrical and optical properties of IZO thin films deposited at different In₂O₃ target powers are investigated. IZO thin films grown at different In₂O₃ target sputtering powers show evident morphological variation and different grain sizes. As the In₂O₃ sputtering power rises, the grain size becomes larger and electrical mobility increases. The film grown with an In₂O₃ target power of 100 W displays the highest electrical mobility of 13.5 cm·V^-1·s^-1 and the lowest resistivity of 2.4 × 10^-3 Ω·cm. The average optical transmittance of the IZO thin film in the visible region reaches 80% and the band gap broadens with the increase of In₂O₃ target power, which is attributed to the increase in carrier concentration and is in accordance with Burstein-Moss shift theory.     

Pulsed Nd:YAG laser depositions of ITO and DLC films for OLED applications

Indium-tin oxide (ITO) films deposited on heated and non-heated glass substrates by a pulsed Nd:YAG laser at 355 nm and ∼2.5 J/cm² were used in the fabrication of simple organic light-emitting diodes (OLEDs), ITO/(PVK + Alq₃ + TPD)/Al. The ITO was deposited on heated glass substrates which possessed resistivity as low as ∼3 × 10⁻⁴ Ω cm, optical transmission as high as ∼92% and carrier concentration of about ∼5 × 10²⁰ cm⁻³, were comparable to the commercial ITO. Substrate heating transformed the ITO microstructure from amorphous to polycrystalline, as revealed by the XRD spectrum. While the polycrystalline ITO produced higher OLED brightness, it was still lower than that on the commercial ITO due to surface roughness. A DLC layer of ∼1.5 nm deposited on this ITO at laser fluence of >12.5 J/cm² improved its device brightness by suppressing the surface roughness effect.     

Synthesis and materials properties of transparent conducting In2O3 films prepared by sol-gel-spin coating technique

Transparent conducting indium oxide (In₂O₃) thin films have been prepared on glass substrates by the simple sol-gel-spin coating technique. These films have been characterized by X-ray diffraction, resistivity and Hall effect measurements, optical transmission, scanning electron microscopy and atomic force microscopy for their structural, electrical, optical and morphological properties. The influence of spin parameters, number of coating, process temperature on the quality of In₂O₃ films are studied. In the operating range of deposition, 400-475 °C, all the films showed predominant (2 2 2) orientation. Films deposited at optimum process conditions exhibited a resistivity of 2×10⁻² Ω cm along with the average transmittance of about 80% in the visible spectral range (400-700 nm).     

ITO/Au/ITO multilayer thin films for transparent conducting electrode applications

Transparent and conducting ITO/Au/ITO multilayered films were deposited without intentional substrate heating on polycarbonate (PC) substrate using a magnetron sputtering process. The thickness of ITO, Au and ITO metal films in the multilayered structure was constant at 50, 10 and 40 nm, respectively.Although the substrate temperature was kept constant at 70 °C, ITO/Au/ITO films were polycrystalline with an (1 1 0) X-ray diffraction peak, while single ITO films were amorphous. Surface roughness analysis indicated ITO films had a higher average roughness of 1.76 nm, than the ITO/Au/ITO film roughness of 0.51 nm. The optoelectrical properties of the ITO/Au/ITO films were dependent on the Au thin film, which affected the ITO film crystallinity. ITO/Au/ITO films on PC substrates were developed with a resistivity as low as 5.6 × 10⁻⁵ Ω cm and a high optical transmittance of 71.7%.     

Crystallization and electrical properties of V2O5 thin films prepared by RF sputtering

V₂O₅ thin films were prepared under various conditions by using reactive RF sputtering technique. The microstructure and electrical properties of the films are have been investigated. X-ray diffraction data revealed the films deposited at low O₂/Ar ratio are amorphous. The orthorhombic structure of film improved after post annealing at 873 K. The microstructure parameters (crystallite/domain size and macrostrain) have been evaluated by using a single order Voigt profile method. Using the two-point probe technique, the dark conductivity as a function of the condition parameters such as film thickness, oxygen content and temperature are discussed. It was also found that, the behaviour of ρd versus d was found to fit properly with the Fuchs-Sondheimer relation with the parameters: ρ_o = 2.14 × 10⁷ Ω cm and ?_o = 112 ± 2 nm. At high temperature, the electrical conductivity is dominated by grain boundaries, the values of activation energy and potential barrier height were 0.90 ± 0.02 eV and 0.92 ± 0.02 V, respectively.