应力对石墨烯热输运性质影响的分子动力学模拟

本文建立了低维薄膜材料导热模型,运用非平衡分子动力学模拟的方法,利用lanmmps软件对单层石墨烯纳米带的导热特性进行仿真分析,根据Fourier定律计算热导率,再对石墨烯纳米带的原子施加一定耦合应力场,把应力耦合作用下的石墨烯热导率与正常的石墨烯纳米带进行了对比研究,模拟数据结果表明:在石墨烯纳米带上施加耦合应力时,会导致石墨烯纳米带热导率升高,且随应力增加而增大,模拟范围内热导率升高2.61倍,并且应力方向会对热导率变化产生一定影响,这个研究为纳米尺度上石墨烯相关研究和进一步提升热导率提供了新思路.     

纳米多孔氩薄膜热导率的分子动力学模拟

利用经典的Lennard-Jones势能模型,采用分子动力学模拟方法研究纳米多孔氩薄膜热导率.结果表明,纳米多孔氩薄膜热导率明显小于同温度下纯纳米氩薄膜热导率,并且孔隙率越大热导率减小越多.借助基于并联方法的有效热导率模型,对纳米多孔氩薄膜的热导率随孔隙率的变化进行解释.模拟结果还发现,薄膜内的多孔分布对薄膜的热导率有影响.     

金属纳米颗粒的热导率

本文使用统计模拟方法对金属纳米颗粒的电子平均自由程进行了计算,并考察了纳米颗粒的晶格比热和声子平均群速度,最后应用动力学理论对纳米颗粒的电子热导率和声子热导率分别进行了求解.研究结果表明:具有相同特征尺寸的方形、球形纳米颗粒的无量纲电子(或声子)平均自由程比较接近.金属纳米颗粒的电子热导率远大于声子热导率;电子、声子热导率随着直径减小呈现降低趋势,而电子热导率的颗粒尺度依赖性比声子热导率更为明显;随着颗粒直径进一步减小,声子热导率与电子热导率趋于同一数量级.当纳米颗粒特征尺寸大于4倍块材电子(或声子)平均自由程,其电子(或声子)热导率的颗粒尺度依赖性将减弱.     

Influence of chirality on the thermal conductivity of single-walled carbon nanotubes

The influence of chirality on the thermal conductivity of single-walled carbon nanotubes(SWNTs) is discussed in this paper, using a non-equilibrium molecular dynamics(NEMD) method. The tube lengths of the SWNTs studied here are 20, 50, and 100 nm, respectively, and at each length the relationship between chiral angle and thermal conductivity of a SWNT is revealed. We find that if the tube length is relatively short, the influence of chirality on the thermal conductivity of a SWNT is more obvious and that a SWNT with a larger chiral angle has a greater thermal conductivity. Moreover, the thermal conductivity of a zigzag SWNT is smaller than that of an armchair one. As the tube length becomes longer, the thermal conductivity increases while the influence of chirality on the thermal conductivity decreases.     

探针法测量低温下生物材料导热系数研究

低温下导热系数测定对生物器官的低温保存很重要。本文用探针法对低温下鱼肉、猪瘦肉、牛肉和脂肪的导热系数进行了测量研究。研究发现肉类生物材料低温下的热导率明显小于冰的热导率,不同肉的热导率不同,从大到小依次是鱼肉、猪瘦肉、牛肉和脂肪,其中脂肪的热导率比其它的小很多。随着温度的下降导热系数反而增大。分析影响生物材料导热系数大小的是水分含量、结构质地和温度。     

考虑界面散射的金属纳米线热导率修正

理论分析了声子和电子输运对Cu, Ag金属纳米线热导率的贡献. 采用镶嵌原子作用势模型描述纳米尺寸下金属原子间的相互作用, 应用平衡分子动力学方法和Green-Kubo函数模拟了金属纳米线的声子热导率; 采用玻尔兹曼输运理论和Wiedemann-Franz定律计算电子热导率; 并通过散射失配模型和Mayadas-Shatzkes模型引入晶界散射的影响. 在此基础上, 考察分析了纳米线尺度和温度的影响. 研究结果表明: Cu, Ag纳米线热导率的变化规律相似; 电子输运对金属纳米线的导热占主导地位, 而声子热导率的贡献也不容忽视; 晶界散射导致热导率减小, 尤其对电子热导率作用显著; 纳米线总热导率随着温度的升高而降低; 随着截面尺寸减小而减小, 但声子热导率所占份额有所增加. 关键词： 纳米线 热导率 表面散射 晶界散射     

固态金属中声子热传递的分子动力学模拟研究

固态金属中的热传递是声子和自由电子共同作用的结果。自由电子引起的热导率可以通过电导率,利用Wiedemann-Franz定律得到,声子引起的热导率目前仍然不能进行实验测量,只能借助其他方法来研究。本文采用非平衡分子动力学(NEMD)方法,用镶嵌原子方法(EAM)势能模型,模拟计算了不同厚度(1.760-10.56nm)金属镍薄膜中由于声子-声子作用引起的热导率。然后根据纳米厚度金属薄膜的热导率借助关联式推到宏观尺度下由于声子-声子作用引起的热导率。结果表明,对于纳米厚度金属薄膜,由于声子-声子作用引起的热导率比块体金属镍的热导率小一个数量级;薄膜厚度越小,声子-声子作用引起的热导率越小;对于块体金属镍,由于声子-声子作用引起的热导率约占其总热导率的33.0%左右。     

氮化硅纳米薄膜非平衡热导率实验研究

3ω实验方法是一种可以对薄膜热导率进行瞬时测量的方法。根据3ω方法测试原理,搭建了薄膜导热系数测试平台,并且分别测试低频率段和高频段薄膜与基底的温升以及薄膜热导率。测试结果表明:Si3N4薄膜的热导率随温度的升高而增大;高频段下,热导率受频率影响大,误差大;在低频段下薄膜热导率与频率变化基本无关;基于电子与声子的局部热平衡运输方程假设,S i3N4薄膜的热导率具有极度非平衡性;通过比较电阻、热导率与温度的关系可以看出加热器的尺寸大小会影响薄膜的热导率,最佳加热器的宽度选用20μm左右。     

水基ZnO纳米流体电导和热导性能研究

利用水热法生成了形状规则、粒径均匀的球形ZnO纳米颗粒, 并超声分散于水中, 制备得到稳定的水基ZnO纳米流体. 实验测量水基ZnO纳米流体在体积分数和温度变化时的电导率, 并测试室温下水基ZnO纳米流体在不同体积分数下的热导率. 实验结果表明, ZnO纳米颗粒的添加较大地提高了基液(纯水)的热导率和电导率, 水基ZnO纳米流体的电导率随纳米颗粒体积分数增加呈非线性增加关系, 而电导率随温度变化呈现出拟线性关系; 纳米流体的热导率与纳米颗粒体积分数增加呈近似线性增加关系. 本文在经典Maxwell热导模型和布朗动力学理论的基础上, 同时考虑了吸附层、团聚体和布朗运动等因素对热导率的影响, 提出了热导率修正模型.将修正模型预测值与实验值对比, 结果表明修正模型可以较为准确地计算出纳米流体的热导率. 关键词： 水热法 电导率 热导率 热导模型     

疏导式结构在头锥热防护中的应用

针对高超声速飞行器工作时头锥恶劣的热环境,为了保证飞行器头锥的尖锐外形, 提出疏导式热防护结构,利用内置高导热碳材料结构为飞行器头锥提供热防护. 采用流固耦合方法对头锥疏导式防热结构进行了分析,验证了头锥内置高导热碳材料具有较好防热效果, 其中来流马赫数(Ma)为9时头锥前缘壁面最高温度下降了21.9%,尾部最低温度升高了15.2%, 实现了热流由高温区向低温区的转移,削弱了头锥的热载荷,强化了头锥的热防护能力. 本文对外蒙皮结构参数、材料参数以及内部高导热碳材料导热率对头锥热防护性能的影响进行了分析, 其中头锥最高温度随着蒙皮材料导热系数的增加而降低到一个稳定值; 随着蒙皮材料表面黑度的增加而降低;随着蒙皮厚度的增加而升高;随着高导热碳材料导热系数的 增加而呈抛物线下降.     

基于量子修正的石墨烯纳米带热导率分子动力学表征方法

本文提出了基于量子修正的非平衡态分子动力学模型,可用于石墨烯纳米带热导率的表征.利用该模型对不同温度下,不同手性及宽度的石墨烯纳米带热导率进行了研究,结果发现:相较于经典分子动力学模型给出的热导率随温度升高而单调下降的结论,在低于Debye温度的情况下,量子修正模型的计算结果出现了反常现象.本文研究还发现,石墨烯纳米带的热导率呈现出明显的边缘效应及尺度效应:锯齿型石墨烯纳米带的热导率明显高于扶手椅型石墨烯纳米带;全温段的热导率及热导率在低温段随温度变化的斜率均随宽度的增加而增大.最后,文章用Boltzmann声子散射理论对低温段的温度效应及尺度效应进行了阐释,其理论分析结果说明文章所建模型适合在全温段范围内对不同宽度和不同手性的热导率进行精确计算,可为石墨烯纳米带在传热散热领域的应用提供理论计算和分析依据.     

Thermal conductivity of micro/nano-porous polymers: Prediction models and applications

Micro/nano-porous polymeric material is considered a unique industrial material due to its extremely low thermal conductivity, low density, and high surface area. Therefore, it is necessary to establish an accurate thermal conductivity prediction model suiting their applicable conditions and provide a theoretical basis for expanding their applications. In this work, the development of the calculation model of equivalent thermal conductivity of micro/nano-porous polymeric materials in recent years is summarized. Firstly, it reviews the process of establishing the overall equivalent thermal conductivity calculation model for micro/nanoporous polymers. Then, the predicted calculation models of thermal conductivity are introduced separately according to the conductive and radiative thermal conductivity models. In addition, the thermal conduction part is divided into the gaseous thermal conductivity model, solid thermal conductivity model and gas–solid coupling model. Finally, it is concluded that, compared with other porous materials, there are few studies on heat transfer of micro/ nanoporous polymers, especially on the particular heat transfer mechanisms such as scale effects at the micro/nanoscale. In particular, the following aspects of porous polymers still need to be further studied: micro scaled thermal radiation, heat transfer characteristics of particular morphologies at the nanoscales, heat transfer mechanism and impact factors of micro/nanoporous polymers. Such studies would provide a more accurate prediction of thermal conductivity and a broader application in energy conversion and storage systems.     

Homotopy perturbation method for fin efficiency of convective straight fins with temperature-dependent thermal conductivity

In this Letter, the homotopy perturbation method (HPM) has been used to evaluate the efficiency of straight fins with temperature-dependent thermal conductivity and to determine the temperature distribution within the fin. The fin efficiency of the straight fins with temperature-dependent thermal conductivity has been obtained as a function of thermo-geometric fin parameter and the thermal conductivity parameter describing the variation of the thermal conductivity. The results reveal that homotopy perturbation method is very effective and simple. The resulting correlation equations can assist thermal design engineers for designing of straight fins with temperature-dependent thermal conductivity.     

Effects of vacancy defects and axial strain on thermal conductivity of silicon nanowires: A reverse nonequilibrium molecular dynamics simulation

Thermal conductivity of silicon nanowires (SiNWs) is evaluated using the reverse nonequilibrium molecular dynamics simulation. The Stillinger–Weber (SW) and Tersoff interatomic potentials are employed to simulate thermal conductivity of SiNWs. In this work, the influence of random vacancy defects, axial strain, temperature and length on thermal conductivity and effective mean free path of SiNWs is investigated. It is found that by raising the percent of random vacancy defects, thermal conductivity of SiNWs decreases linearly for the results obtained form SW potential and nonlinearly for those obtained from Tersoff interatomic potential. Dependence of the thermal conductivity on axial strain is also studied. Results show that thermal conductivity increases as compressive strain increases and decreases as tensile strain increases. Influence of temperature is also predicted. It is found that the thermal conductivity of SiNWs decreases with increasing the mean temperature. Most of the simulations are performed for 4 UC×4 UC×40 UC silicon nanowires using ssp boundary condition.     

基于微结构参数建模的多孔硅绝热层热导率研究

多孔硅由于具有较低的热导率,因而可以将其作为半导体器件中的绝热层.与其他从边界散射等复杂微观热传导机制出发建模研究多孔硅的热导率不同,将多孔硅热导率影响机制更表观地归结到孔洞的存在和分布等结构因素上,把整个多孔硅视为由硅连续材料介质和孔洞连续介质通过串联和并联组合成的复合微结构,给予其低热导率一个更为易于理解和简化的解释.进一步把孔隙率对等效热导率的影响分解为两个不同的部分,即纵向部分和横向部分,半定量地给出不同的孔洞结构和分布下孔隙率与等效热导率的关系.与实验数据进行对比后验证了模型的有效性.继而从结构的角度说明了多孔硅热导率较低的原因.     

Thermal conductivity in near-nodal superconductors

The universal behavior of thermal conductivity at low temperatures is usually taken as the signature of gap nodes in superconductors. Here we show that in near-nodal superconductors the thermal conductivity obeys a two-parameter scaling law, and can develop super-universal behavior if the temperature is about half the gap minimum. However, when the temperature is fixed at about one quarter of the gap minimum, the thermal conductivity can develop a dip versus the scattering rate, which is in excellent agreement with the behavior of the experimental thermal conductivity in Sr2RuO_4. Our theory is useful to correctly analyze the thermal conductivity in any near-nodal superconductor.     

Effects of nano-void density, size and spatial population on thermal conductivity: a case study of GaN crystal

The thermal conductivity of a crystal is sensitive to the presence of surfaces and nanoscale defects. While this opens tremendous opportunities to tailor thermal conductivity, true 'phonon engineering' of nanocrystals for a specific electronic or thermoelectric application can only be achieved when the dependence of thermal conductivity on the defect density, size and spatial population is understood and quantified. Unfortunately, experimental studies of the effects of nanoscale defects are quite challenging. While molecular dynamics simulations are effective in calculating thermal conductivity, the defect density range that can be explored with feasible computing resources is unrealistically high. As a result, previous work has not generated a fully detailed understanding of the dependence of thermal conductivity on nanoscale defects. Using GaN as an example, we have combined a physically motivated analytical model and highly converged large-scale molecular dynamics simulations to study the effects of defects on thermal conductivity. An analytical expression for thermal conductivity as a function of void density, size, and population has been derived and corroborated with the model, simulations, and experiments.     

Phonon thermal transport in InAs nanowires with different size and growth directions

We investigate the phonon thermal transport properties in InAs nanowires with different size and growth directions by using nonequilibrium molecular dynamics methods. The results show a remarkable anisotropy for the thermal conductivity in InAs nanowire. It is found that the thermal conductivity along [110] growth direction is about three times larger than that along [100] or [111] direction. With the increase of temperature, the thermal conductivity along [110] direction decreases significantly. However, the thermal conductivity along other two directions is not sensitive to temperature. Moreover, we find a crossover from ballistic to ballistic-diffusive thermal transport for a certain length of InAs nanowire. A brief physical analysis of these results is given. It is suggested that the anisotropy of thermal conductivity is common for nanowires with zinc blende structures.     

磁场对铁质类金属热导率影响的初步分析

通过使用TC-3型固体热导率测定仪测量外加磁场的铁质类金属圆柱的热导率,并采用控制变量法,从而探究磁场对固体热导率的关系,发现外加磁场与铁质类的金属热导率变化存在线性关系。     

Studying the Temperature Dependence of Thermal Conductivity in a Rock of Combined Composition

A model for the structure of a rock as a heterogeneous system of two components, amorphous and crystalline, is considered. A formula is proposed for calculating the thermal conductivity of rocks with different temperature dependences of the thermal conductivity of their components. When the temperature dependence of the thermal conductivity of the components and their volume fractions is known, the thermal conductivity of the actual rock can be predicted for different combinations of amorphous and crystalline phases.