Effects of output coupler reflectivity on the performance of a linear cavity Brillouin/erbium fiber laser

The effect of output coupler reflectivity (or output coupling ratio) on the performance of a linear cavity Brillouin/erbium fiber laser (BEFL) is demonstrated. The operating wavelength, output laser power and number of channels vary with changes in the coupling ratio in the linear cavity system. The optimum BEFL operation is obtained with an output coupling of 40%, i.e., 60% of the laser power is allowed to oscillate in the cavity. A stable laser comb consisting of up to 40 channels with line spacings of approximately 0.09 nm are obtained at the Brillouin pump and 980 nm pump with powers of 2.5 mW and 100 mW, respectively. The linear cavity BEFL has the potential to be used in inexpensive wavelength division multiplexing system.      

Dual picosecond dye lasers synchronously pumped by a mode locked cw yag laser

The performance of a novel dual dye laser system synchronously pumped by the frequency doubled output of a mode-locked CW-YAG laser is evaluated in relation to pulsewidth, pulse substructure, pulse spectral width and timing jitter. The behavior of the system is adequately described by a theoretical model which includes the time dependent gain and losses due to frequency bandwidth, cavity length mismatch and output coupler. The jitter is significantly reduced from that obtained with CW gas laser pumping as a result of the shorter pump pulse (50 ns instead of ≈100 ps). A routine operating condition uses 2-plate birefringen filters, 0.8 W pump power at 532 nm, to yield two 2.0 ps pulses having a cross correlation width of 3.8 ps, and 30 mW average power from each laser.     

包层泵浦的铒镱共掺光纤激光高效产生的实验研究

利用尾纤输出的977nm高亮度多模半导体激光器包层泵浦铒镱共掺双包层光纤,采用非球面透镜组耦合方式,使泵浦耦合效率达66%以上,并在法布里-珀罗激光振荡腔结构中实现了高效的连续激光产生,双包层光纤长度为2m,在泵浦入纤功率为1.36W时,输出连续功率最大394mW,斜率效率达35%,激光输出波长1.565μm.     

掺铒光纤非线性耦合器的实验研究

提出一种耦合参量可用光调控的掺铒光纤非线性耦合器.用熔融拉锥法熔合两根掺铒光纤,拉制成工作波长为155nm的3dB掺铒光纤耦合器.通过调变输入耦合器一臂的980nm泵浦光功率,可以改变两臂的传播常量差,从而改变耦合器两臂信号光的相对输出功率.通过测量输入泵浦光功率和两臂信号光输出功率,得到直通臂耦合比依赖于泵浦光功率的实验曲线.实验研究表明,当泵浦光功率从0 mW变化至20 mW时,耦合比的变化可达到40％.与理论模拟的结果一致.     

Low-cost low-threshold diode end-pumped Tm:YAG laser at 2.016?μm

We report a low-threshold continuous-wave Tm:YAG laser that can be excited near 785?nm with low-cost, single-mode AlGaAs laser diodes. Low-threshold operation was achieved using a tightly focused, astigmatically compensated x-cavity containing a 2-mm-thick Tm:YAG crystal with 5?% Tm³⁺ concentration. Two linearly polarized single-mode diodes operating at 785.8?nm were polarization coupled to end pump the resonator. With a 6?% output coupler, as high as 32?mW of output power could be obtained at 2016?nm with 184?mW of incident pump power. The output could be further tuned in the 1935?C2035?nm range. Slope efficiency measurements indicated that cross-relaxation was very effective at this doping level. With a 2?% output coupler, lasing could be obtained with as low as 32.3?mW of pump power. In the limit of vanishing output coupling, the incident threshold pump power could be reduced to as low as 25?mW. To our knowledge, this is among the lowest lasing thresholds reported to date for continuous-wave, room-temperature thulium lasers.     

Local-cooled watt-level Nd-doped phosphate single-mode fiber laser

Efficient and stable continuous-wave (CW) laser operation at 1053 nm in a Nd-doped phosphate single-mode fiber (Nd:PSMF) has been demonstrated experimentally. The fiber laser consisted of a 21 cm Nd:PSMF placed in a F-P cavity formed by high reflector butt-coupled to coupling end of the fiber and Fresnel reflection of the other end facet. An output power of 1.42 W and a slope efficiency of 34.1% (18.4%) with respect to absorbed pump power (incident pump power) were obtained with 808 nm diode pumping. An increment as much as 9.7 and 15.0% in slope efficiency of the input coupling efficiency and the output power, respectively, were obtained by using a local-cooling design provided by watered sealing the coupling point. The repeatable results indicate that the design, featuring fluid sealing the coupling point of the fiber laser, which was capable of offering an effective alleviation of thermal effects and an elevation of the quality of the laser cavity, could be expected to be a convenient and effective scheme to improve the performance characteristics of the non-silica fiber lasers and the high power fiber lasers, generally in free-space coupling configuration.     

低阈值掺钛蓝宝石激光器实验研究

结合特殊的谐振腔设计和半导体可饱和吸收镜，建成了一台低阈值的自启动掺钛宝石激光器 . 分别用3％和12％的输出耦合镜，获得了阈值低至390mW和600mW的稳定锁模脉冲输出. 采 用12％输出耦合镜，在12W抽运时，输出平均功率为114mW，对应的典型脉宽为17fs，谱宽 为47nm. 相对于以往的低阈值克尔透镜锁模激光器，锁模工作的范围区域加宽，减小了操作 难度，提高了稳定性. 关键词： 低阈值 半导体可饱和吸收镜 克尔透镜锁模 掺钛蓝宝石激光器     

Broadly tunable continuous-wave diode-pumped Cr4+:YAG laser

We describe a widely tunable, continuous-wave, room temperature Cr⁴⁺:YAG laser with direct pumping by two high brightness 4 W InGaAs laser diodes. In a tunable configuration, the output wavelength covered a span of 197 nm (1356–1553 nm) and provided a maximum power of 195 mW. A maximum non-tunable output power of 260 mW was obtained with a 0.6% transmission output coupler (OC) and 6.6 W of incident pump power. Pumping at two different wavelengths, 911 and 968 nm, was investigated.     

Laser performance of Nd:LaB3O6 cleavage microchips passively Q-switched with a Cr4+:YAG saturable absorber

Passively Q-switched laser oscillation at 1060 nm from an unprocessed Nd:LaB₃O₆ cleavage microchip with a Cr⁴⁺:YAG saturable absorber has been demonstrated. The influence of absorbed pump power, output coupler transmission and cavity length on the output pulse characteristics has been investigated. For a plano-concave cavity with a cavity length of 28 mm, pulse with 100 mW average output power, 4.0 μJ energy, 17 ns duration, 25 kHz repetition rate, and 0.24 kW, peak power was obtained at the absorbed pump power of 1.42 W and output coupler transmission of 3.5%. For a plano-plano cavity with a cavity length of 5 mm, pulse with 85 mW average output power, 2.1 μJ energy, 2.3 ns duration, 40 kHz repetition rate, and 0.89 kW, peak power was obtained at the absorbed pump power of 1.42 W and output coupler transmission of 5.6%. Because a chopper with a 5% duty cycle was employed in the experiments to reduce the influence of pump-induced thermal loading, the above average output powers were obtained at the 5% duty cycle and extrapolated to 100%.PACS 42.55.Rz; 42.60.Gd; 42.70.Hj     

1137 nm长波掺镱光纤激光器的出光实验

分别使用976 nm半导体激光器和1040 nm光纤激光器作为泵浦源,实现了1137 nm长波光纤激光器的出光,输出功率均超过百mW。激光器采用相同的线性腔结构,高反光栅和低反光栅的反射率分别为99.6%和39.7%,增益介质是一段8 m长的掺镱光纤,纤芯直径5 m。当976 nm半导体泵浦功率为912 mW时,1137 nm激光输出功率为182 mW,对应的斜率效率为28.5%;当1040 nm激光功率为1.59 W时,输出的1137 nm激光功率为278 mW,斜率效率约为25%。在此基础上对两种泵浦方式进行了对比分析。     

镱钠共掺氟化钙锁模激光器产生190 fs光脉冲

在半导体激光器高功率抽运的镱、钠共掺氟化钙(Yb, Na:CaF₂)激光器中, 通过对晶体的负热透镜效应的数值模拟,进行激光器腔型的调节和优化,使得该激光器在采用2%的耦合输出镜和吸收抽运功率为7.8 W的条件下,获得了脉冲宽度为190 fs、平均输出功率为503 mW、中心波长为1034 nm、重复频率为82.4 MHz的连续锁模脉冲序列. 如果计算晶体表面反射等其他形式的泄漏输出,激光器的总平均输出功率为905 mW. 关键词： Yb 2晶体')" href="#">Na:CaF₂晶体 激光二极管抽运 飞秒激光     

宽光谱全正色散锁模掺镱光纤激光器

介绍了一种全正色散宽光谱被动锁模掺镱光纤激光器,利用非线性偏振旋转技术实现全正色散掺镱光纤激光器的被动锁模.当泵浦功率输出为500mW时,激光脉冲输出功率大于139mW,重复频率约为28.1MHz,脉冲宽度为3.8ps.为了进一步研究全正色散光纤激光器的宽光谱输出特性,在腔内熔接50m单模光纤,同时去除双折射滤波片,在泵浦功率为500mW时,观察到稳定锁模单脉冲耗散孤子,光谱范围为1 005~1 140nm,输出激光脉冲最大平均功率为90mW,重复频率为3.58MHz,脉冲宽度为519ps.     

新颖的高功率L-波段掺铒光纤超荧光光源

研究了L-波段超荧光在光纤中的产生机理,设计了一种带光纤圈反射器的双级双程前向输出L-波段光源结构,通过对两级采用掺铒浓度不同的光纤并优化其长度及两级泵浦光功率,实验中获得了功率高达19.86mW(12.98dBm)、中心波长为1577.421nm的L-波段(1555-1620nm)超荧光光源。实现了低浓度掺铒光纤起诱导光及改善光谱的作用,高浓度光纤为主要发光源,采用光纤圈反射器提高了泵浦光的利用效率、光源的平坦度及稳定性。同时分析了结构中各个参量对光源各方面性能的影响,对光源的设计具有指导意义。     

同带抽运高效率光纤放大器

以光纤光栅为谐振腔搭建了波长为1020 nm的光纤激光器,并通过两级级联放大获得了590 mW的最大输出功率. 利用获得的波长为1020 nm的激光进行了波长为1064 nm种子光同带抽运放大,实验研究了不同增益光纤长度时放大器的输出功率和转换效率. 当增益光纤长度为8.5 m时,放大器最大输出功率为385 mW,斜率效率为81%. 进行了波长为976 nm的半导体激光器直接抽运波长为1064 nm种子光的实验. 在增益光纤长度最优时,其斜率效率为56.4%. 实验结果表明,同带抽运方式比传统抽运方式具有更高的转换效率. 研究结果可为波长为1020 nm的激光高功率放大和波长为1064 nm的光纤激光高功率同带抽运放大提供一定的参考. 关键词： 同带抽运 光纤放大器 斜率效率     

300 W侧面分布式抽运掺Yb全光纤放大器

采用角度磨抛的方式, 在纤芯/包层为20/400 μm双包层掺Yb光纤上制作了侧面抽运耦合器. 该耦合器对975 nm的半导体二极管抽运光的耦合效率最高可达97%, 对1080 nm信号光的泄漏比小于2%. 分析了侧面抽运耦合器的性能以及多个侧面抽运耦合器的级联分布对抽运耦合效率的影响; 同时, 在前向抽运和双向抽运方式下, 分析了级联耦合器的分布及信号光泄漏比对激光器整体效率的影响, 并进行了数值模拟. 采用自行研制的侧面抽运耦合器, 搭建了侧面耦合分布式抽运、掺Yb双包层全光纤主振荡功率放大器, 获得了波长为1080 nm、功率为303 W 的基模激光输出. 进一步增加抽运点个数, 提高抽运功率, 可获得更高的输出功率.     

A simple linear cavity dual-wavelength fiber laser using AWG as wavelength selective mechanism

In this paper, a simple design of linear cavity dual-wavelength fiber laser (DWFL) is proposed. Operating in the C-band region stretching from 1538.3 nm to 1548.6 nm, an arrayed waveguide grating (AWG) is used to generate the dual-wavelengths output together with a broadband fiber Bragg grating as a back reflector and an optical circulator with a 10% output coupling ratio which acts as a front mirror. The measured average output power of the DWFL is about −5.66 dBm and with a side mode suppression ratio (SMSR) of 53.1 dB. The spacing between the two output wavelengths can be varied from 0.8 nm to 10.3 nm with a stable output and minimum power fluctuations.     

基于类噪声脉冲抽运的平坦超连续谱光源

设计了一种由类噪声脉冲抽运的全光纤结构平坦超连续谱光源。在色散管理掺铒光纤激光器中通过调节腔内偏振态,在泵浦功率为450 mW时,实现了稳定的类噪声脉冲锁模,锁模脉冲的中心波长为1 600 nm,脉冲宽度为303 fs。在最大泵浦功率为1 W时,谐振腔直接输出功率为8.6 mW。较低的功率无法有效拓展超连续谱宽度,为此设计一种掺铒光纤放大器进行功率放大,放大器最大输出功率为338 mW,将功率放大后的类噪声脉冲耦合进高非线性光纤以产生超连续谱,超连续谱的20 dB光谱范围为1 530 nm～2 300 nm,在1 736 nm～2 134 nm范围内,光谱的平坦度优于0.5 dB。     

钛宝石泵浦的Yb:YAG晶体的激光性能

测量了Yb:YAG晶体的光谱特性,用Ar⁺离子泵浦钛宝石激光器作为泵浦源泵浦Yb:YAG晶体,采用平平腔设计,当输出耦合镜T_1.053μm=4.26%,泵浦功率为1410mW时,得到320mW1.053μm的高效CW激光输出,斜率效率为54%,外推阈值功率为203mW。     

高效率599 nm Ba(NO3)2外腔喇曼激光器

橘黄色波段固体激光器在基于荧光探测的生物医学诊断和显示等众多方面有着广泛的实际应用. 报道了利用532 nm的Nd∶YAG倍频激光抽运外置喇曼腔内的硝酸钡晶体,获得高效率的599 nm橘黄色喇曼激光的实验结果.对外置喇曼腔实验装置和运转参量进行了优化,喇曼振荡腔由对二阶斯托克斯光有最优化反射率的腔镜构成,对实验中所得到的二阶斯托克斯喇曼激光脉宽压缩及出现双尖峰的现象进行了分析.当抽运光功率达到4.1 W时,获得二阶斯托克斯喇曼激光功率为710 mW,输出光中心波长为599.38 nm,半峰全宽（FWHM）为1.1 nm,激光器最大光光转换效率为17.5%,斜率效率为24.8%.     

大功率高效率掺铒超荧光光纤光源及其应用

采用光纤反射环镜和双程后向结构,得到了最大输出功率30.6 mW、光光转换效率42.0%的大功率、高效率全光纤掺铒超荧光光源（SFS）.利用串接光纤光栅（FBG）和光纤型F-P腔,对其进行光谱分割,得到了稳定的多波长输出.实验结果和探讨对光谱分割多波长光源的研制具有指导意义.