KGW晶体外腔式高功率579nm喇曼黄光激光器

报道了579nm高功率KGd(WO4)2喇曼晶体外腔式喇曼黄光激光器的输出特性.基于808nm脉冲激光二极管侧面泵浦Nd∶YAG陶瓷、腔内BBO电光晶体同步延迟调Q和Ⅰ类临界相位匹配的LBO晶体腔外倍频方案,并通过外腔式KGW晶体Ng轴二阶斯托克斯喇曼频移,获得了579.54nm黄光激光输出.当脉冲信号重复频率为1kHz、532nm泵浦光最高平均功率为5.02W、脉冲宽度为10.1ns时,获得了最高平均功率2.58 W、脉冲宽度7.4ns、峰值功率348.6kW的579.54nm二阶斯托克斯喇曼黄光激光输出;532nm至579.54nm的光-光转化效率为51.4%、斜率效率为54.8%,光束质量因子Mx2-579.54=5.829、My2-579.54=6.336,输出功率不稳定性小于±2.35%.实验表明:外腔式喇曼结构能够高效地获得喇曼黄光,具有很高的光-光转化效率及良好的功率稳定性,并通过脉冲LD结合同步延迟电光调Q可获得高重复频率、高平均功率、窄脉冲宽度和高峰值功率的黄光激光输出.     

KGW 晶体外腔式高功率579 nm喇曼黄光激光器

报道了579 nm高功率KGd(WO₄)₂喇曼晶体外腔式喇曼黄光激光器的输出特性.基于808 nm脉冲激光二极管侧面泵浦Nd:YAG陶瓷、腔内BBO电光晶体同步延迟调Q和Ⅰ类临界相位匹配的LBO晶体腔外倍频方案,并通过外腔式KGW晶体Ng轴二阶斯托克斯喇曼频移,获得了579.54 nm黄光激光输出.当脉冲信号重复频率为1 kHz、532 nm泵浦光最高平均功率为5.02 W、脉冲宽度为10.1 ns时,获得了最高平均功率2.58 W、脉冲宽度7.4 ns、峰值功率348.6 kW的579.54 nm二阶斯托克斯喇曼黄光激光输出;532 nm至579.54 nm的光-光转化效率为51.4%、斜率效率为54.8%,光束质量因子M_x-579.54²=5.829、M_y-579.54²=6.336,输出功率不稳定性小于±2.35%.实验表明:外腔式喇曼结构能够高效地获得喇曼黄光,具有很高的光-光转化效率及良好的功率稳定性,并通过脉冲LD结合同步延迟电光调Q可获得高重复频率、高平均功率、窄脉冲宽度和高峰值功率的黄光激光输出.     

高效率,窄脉冲1 198.5 nm Ba(NO3)2喇曼激光器

利用1064nm的Nd∶YAG激光抽运振荡腔内的硝酸钡晶体,获得高效率、窄脉冲的喇曼激光输出.硝酸钡晶体由水溶液降温法生长,长度为48 mm.喇曼振荡腔由对抽运光、一阶、二阶斯托克斯光有不同反射率的双色平面镜构成.当抽运光功率达到4.5 W时,获得最高的一阶斯托克斯喇曼激光功率为1.48 W,相应的转换效率为32.9%,并测得斜率效率为40%.由于受激喇曼散射的作用,喇曼脉冲光由抽运脉冲光的19.8 ns压缩为2.4 ns,获得的喇曼激光脉冲波形具有的“上升沿陡峭、下降沿缓慢”的特性,对其形成过程作了定性分析.测得喇曼激光的波长为1 198.5 nm,半峰全宽（FWHM）为1.2 nm.     

LD抽运Nd∶YVO_4自喇曼倍频黄光激光器

报道了LD抽运的自喇曼c切Nd∶YVO4调Q腔内倍频黄光激光器.Nd∶YVO4晶体同时作为激光介质和喇曼晶体,通过声光调Q技术,产生了1178.7nm的喇曼激光,经过KTP腔内倍频,输出589.4nm黄光.测量了平均输出功率随抽运功率和脉冲重复率的变化.典型的1066.7nm基频光、1178.7nm喇曼光和589.4nm倍频光的脉冲宽度分别为24.9ns、11.2ns和6.8ns.在脉冲重复率为15kHz,抽运功率为7.56W时,产生了平均功率为151mW的589.4nm光的输出.     

输出功率稳定的二级喇曼光纤激光器特性

提出一种输出功率稳定的二级喇曼光纤激光器,从理论分析角度探讨了它的特性.结果表明：由于在抽运光的二级斯托克斯光频附近的自发辐射光的钳制作用,激光器的一级和二级输出功率几乎都不受抽运功率波动的影响,从而降低了抽运光低频相对强度噪音转移|激光器输出的一级和二级斯托克斯光功率都很稳定,并且通过调节激光器结构中的可变衰减器,可以有效控制一级、二级激光的输出功率以及它们的比值.这些特性表明该喇曼光纤激光器很适合于作为喇曼光纤放大器的抽运源.     

输出功率稳定的二级喇曼光纤激光器特性

提出一种输出功率稳定的二级喇曼光纤激光器,从理论分析角度探讨了它的特性.结果表明:由于在抽运光的二级斯托克斯光频附近的自发辐射光的钳制作用,激光器的一级和二级输出功率几乎都不受抽运功率波动的影响,从而降低了抽运光低频相对强度噪音转移;激光器输出的一级和二级斯托克斯光功率都很稳定,并且通过调节激光器结构中的可变衰减器,可以有效控制一级、二级激光的输出功率以及它们的比值.这些特性表明该喇曼光纤激光器很适合于作为喇曼光纤放大器的抽运源.     

LDS751染料的受激喇曼散射

报道了用532nm激光抽运LDS751染料产生720—780nm可调谐染料激光输出的同时,观察到喇曼频移为102和45cm-1的反斯托克斯线,前者谱线较强,后者较弱.与这两条强线对应的斯托克斯线未能观察到.另外,还观察到喇曼频移为34cm-1的一级和二级斯托克斯线与反斯托克斯线 关键词： LDS751染料 受激喇曼散射 喇曼位移 斯托克斯线 反斯托克斯线     

级联掺磷光纤喇曼激光器的解析优化

讨论了二级级联喇曼光纤激光器的解析解和优化设计.通过引入几何平均功率、增益因子和归一化光纤有效长度,将描述泵浦光和斯托克斯光沿喇曼增益光纤分布的微分方程组简化成代数方程组,在对泵浦光采用线性传播近似后,获得了二级级联喇曼激光器的解析解.所获得的解析解同数值模拟结果吻合得很好.利用该解析解可方便和快速地讨论级联喇曼激光器的优化设计,计算不同泵浦功率下的最佳光纤长度、输出光纤光栅反射率和转换效率.泵谱功率越大,最佳光纤长度越短,最佳输出光纤光栅反射率越小.     

XeCl激光泵浦高压氢的衍射极限SRS斯托克斯光输出

利用XeCl准分子激光在高压氢中产生受激喇曼散射获得峰值功率为0.2MW、衍射极限发射角的一阶(353nm)斯托克斯输出,井研究了泵浦激光发散角对受激喇曼散射转换效率的影响.     

抽运光谱宽度对喇曼光纤放大器的影响

采用受激喇曼散射（SRS）耦合波理论分析了抽运光谱宽度对喇曼光纤放大器的影响, 指出当采用宽光谱作抽运光时会降低抽运效率. 同时, 文中还给出了抽运光谱宽度、抽运光功率和抽运效率间的变化规律曲线, 得出当传输光纤的有效截面积越小、喇曼增益系数越大、抽运光的入纤功率和光谱线宽度越大时, 光谱抽运效率越小的结论.     

532 nm激光泵浦硝酸钡晶体产生外腔拉曼激光

 由于硝酸钡晶体具有很强的对称振动(频率1 047 cm^-1)和较高的拉曼增益，可以用来产生受激拉曼激光。采用单端泵浦的外置拉曼振荡腔与双棱镜分光装置进行了硝酸钡晶体拉曼激光实验，泵浦源为倍频Nd: YAG的532 nm激光，硝酸钡晶体通过水溶液降温法生长，尺寸为10 mm×10 mm×48 mm，采用特殊镀膜的腔镜对各阶斯托克斯光进行优化选择。在泵浦源达到65 mJ时，获得21 mJ一阶斯托克斯光，输出波长为563 nm，以及16 mJ的二阶斯托克斯光，输出波长为599 nm，受激拉曼散射SRS最大的整体转换效率（包含一阶、二阶斯托克斯光之和）为56.3%。     

Output Characteristics of High-Power Continuous Wave Raman Fiber Laser at 1239 nm Using Phosphosilicate Fiber

A high-power singlemode Raman fiber laser (RFL) with maximum output power of 4.11 W and maximum power conversion efficiency of 47.40% at 1239 nm is realized using continuous wave 8.4 W Yb-doped double-clad fiber laser as a pump, 700 m phosphosilicate fiber, and a Raman cavity formed by a pair of fiber Bragg grating mirrors at 1239 nm. The output characteristics of the RFL at 1239 nm for different fiber lengths and output mirror reflectance are reported. Theoretical simulation is done to numerically optimize for fiber length and output coupler reflectivity to obtain maximum first Stokes power.     

Numerical optimization of the extracavity Raman laser with barium nitrate crystal

The radiation transfer equations of the extracavity Raman laser including up to the third Stokes beams and backward Raman scattering terms were deduced in detail from the wave equation and material equations of stimulated Raman scattering. The radiation transfer equations were solved numerically to optimize the performance of the extracavity Raman lasers with barium nitrate crystal as the nonlinear medium. The optimum reflectivity of the output coupler at the first Stokes was figured out numerically to achieve the maximum conversion efficiency of the first Stokes, and found to be closely related to the pump pulse duration, peak intensity of the pump pulse, and Raman crystal length. With the resonator mirrors highly reflective at the first Stokes, the highest conversion efficiency of the second Stokes was obtained when the input mirror was highly reflective at second Stokes, whereas the output coupler was highly transmissive at the second Stokes. It was found that too high intracavity intensity of the second Stokes would impede the efficient energy extraction from the pump pulse to the first Stokes, and consequently, limit the conversion efficiency of the second Stokes.     

579 nm外腔式拉曼激光器传输耦合方程的数值计算

 为了提高以KGd(WO4)2晶体为拉曼介质的外腔式拉曼激光器的输出功率和转化效率,采用面积求和法编制matlab计算程序,对该激光器的传输耦合方程进行数值求解。计算得到了一至三阶斯托克斯光输出光强随时间的变化规律和受激拉曼散射的弛豫振荡过程。得出：拉曼谐振腔输出耦合镜对一阶斯托克斯光的反射率越高,拉曼谐振腔内的一阶斯托克斯光功率密度就越高,越有利于泵浦光向二阶斯托克斯光的转换。     

Output Characteristics of High-Power Continuous Wave Raman Fiber Laser at 1484 nm Using Phosphosilicate Fiber

A continuous wave (CW) high-power Raman fiber laser (RFL) with maximum output power of 2.24 W and slope efficiency of 32.8% at 1484 nm is obtained using a CW 8.4 W/ 1064 nm Yb-doped double-clad fiber laser as a pump, 700 m phosphosilicate fiber, and cascaded cavities with two pairs of fiber Bragg grating mirrors for the first and the second Stokes orders. Theoretical simulation of the RFL using a very efficient and rapidly converging collocation method is done to understand and optimize the fiber length to obtain maximum second Stokes power. RFL performance for the 300, 700 and 1150 m phosphosilicate fiber lengths was experimentally investigated by observing maximum output power, slope efficiency, threshold power, and full-width at half maximum at the second Stokes wavelength.     

Continuous-wave wavelength conversion for high-power applications using an external cavity diamond Raman laser

We demonstrate continuous-wave (cw) operation of a diamond Raman laser at 1240 nm in an external cavity configuration. The output power increased linearly with pump power with a 49.7% slope efficiency and reached 10.1 W at the maximum available pump power of 31 W. The combination of resonator design with diamond provides a novel approach to power-scalable cw wavelength and beam conversion.     

First-Stokes Wavelengths at 1175.8 and 1177.1 nm Generated in a Diode End-Pumped Nd:YVO_4/LuVO_4 Raman Laser

A diode end-pumped acousto-optic Q-switched Nd:YVO_4/LuVO_4 Raman laser is demonstrated. Both YVO_4 and LuVO_4 can work as Raman gain, and slightly different active vibration modes of both crystals can result in different first-Stokes wavelengths. The output characteristic as the Raman competition between YVO_4 and LuVO_4 crystals for the laser systems with both shared cavity and coupled cavity is experimentally investigated.For the shared cavity, simultaneous Raman conversion in both YVO_4 and LuVO_4 crystals is achieved with dualwavelength emission at 1175.8 and 1177.1 nm. The maximum output power of 1.03 W and the conversion efficiency of 10.3% are obtained. The 0.84 W single first Stokes wavelength at 1177.1 nm with LuVO_4 Raman conversion is achieved with the coupled cavity. The results show that the coupled cavity with short Raman cavity can obtain a narrow pulse width. The separated laser crystal and Raman gain media with different vanadates in shared cavity have advantages in achieving dual-wavelength lasers with small frequency intervals.