溶胶-凝胶法制备丙烯酸树脂/TiO2有机-无机杂化材料及其结构表征

通过预水解的二氧化钛(TiO2 )溶胶与丙烯酸树脂共混或原位聚合的方法制备了均匀透明的丙烯酸树脂 TiO2 有机 无机杂化材料.考察了TiO2 溶胶制备方法、聚合物中—COOH官能团含量和杂化材料制备方法对杂化材料结构的影响.索氏抽提实验表明聚合物中的羧酸官能团和无机TiO2 相间发生了交联反应,且随着—COOH官能团含量的增加,交联程度增大.小角X射线散射(SAXS)结果发现,杂化材料中TiO2 为疏松的三维网状结构,且在纳米尺度范围内,但这种三维网状结构随着TiO2 溶胶制备中水或酸的用量增加,其致密度增加,尺寸增大.同原位聚合法相比,共混法可制备出更均匀的杂化体系,且TiO2 为单分散.     

PMMA/SiO_2/OV-POSS杂化材料的制备与表征

以乙烯基三氯硅烷为原料水解制得八乙烯基多面体低聚倍半硅氧烷(OV-POSS),将其与经KH570改性的SiO2溶胶和甲基丙烯酸甲酯(MMA)混合均匀,采用热固化的方法制得PMMA/SiO2/OV-POSS杂化材料,通过透射电镜、红外谱图、差热分析和热重分析对材料的微观结构以及热性能进行表征,结果表明:杂化材料结构均匀,有机相和无机相之间通过双键聚合的方式形成了共价键;杂化材料耐热性好,玻璃化转变温度比纯PMMA提高约72℃,分解温度提高约121℃。     

PMMA/SiO_2透明块体材料的制备及其热性能

以正硅酸乙酯为前驱体,采用无溶剂水解技术,制备出了均一、稳定、透明的SiO_2溶胶,通过透射电子显微镜分析,粒径在100 nm左右;在溶胶中加入甲基丙烯酸甲酯(MMA)和偶氮二异丁腈(AIBN),采用热固化制备了透明的块体PMMA/SiO_2杂化材料,通过差热(DSC)和热重分析(TGA)研究了杂化材料的热性能. DSC结果表明,当体系中的SiO_2质量分数超过20%时,杂化材料无明显的玻璃化转变现象. TGA结果表明,杂化材料的分解温度提高约110 ℃. 透射电子显微镜观察结果表明,无机相均匀分散在有机相中,两相之间没有明显的相分离现象.     

纳米TiO_2-SnO_2介孔材料的制备及其对含氰废水的光催化降解性能

以TiCl4和SnCl4为原料,采用直接水解常压液相反应合成出了纳米TiO2-SnO2复合介孔材料.利用XRD和TEM及漫反射谱等对样品进行了表征,并研究了纳米TiO2-SnO2复合介孔材料对含氰废水的光催化降解性能.结果表明,纳米TiO2与SnO2复合后,导致材料的光谱响应拓宽;此种催化剂在日光灯下比在紫外灯下对废水中CN-的降解效果要好.     

脉冲激光法制备修饰纳米Eu_2O_3/聚苯胺导电杂化薄膜

采用聚焦脉冲激光法(PLA-IT/SFL)制备修饰纳米Eu2O3/聚苯胺有机溶胶及其杂化薄膜材料。考察了制备条件对修饰纳米Eu2O3/聚苯胺有机溶胶荧光性能的影响。TEM显示Eu2O3粒子粒径约为15 nm且其在聚苯胺中有较高的稳定性。荧光光谱表明该杂化薄膜材料在紫外光照射下发出强烈的红光,且荧光强度达2.53×105a.u。杂化薄膜材料的电导率为1.13×10-2S.cm-1。热分析表明该杂化薄膜比导电性聚苯胺(PAN-HCSA)薄膜具有更好的热稳定性。该杂化薄膜材料可望用于电致发光领域。     

PMMA/SiO2透明块体材料的热性能分析与微观结构表征

以正硅酸乙酯为前驱体,采用无溶剂水解技术,制备出了均一、稳定、透明的二氧化硅溶胶,通过透射电镜分析,粒径在100nm左右;在溶胶中加入甲基丙烯酸甲酯（MMA）和偶氮二异丁腈（AIBN）,采用热固化的方式制备出透明的块体PMMA/SiO2杂化材料,通过差热分析、热重和透射电镜表征杂化材料的热性能和微观结构,实验结果表明：当体系中的SiO2含量超过20%时,杂化材料无明显的玻璃化转变温度;无机相均匀分散在有机相中,两相之间没有明显的相分离现象,制备出均一的杂化材料。     

SnO2掺杂对TiO2/Si纳米复合材料性能的影响

采用溶胶-凝胶法在p-型单晶硅的表面镀上一层TiO2-SnO2纳米复合薄膜,并在一定的温度下煅烧得到TiO2-SnO2/Si复合材料.实验研究发现,在TiO2中掺杂一定量的SnO2会使TiO2/Si复合材料的光电压增强,且SnO2的掺杂会抑制TiO2的晶相转变,使复合材料的高温稳定性增强.另外,SnO2的掺杂量和煅烧温度对复合材料的光电压都有影响.当SnO2掺杂量约为20%,煅烧温度为600℃时复合材料的光电压最强.     

由铜-胺氧化还原引发反应一步法简便制备TiO_2表面接枝聚甲基丙烯酸甲酯纳米杂化粒子

提出并验证了一种通过普通自由基聚合在纳米TiO2表面接枝聚甲基丙烯酸甲酯的简单方法.通过在纳米TiO2粒子表面引入伯胺分子层(纳米TiO2-NH2粒子),利用Cu2+-胺氧化还原体系实现了CuSO4催化纳米TiO2-NH2粒子表面引发甲基丙烯酸甲酯(MMA)的自由基接枝聚合,从而一步得到表面固定有聚甲基丙烯酸甲酯链的纳米TiO2杂化粒子(纳米TiO2-PMMA杂化粒子).红外光谱、热失重分析与电镜的结果都表明PMMA已经被接枝到纳米TiO2粒子表面,且接枝率随着聚合时间的延长而逐渐增大,PMMA链的引入有助于降低纳米TiO2粒子微球的团聚程度、增强与有机溶剂分子的范德华力,从而提高分散稳定性.反应溶液中没有游离均聚物形成.     

PVA/SiO2-TiO2杂化电纺纤维膜的形态与性能

以正硅酸乙酯(TEOS)、钛酸四丁酯(TBT)和聚乙烯醇(PVA)为原料, 用溶胶凝胶法制备了PVA/(SiO2-TiO2)杂化纺丝液, 将其电纺成纤维膜. 红外光谱结果证实, PVA的羟基与TEOS和TBT水解后的羟基发生了缩合反应, 杂化电纺纤维膜以网络结构形式相结合; X射线衍射分析表明, 杂化电纺纤维膜的结晶度比纯PVA电纺纤维膜小; 扫描电镜表明, 随杂化纤维膜中无机相含量的增加, 纤维的直径不断增加, 纤维出现一定的弯曲和扭曲, 并伴有少量带状结构的纤维; 紫外-可见光谱结果表明, TiO2的引入增加了纤维膜的抗紫外性; TGA热分析结果表明, 杂化纤维膜的耐热性能优于纯PVA电纺纤维膜的; 耐水性和稳定性测试表明, 杂化纤维膜的耐水性和稳定性优于纯PVA和PVA/SiO2电纺纤维膜的.     

TiO2-SnO2复合氧化物微球的低温水热一步法合成及紫外屏蔽性能

以硫酸钛、 四氯化锡和尿素为原料, 采用低温水热法一步合成了TiO2-SnO2复合氧化物. 采用X射线衍射(XRD), 扫描电子显微镜/能量色散X射线谱仪(SEM/EDAX)及紫外-可见光谱(UV-Vis)对产物的结构与性能进行表征分析, 考察了反应条件对产物晶体结构和形貌的影响. 结果表明, 在静止反应条件下Ti4+/Sn4+摩尔比为6~8时, 可以获得尺寸均一的金红石结构TiO2-SnO2复合氧化物微球, 其平均粒径为2 μm. 产物的紫外吸收性能优于同种方法制备的纯TiO2, SnO2及商品P25.     

喹哪啶酸合铕/二氧化硅发光材料的溶胶-凝胶法合成与性能

通过红外光谱、紫外可见光谱、荧光光谱和X射线粉末衍射等测试手段,对溶液中合成的喹哪啶酸合铕(Eu-qina)配合物进行了表征,且将溶胶-凝胶法合成出的Eu-qina/SiO2杂化发光材料,与溶液中合成的配合物Eu-qina进行对比.结果表明,配合物Eu-qina中由于喹哪啶酸能有效地将能量传递给Eu3+离子,使Eu3+发出较强的红色特征荧光,而杂化材料Eu-qina/SiO2因SiO2的加入使荧光强度增大.当Eu-qina配合物的掺杂量达到一定值时,Eu-qina/SiO2发较强的红光,并由晶态的Eu-qina转化为非晶态的Eu-qina/SiO2.     

不同紫外光源下MnO2对TiO2光催化活性的影响

采用动力学方法研究了3种紫外光源下MnO2颗粒物对TiO2光催化活性的影响, 使用的光源包括UV365/28 W, UV302/16 W和UV254/25 W, 实验用的MnO2包括α-MnO2, β-MnO2和δ-MnO2. 实验结果表明, 当水悬浮液中有MnO2颗粒物存在时, 在UV365/28W和UV302/16W两种紫外光源下TiO2光催化剂会失活, 而在UV254/25W紫外光源下TiO2光催化剂能基本保持稳定. TiO2光催化剂的稳定性与使用的紫外光源的波长有关.     

Preparation of photocrosslinked sol‐gel composites based on urethane‐acrylic matrix,silsesquioxane sequences,TiO2, and Ag/Au Nanoparticles for use in photocatalytic applications

An acid urethane oligodimethacrylate based on poly(ethylene glycol) was synthesized and used in the preparation of hybrid composites containing silsesquioxane sequences and titania domains formed through sol‐gel reactions along with silver/gold nanoparticles (Ag/Au NPs) in situ photogenerated during the UV‐curing process. The photopolymerization kinetics studied by Fourier transform infrared spectroscopy and photoDSC showed that the photoreactivity of the investigated formulations depends on the amount of titanium butoxide (5–20 wt %) added in the system subjected to UV irradiation. The introduction of 1 wt % AgNO₃/AuBr₃ in formulations slightly improved the degree of conversion but diminished the polymerization rates. The formation of hybrid materials comprising predominantly amorphous TiO₂/SiO₂ NPs, with or without Ag/Au NPs, was confirmed through specific analyses. The evaluation of photocatalytic activity demonstrated that the synthesized hybrid films are suitable for the complete removal of organic pollutants (phenolic compounds) from water under UV irradiation (200–350 min) at low intensity (found in the solar radiation). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1189–1204     

UV curing of organic–inorganic hybrid coating materials

The effect of UV-curing time on the mechanism of interaction between the various precursor phases in a novel sol–gel-derived organic–inorganic hybrid coating material and the resulting mechanical and thermal properties of this material when coated onto substrates in thin film form have been examined using a variety of chemical and physical characterisation methods. Microstructurally, the hybrid coating materials examined were all a single amorphous phase and were all optically transparent. The degree of interaction between the organic and inorganic phases, the scratch behaviour of the coating materials and the thermal stability of the coating materials were all found to depend strongly on the UV curing time. For the particular proportions of inorganic and organic components used to make up this hybrid coating material, an optimum UV curing time of 10 min under a UV intensity of 46.3 mW cm⁻² was found to produce transparent coatings which adhered well to the substrates and which were robust in scratch tests on aluminium and polycarbonate substrates and abrasion tests on polycarbonate substrates.     

Preparation and Characterization of Epoxy/Inorganic Anti‐electrostatic Nanocomposites Using Submicrometer Al(OH)3 and Colloid Al2O3

New organic‐inorganic hybrid materials and their anti‐electrostatic hybrid membranes are prepared via sol‐gel process. The polycondensation of epoxy oligomers and AEAPS/Al₂O₃ complexes which are organically surface modified submicrometer aluminum trihydroxide inorganic fillers with an active aminoterminal silane coupling agent, N‐(2‐aminoethyl)‐3‐aminopropyltrimethoxysilane (AEAPS), are performed. AEAPS enhances the interfacial interactions between the inorganic fillers and epoxy polymers. Meanwhile, this coupling agent maintains well dispersion of fillers in these composites. To improve the mechanical strength and thermal stability, pyromellitic dianhydride (PMDA) is used as curing agent. These hybrid films prepared from this method have excellent physical properties, such as UV‐shielding, high transmission in visible resign (> 85%), high hardness (7～8H) , high adhesive force (7～8) and low relative surface resistance (9.71 × 10¹¹～1.26 × 10¹⁰ Ω/cm²) with anti‐electrostatic characters. For thermal resistance, the best Td value of epoxy/PMDA/AEAPS/Al₂O₃ is 378.6 °C which is 85.4 °C higher than that of neat epoxy resin. Physical properties of these materials are almost the same as those of the nanocomposites prepared from expensive colloid Al₂O₃. Evidences from TEM micrograph show that the inorganic additives are dispersed evenly in organic matrix with nanometer scale.     

Synthesis of Poly(2‐Hydroxyethyl Methacrylate)‐based Hybrid Nanoparticles via Visible‐Light‐Initiated Radical Polymerization

We report a new, unique process for the design of poly(2‐hydroxyethyl methacrylate) (PHEMA )‐based hybrid materials, which involves the coating of PHEMA on TiO₂ and TiO₂ /Ag nanoparticle surface under visible light. New hybrid materials initiated under different conditions were prepared under visible light, which could be used for the theoretical design of nanohybrid materials. The hybrid materials thus prepared were characterized by Fourier transform infrared spectroscopy (FTIR ), transmission electron microscopy (TEM ), and thermogravimetric analysis (TGA ). The experimental results confirmed the successful synthesis of TiO₂–PHEMA hybrid materials. Compared to other methods, the method reported here involving the direct combination of PHEMA on the TiO₂ surface was simply catalyzed by visible light without the addition of initiators.     

凹凸棒黏土-SnO2-TiO2复合材料的制备及其光催化性能

以凹凸棒黏土为基体,通过原位溶胶-凝胶包覆工艺,将SnO2-TiO2复合氧化物负载于凹凸棒黏土表面制备凹凸棒黏土复合光催化剂(Att-SnO2-TiO2)。采用XRD、BET、TEM等分析测试技术对产物进行了表征。结果表明,SnO2-TiO2复合氧化物均匀地负载于凹凸棒黏土表面,其平均粒径约为10 nm;经过复合氧化物负载改性后,凹凸棒黏土的表面形貌得到明显改善,产物的包覆效果好、比表面大。以光催化降解甲基橙为探针,研究了凹凸棒黏土复合光催化剂的光催化性能。结果表明,凹凸棒黏土复合光催化剂显示出优异的光催化性能,其光催化活性顺序为Att-SnO2-TiO2>Att-SnO2>Att-TiO2。以性能最佳的Att-SnO2-TiO2为催化剂光降解甲基橙30min后,甲基橙的降解率达99%。实验表明,Att-SnO2-TiO2复合光催化剂可重复利用。     

质量比对基于CuInSe2/P3HT纳米复合材料光检测器件性能的影响

利用CuInSe2纳米材料与P3HT共混形成纳米复合材料,并由此构筑了具有高开关比的原理性光检测器件.研究发现,两种材料的混合比例对器件的性能有明显影响.随着CuInSe2纳米颗粒含量的增加,器件的开关比先增加后减小,而响应时间则一直减小.     

离子交换-双氧水氧化法制备纳米CeO2晶体

以99.995% Ce(NO₃)₃和强碱性阴离子交换树脂为原料，采用离子交换-双氧水氧化法合成制备出纳米CeO₂晶体。并就离子交换反应中的Ce³⁺浓度、树脂加入速度和离子交换温度及H₂O₂加入速度等条件对CeO₂粒径的影响进行了探讨，得出了离子交换-双氧水氧化法制备纳米CeO₂晶体的最佳工艺条件。FTIR、TEM分析表明，离子交换法无需对合成的Ce(OH)₃溶胶进行洗涤即可去除NO₃^-、CO₃^2-等阴离子杂质，并用H₂O₂将该溶胶氧化，经真空干燥可制得粒径分布均匀，平均晶粒尺寸约3 nm，高纯度的CeO₂粉体。