聚醚醚酮酮的结晶熔融行为

用差示扫描量热法（ＤＳＣ）研究不同热历史聚醚醚酮酮（ＰＥＥＫＫ）的结晶熔融行为。在２２５－３００℃等温热处理样品的ＤＳＣ曲线出现了熔融双峰。低温熔融峰峰温（Ｔｍｌ）较低，Ｔｍｌ与热处理温度Ｔｃ有关；高温熔融峰峰温（Ｔｍ２）较高，Ｔｍ２几乎不受Ｔｃ的影响。研究结果认为，在升温过程中存在结晶的熔融－重结晶过程，熔融双峰归因于结构相同而完整程度不同的ＰＥＥＫＫ结晶的熔融行为。还探讨了升温速度对结晶熔融行     

取向对物理老化的聚对苯二甲酸乙二酯纤维溶剂诱导结晶速率的影响

通过密度法、ＤＳＣ、力学性能测试等方法研究了物理老化对聚对苯二甲酸乙二酯（ＰＥＴ）纤维溶剂诱导结晶速率及结构的影响，并进一步探讨了取向程度对ＰＥＴ纤维物理老化过程的影响．发现在一定老化温度下，ＰＥＴ纤维的溶剂诱导结晶（ＳＩＮＣ）速率随老化时间的延长呈现先降低后升高的趋势；取向程度高的样品则经较短的老化时间即可出现这种情况．对上述现象用凝聚缠结的观点加以解释．     

刚性聚芳醚腈合成与性能研究

用２，６ 二氟苯甲腈和间苯二酚为原料，在碱性条件下，于非质子极性溶剂中，通过溶液高温缩聚法制备聚芳醚腈［Ｐｏｌｙ（ｃｙａｎｏａｒｙｌｅｔｈｅｒ）ＰＣＥ］．并用ＩＲ、ＤＳＣ、ＴＧ、ＷＡＸＤ等手段对其结构及热性能、结晶行为进行了研究．结果表明，ＰＣＥ高聚物不仅具备较好的耐高温和耐热老化性能，而且具有较好的结晶性能．同时，用对比的方法，对ＰＣＥ的晶体结构进行了初步的探讨．     

聚对苯二甲酸乙二酯／热致液晶聚合物共混体系中液晶组分的诱导结晶效应

用差示扫描量热法对聚对苯二甲酸乙二酯（ＰＥＴ）／热致液晶高分子（ＬＣＰ）共混体系的等温和非等温结晶行为进行了研究．结果表明，由于液晶组分的加入，共混体系中ＰＥＴ的结晶速率和结晶度均得到提高．说明ＬＣＰ具有ＰＥＴ结晶成核剂的作用．在较低的ＬＣＰ组分含量下（～２ｗｔ％），这一效果最为明显，说明ＬＣＰ是以很小的微区或某些ＬＣＰ分子链介晶微束的形式对ＰＥＴ的结晶起成核剂的作用．     

聚丙烯接枝马来酸酐及其离聚物的非等温结晶动力学

用 Ｄ Ｓ Ｃ 测定了固相接枝法制备的聚丙烯接枝马来酸酐（ Ｐ Ｐ ｇ Ｍ Ａ Ｈ） 及其３ 种５ 个离聚物在不同冷却速率的非等温结晶动力学．分析了结晶峰温（ Ｔｍａｘ） 、结晶起始温度（ Ｔ０） 、结晶峰的初始斜率（ Ｓｉ） 及结晶峰的半高宽（ Δｗ ） 等结晶峰参数;用 Ａｖｒａｍｉ 方程和综合了 Ａｖｒａｍｉ Ｏｚａｗａ 方程的方法处理非等温结晶动力学．对于全部样品在所有的冷却速率下, Ａｖｒａｍｉ 指数ｎ 值均在２５ ～２８ 之间,说明聚丙烯结晶行为没有改变;但同时发现接枝及离子化后,成核速率加快,晶粒分布变窄,结晶总速率增大,与等温结晶动力学得到的结论一致．     

FRS-XRSA表征双轴取向聚对苯二甲酸乙二酯薄膜的取向分布

Ｘ－射线散射理论分析（ＦＲＳ－ＸＲＳＡ）是作者为了研究和表征取向高聚物结晶度与晶粒取向分布（ＯＤＣ）的一种新方案．在表征ＯＤＣ方面应用分峰法（ＣＰＲ）消除了传统极图法（ＰＦＭ）中高重叠峰相互干扰的困难，克服了取向分布函数分析（ＯＤＦＡ）中出现虚织构的困难，并且经一次系统的ＦＲＳ－ＸＲＳ测定，可以得到几乎所有主要（ｈｋｌ）晶面法向的ＯＤＣ．作者应用ＦＲＳ－ＸＲＳＡ对二类双轴取向ＰＥＴ磁带薄膜进行了ＯＤＣ的研究。基于结晶几何学原理（ＣＧＰ），建立了三斜晶系晶粒坐标系与试样坐标系的关系，并用于推演未测定方位角（αｉ，βｉ）（ｈｋｌ）的晶面散射以及未测（ｈ′ｋ′ｌ′）晶面的ＯＤＣ．作者关系建立了双轴取向函数〈ｃｏｓ２φｈｋｌ，ｉ〉，ｉ＝Ｎ、Ｍ、Ｔ的计算公式．按照ＦＲＳ－ＸＲＳＡ获得了反映取向分布的１０个晶面的双轴极图、三个主晶面（１００）、（０１０）、（１０５）的总极图，以及反映平均取向的各种取向函数，如〈ｃｏｓ２φｈｋｌ，ｉ〉、ｆｃｈｋｌ，ｉ等，结果十分令人满意．     

取向态聚对苯二甲酸乙二酯膜热弛豫过程的偏振红外光谱研究

用升温在位偏振红外光谱测量方法，研究了不同取向态的聚对苯二甲酸乙二酯（ＰＥＴ）膜在热弛豫过程中的尺寸变化以及分子链构象和取向的变化．结果说明，ＰＥＴ小尺度取向链段的热弛豫较大尺度取向分子链的热弛豫在较低的温度下发生，取向ＰＥＴ膜的热收缩主要与分子链大尺度取向的弛豫有关，而其后的自发伸长是结晶过程引起的，分子链的取向程度对结晶伸长的幅度有着重要影响．     

直接酯化法合成PET反应条件对树脂结晶速率的影响

用直接酯化法合成了聚对苯二甲酸乙二酯（ＰＥＴ）。对缩聚反应温度、真空度及稳定剂等合条件对产物结晶速率的影响进行了研究。以ΔＴｃ＝Ｔｃ－Ｔｇ和ΔＴｃｏ＝Ｔｃｏ－Ｔｇ表征样品的结晶速率。结果表明，真空度一定，反应温度高则样品结晶速率慢；温度一定，真空度高样品结晶速率也慢。这两个因素的影响均是不可忽视的。     

刚性链嵌段共聚物的研究（Ⅳ）──聚醚醚酮／苯酞圈型聚芳醚砜有规嵌段共聚物的合成与部分性能

以聚醚醚酮（ＰＥＥＫ）和苯酞圈型聚芳醚砜（ＰＤＣ）齐聚物为原料，通过溶液缩聚法制备了ＰＥＥＫ／ＰＤＣ有规嵌段共聚物系列样品。经ＤＳＣ、ＷＡＸＤ、ＴＧＡ、ＤＭＡ等方法研究表明：共聚物没有微相分离现象；其结晶属于简单正交晶系，ＰＤＣ含量对共聚物结晶行为产生很大影响；热稳定性随ＰＤＣ含量增加而明显降低；共聚物具有优异的力学性能，拉伸强度和储能模量高于ＰＥＥＫ。     

浇铸尼龙－6的结晶与熔融

用ＤＳＣ法研究了Ｌａ＿２Ｏ＿３和Ｙ＿２Ｏ＿３对浇铸尼龙－６（ＭＣ尼龙－６）结晶与熔融的影响。二者都使ＭＣ尼龙－６熔体等速降温的结晶温度Ｔ＿ｃ升高、等速升温的溶点Ｔ＿ｍ降低、结晶度Ｘ＿ｃ降低，拉伸过程的断裂能密度及断裂伸长率提高。Ｌａ＿２Ｏ＿３使ＭＣ尼龙－６平衡熔点只降低，结晶速率增加，结晶完善程度变差。Ｙ＿２Ｏ＿３使ＭＣ尼龙－６的升高，它可显著改善ＭＣ尼龙－６的耐热性。     

POLYMETHYLMETHACRYLATE FILMS IN THE STATE OF HIGH GLOBAL CHAIN ORIENTATION BUT NEARLY RANDOM SEGMENTAL ORIENTATION*

PMMA films in the high global chain orientation and nearly random segmental orientation(GOLR) state were prepared by uni-axially drawing at temperatures 20～30℃ above its glass transitiontempefature, T_g, and their isotropic and anisotropic properties were studied. Experimental results show thatthis kind of amorphous state, the GOLR state, is nearly isotropic in optical birefringence, IR-dichroism andX-ray diffraction patterns, but is very anisotropic in behaviors of thermal expansion, solvent-swelling andstress-strain.     

分子链大尺度高取向而小尺度接近无规取向态的非晶态聚对苯二甲酸乙二酯膜片

对非晶态聚对苯二甲酸乙二酯膜片经在Ｔｇ以上单轴拉伸然后淬冷至室温的试样，其物理性质的各向同性或各向异性进行了研究．实验结果说明这种分子链大尺度高度取向而小尺度接近无规取向的非晶态（ＧＯＬＲ态）其折光指数和小形变的拉伸模量是接近各向同性的，而热导率和微波介电常数很可能是各向异性的．     

Relaxation of Chain Extension of Amorphous PET Fiber Above the Glass Transition Temperature

The average relaxation time for segmental orientation is considerably shorter than that for chain extension1,2, due to the difference of the ability to move between segments and chains. So in certain time intervals, an almost total relaxation of the segmental orientation can take place with little relaxation of global chain extension. Under the controlled conditions1,3, high global chain orientation but nearly random segmental orientation (GOLR) state can be achieved. Through the hot shrinka…     

The state of high global chain orientation but nearly random segmental orientation of amorphous polymers

In the rubbery state of amorphous polymers under uni-axial drawing the global chain orientation will relax in orders of magnitude slower than the relaxation of local segmental orientation. When this state of hot drawn sample is frozen at temperatures lower than its glass transition, T_g, an amorphous state with high global chain orientation but nearly random segmental orientation (GOLR) could result. Experimentally the GOLR state of amorphous polymers is easily realized by uni-axial drawing the polymer at temperatures 20–30°C above its T_g. The characteristic features of a GOLR state are i) large recovery of the elastic deformation of global chain on being heated to temperatures above T_g, ii) very small birefringence and IR dichroism, iii) nearly isotropic sonic and ultrasonic velocity of propagation, iv) nearly isotropic WAXD pattern, while it shows v) pronounced anisotropy in stress-strain behavior for large deformations and vi) appreciable anisotropy of thermal conductivity and of microwave dielectric properties. Concrete examples with detailed experimental results will be reviewed.     

AMORPHOUS POLY(ETHYLENE TEREPHTHALATE) FILMS IN THE STATE OF HIGH GLOBAL CHAIN ORIENTATION BUT NEARLY RANDOM SEGMENTAL ORIENTATION

The isotropy or anisotropy in some physical properties of the ammorphous poly(ethyleneterephthalate) films uniaxially drawn at temperatures above its T_g and then quenched toroom temperature have been studied. Experimental results here presented show that thisamorphous state of high global chain orientation but nearly random segmental orientation,the GOLR state, is nearly isotropic in refractive indices and Young's modulus for smalldeformation, while it is very probably anisotropic in thermal conduction and microwavedielectric properties.     

聚对苯二甲酸乙二酯非晶态膜片单轴热——拉伸中的结晶与松弛

用动态力学损耗温度谱作为测试手段,研究了非晶态PET膜片在78—112℃温度范围内的单轴拉伸。实验结果说明,在较低温度下所得结晶的拉伸试样,完全由于应变诱发结晶,发生在应力-应变曲线的屈服后应力开始上升的阶段。在较高温度下(90℃或更高)拉伸可得非晶态而且光学各向同性的试样,是由于分子链的小尺度取向在拉伸过程中已完全热松弛所致,而分子链的大尺度取向要通过高弹态流动而松弛,其速率较慢,用拉伸后试样两端固定时的应力松弛进行了观察。在较低温度下应力松弛后仍为非晶态,在较高温度下应力松弛到起始应力的1O％下才开始结晶。FTIR研究表明在这种状态下的结晶有一结晶诱导期,其时间尺度与应力松弛阶段相当。     

大区域取向对非晶态聚对苯二甲酸乙二酯结晶的影响

大区域取向对非晶态聚对苯二甲酸乙二酯结晶的影响林辛，吴永升，高金贵，范庆荣（中国科学院化学研究所北京１０００８０）关键词聚对苯二甲酸乙二酯，溶剂诱导结晶，大区域取向Ｓｌｏｎｉｍｓｋｙ等’‘’“最早注意到区分小区域取向和大区域取向的概念，钱人元等”’对...     

大区域取向对非晶态聚对苯二甲酸乙二酯结晶的影响

ffects of the chain orientation in the global sense on the solvent induced crystallization (SINC),diffusion velocity of toluol into poly(ethylene terephtlialate)(PET)and crystallization morphology were:studied by using density measurement and SEM.It has been shown that the SINC and diffusion velocity of toluol into PET increase with increasing degree of chain orientation in global sense,and the chain orientatioll can be essentially remained during SINC.     

RECOVERY OF AMORPHOUS POLY(ETHYLENE TEREPHTHALATE)FILM UNIAXIALLY DRAWN JUST BELOW THE GLASS TRANSITION TEMPERATURE*

Isothermal recovery in the macroscopic length of homogeneously deformed specimens of amorphous poly(ethyleneterephthalate) (PET) film sample uniaxially drawn at 69℃ to the draw ratios λ_0=1.26～2.20 were studied at temperaturesaround the glass transition temperature (T_g = 73℃). Experimental results indicate that the length recovery took place in twodistinct steps: a fast first step (fast relaxation) followed by a slow second step (slow relaxation). The relaxation processeswere accompanied by the reversion of trans-conformers (1340 cm~(-1)) to gauche, and the dichroic function of the 1340 cm~(-1)band characterizing the segmental orientation along the chain direction decreased to a very low value at the end of the fastrelaxation. This fact led us to assign the fast relaxation as the segmental orientation while the slow relaxation as relaxation ofthe global chain orientation. It was found that the slow relaxation follows a single exponential function, with relaxation timesstrongly dependent on the temperature resembling the glass transition process. The fast relaxation does not follow a singleexponential decay, presumably a distribution of relaxation times is involved.     

链解缠结聚对苯二甲酸乙二酯的结晶行为研究

采用冷冻萃取聚对苯二甲酸乙二酯(PET)溶液(0.1～10g/dL7种不同浓度,3种不同性能溶剂)的方法制备了解缠结PET试样.与链相互穿透且缠结的熔体骤冷试样相比,解缠结PET试样的结晶能力明显增强,且随着制样溶液浓度的降低,链间解缠结程度增加,PET的结晶能力逐渐增强,有序结构含量明显增加,但是如果制样溶液浓度太低,溶液中链间距离太大,则又不利于萃取过程中链间的有序堆砌而结晶.采用接触浓度c*附近的溶液,既可确保链间的有效解缠结又有利于链间的有序堆砌而结晶.PET的结晶能力甚至还受制样所用溶剂性能的影响,这是因为溶剂性能影响了溶液中链间的相互作用以及链的解缠结程度.