147 fs碳纳米管倏逝场锁模全光纤掺铒光纤激光器

利用化学腐蚀法在光纤包层表面成功制备了调制深度为3.9%的单壁碳纳米管饱和吸收体.组建了环形腔结构的全光纤掺铒光纤激光器,以制备的单壁碳纳米管薄膜为锁模元件,利用倏逝场锁模实现了锁模输出.锁模脉冲的中心波长为1556 nm,3 dB光谱带宽为24 nm,脉冲宽度为147 fs,重复频率为150 MHz.在520mW抽运功率下,平均输出功率为21 mW,相应的单脉冲能量为0.14 nJ.     

氧化石墨烯被动锁模掺镱光纤激光器多脉冲现象的实验研究

利用氧化石墨烯作为可饱和吸收体,在被动锁模全正常色散掺镱光纤激光器中研究了多脉冲的现象,在同一抽运功率不同偏振态下,实验获得了矩形脉冲谐波锁模、耗散孤子谐波锁模、准谐波锁模,脉冲峰值周期性调制,脉冲簇、脉冲束、混沌多重脉冲的多脉冲现象,插入激光腔内的2nm窄带滤波器具有限制增益带宽、对脉冲塑形、诱导多脉冲产生的作用,调节偏振控制器相当于改变腔内增益,是实现不同类型多脉冲现象的主要原因,本实验研究有利于加深对多脉冲动力学行为在正常色散区域氧化石墨烯锁模掺镱光纤激光器中的理解。     

Switchable mode-locking states in an all-fiber all-normal-dispersion ytterbium-doped laser

Multi-operation state in an all-normal-dispersion ytterbium-doped fiber laser is obtained by introducing nonlinear polarization or hybrid mode-locking mechanism in the laser cavity. In addition to operating the laser at continuous-wave mode-locking, various operation states including continuous-wave, Q-switched mode-locking, pulse-splitting, and harmonic mode-locking can be achieved by tuning the laser pump power or an intracavity polarization controller. Insertion of a semiconductor saturable absorber mirror in the cavity helps to shorten the output pulsewidth of the hybrid mode-locked laser. When the pump power is rapidly adjusted, a strong asymmetric hysteresis behavior can be observed during the manipulation between different orders of harmonic mode-locking.     

高能量掺Yb偏振型大模场面积光子晶体光纤孤子锁模飞秒激光器

实验研究了基于掺Yb偏振型大模场面积光子晶体光纤的孤子锁模激光器,获得了高脉冲能量的飞秒激光输出. 激光器基于线形腔结构,利用光栅对补偿腔内色散,并通过半导体可饱和吸收镜实现锁模的自启动. 实验中从振荡级直接获得了平均功率为700mW, 重复频率为47.3MHz(对应于14.8 nJ的单脉冲能量),脉冲宽度为518 fs的稳定锁模脉冲输出. 与普通孤子锁模飞秒光纤激光器相比,输出的单脉冲能量提高了两个数量级. 关键词： 光子晶体光纤 飞秒 光纤激光器 孤子锁模     

基于微纳光纤-单壁碳纳米管可饱和吸收体的被动调Q掺镱光纤激光器

为实现具有高脉冲能量的调Q脉冲激光输出,利用微纳光纤-单壁碳纳米管复合的方法制备可饱和吸收体,并对基于该类型可饱和吸收体器件的被动调Q掺镱光纤激光器进行研究。采用拉伸法将普通单模石英光纤拉制成微纳光纤,将其与单壁碳纳米管溶液复合,进一步制备成全光纤集成型器件。将该器件置于环形腔掺镱光纤激光器中,利用976 nm半导体激光器作为抽运源。当抽运功率为53 mW时,实现了调Q脉冲激光输出,激光中心波长为1 039 nm。进一步提升抽运功率至76 mW,可获得脉冲宽度为3.1μs、重复频率为25.5 kHz、单脉冲能量为941nJ的调Q脉冲激光输出。研究表明,利用微纳光纤制备的可饱和吸收体器件具有较高的损伤阈值,可用于实现高脉冲能量的激光输出。     

Dissipative dispersion-managed soliton 2 μm thulium/holmium fiber laser

We report a first dissipative dispersive-managed soliton fiber laser operating at 2?μm. The cavity comprised of all-anomalous-dispersion fiber employs chirped fiber Bragg grating, which ensures net-normal cavity dispersion and semiconductor saturable absorber for mode-locking.     

输出近百纳焦耳脉冲能量的光子晶体光纤锁模激光器

设计并搭建了一种支持百纳焦耳量级的单脉冲能量输出的锁模光纤激光器.激光器基于σ型腔结构,采用掺Yb偏振型大模场面积光子晶体光纤作为增益介质,利用半导体可饱和吸收镜实现自启动锁模.激光器内没有色散补偿机理,使其工作在全正色散锁模状态.通过在谐振腔内引入多通长腔使激光器的重复频率降低至11.1 MHz,直接获得了平均功率为1.08 W,单脉冲能量为 97 nJ,脉冲宽度为4.17 ps的稳定锁模脉冲输出,经腔外色散补偿,脉冲宽度压缩至740 fs.     

Dynamic control of the operation regimes of a mode-locked fiber laser based on intracavity polarizing fibers: experimental and theoretical validation

An intracavity polarizing fiber is proposed to control the emission regime of a passively mode-locked fiber laser. Stable operation in self-starting high and low dispersion soliton mode-locking and 100 GHz multiwavelength regimes is demonstrated through numerical simulations and experimental validation. Mode-locking stability is ensured by a saturable absorber in the ring cavity. The effective selection of operation regime is dynamically carried out by controlling the intracavity polarization state.     

利用SBR实现自启动锁模钛宝石飞秒激光脉冲的产生

利用国内生长的低损耗双量子阱结构的可饱和布拉格反射器在掺钛蓝宝石激光器中实现了可饱和吸收体被动锁模、孤子锁模和KLM锁模状态的自启动稳定运转.当抽运功率为4.5W时，用啁啾镜进行色散补偿，获得了18fs的KLM锁模脉冲，输出功率为150mW. 关键词： 可饱和布拉格反射器 啁啾镜 飞秒 钛宝石激光器     

Sequential generation of self-starting diverse operations in all-fiber laser based on thulium-doped fiber saturable absorber

Self-starting Q-switching, Q-switched mode-locking and mode-locking operation modes are achieved sequentially in an all-fiber erbium-doped fiber laser with thulium-doped fiber saturable absorber for the first time. The central wavelengths of Q-switching, Q-switched mode-locking and mode-locking operation modes are 1569.7 nm, 1570.9 nm, and 1572 nm, respectively. The mode-locking operation of the proposed fiber laser generates stable dark soliton with a repetition rate of 0.99 MHz and signal-to-noise ratio of 65 dB. The results validate the capability of generating soliton pulse by doped fiber saturable absorber. Furthermore, the proposed fiber laser is beneficial to the applications of optical communication and signal processing system.     

Asymmetric Colliding-Pulse Mode-Locking in InGaAsP Semiconductor Lasers

Asymmetric colliding-pulse mode-locking was successfully demonstrated in an InGaAsP laser. This laser had a single saturable absorber section located partway along the cavity length, and showed mode-locking operation at harmonics of the cavity roundtrip frequency. The method verified that optical pulse repetition up to subterahertz rates can be generated with nearly 1-mm-long mode-locked InGaAsP lasers.     

Diode-pumped passively mode-locked sub-picosecond Yb:LuAG ceramic laser

In this paper the laser activities of a diode-pumped Yb:LuAG ceramic which was prepared by the solid-state reactive sintering method were reported. The maximum output power was 1.86 W in the continuous wave(CW) laser operation,corresponding to a slope efficiency of 53.6%. The CW laser could be tuned from 1030 to 1096 nm by inserting a prism in the cavity. With the assist of a semiconductor saturable absorber mirror(SESAM), passive mode-locking was realized,delivering sub-picosecond pulses with 933 fs duration and an average power of 532 m W at a repetition rate of 90.35 MHz.     

Mode-locked fiber laser using an SU8/SWCNT saturable absorber

We report the fabrication of a saturable absorber based on SU8 single wall carbon nanotube (SWCNT) composite material. Thin films with a controllable thickness can be fabricated using a simple and reliable process. These films can be inserted between two FC/APC connectors in order to have an inline saturable absorber. A passive mode-locked laser was built by interleaving the fiberized saturable absorber in an erbium-doped fiber (L-band) ring cavity laser. The laser produces 871 fs pulses with a repetition rate of 21.27 MHz and a maximum average power of 1 mW.     

Er-doped all-fiber laser mode-locked by graphitic carbon nitride nanosheets

Few-layer graphitic carbon nitride(g-C_3N_4) nanosheets were fabricated and utilized as a saturable absorber for mode-locking in an Er-doped fiber laser with net normal dispersion. The g-C_3N_4/polyvinyl alcohol(PVA) hybrid-film-based saturable absorber has a modulation depth of 4.01% and a saturation intensity of 7.5 MW/cm~2. By integrating g-C_3N_4-PVA mode-locker into the laser cavity, a mode-locked operation could be obtained. The achieved mode-locking pulse centered at 1530.3 nm has a pulse width of 530 ps. Its repetition rate is 40.8 MHz, and the corresponding signal-to-noise ratio is about 55 dB.     

Mode-locked fiber laser in the C-band region for dual-wavelength ultrashort pulses emission using a carbon nanotube saturable absorber

A saturable absorber is commonly employed to generate an ultrashort laser with a mode-locking scheme. In an erbium-doped fiber laser system, the laser regimes of either 1530 or 1550 nm wavelength are procured based on the absorption profile of the erbium-doped fiber. The absorption of the erbium-doped fiber is designed to emit at both wavelengths by controlling the net gain of the laser cavity. Subsequently, simultaneous erbium-doped fiber laser emission is attained at 1533.5 and 1555.1 nm with the pulse duration of 910 and 850 fs, respectively.Therefore, this work maximizes the output portfolios of a mode-locking fiber laser for dual-wavelength ultrashort pulses emission.     

Ultrafast mode-locked dual-wavelength thulium-doped fiber laser using a Mach-Zehnder interferometric filter

A simple and robust method to generate a dual-wavelength mode-locked laser using a tunable Mach-Zehnder filter (TMZF) and a single-wall carbon nanotube (SWCNT) based saturable absorber (SA) is proposed and demonstrated. The proposed laser uses a thulium-doped fiber for lasing in the two-micron region and exploits the interferometric spectrum of the TMZF to produce dual peaks with nearly equal magnitude. SWCNT based SA enables mode-locking at a threshold value of 150.4?mW with distinct dual-wavelength peaks at 1919.2?nm and 1963.7?nm. The peaks have a calculated pulse width of 1.8?ps and 1.6?ps, respectively with a repetition rate of 9.1?MHz with a relatively high optical-signal-to-noise ratio value of 59.1?dB. The output is also observed to remain unchanged over time, indicating high stability. The proposed laser has a promising application, particularly in ultrafast gas molecular spectroscopy and sensing.     

Self modulation phenomena in an external-cavity semiconductor laser

We report the observed self-modulation phenomena in an external-cavity semiconductor laser, in which a slant ridge-loading waveguide was formed for the gain medium. A region beside the ridge at a cleaved end of the waveguide served as a saturable absorber for self-modulation. Under different conditions of injection current and cavity alignment, we observed three laser operation regimes, including pure cw oscillation, constant-amplitude pulse-like signal on the top of a cw component, and amplitude-modulated pulse-like signal coexistent with a cw component. The amplitude modulation phenomenon is different from the previously reported concurrence of mode-locking and self-pulsation. A model was proposed to explain the observed results.     

Generation of domain-wall solitons in an anomalous dispersion fiber ring laser

We report experimental observations performed using a net anomalous dispersion Er-doped fiber ring laser without polarization-selective elements, highlighting the domain-wall solitary pulses generated under the incoherent polarization coupling. By adjusting the pump power and the polarization state appropriately, bright and dark solitons can stably co-exist in the cavity, both centered at 1562.16 nm with a 3-dB spectral width of ～ 0.15 nm and a repetition rate of 3.83 MHz. Moreover, the 0.8 mm long thulium-doped fiber (TDF) facilitated the mode-locking and self-starting of the laser. This is the first demonstration of a laser being used to generate bright and dark solitons synchronously while using TDF as the saturable absorber (SA). Except possessing the all-fiber structure, the laser exhibits good stability, which may have a significant influence on improvement of the pulse-laser design, and may broaden practical applications in optical sensing, optical communication, and soliton multiplexed systems.     

单偏振控制器环形腔光纤激光器实验研究

理论分析了非线性偏振旋转环形腔作为类饱和可吸收体获得脉冲的物理机理。在光纤环形腔结构中,采用单个偏振控制器实现了非线性偏振旋转锁模,直接获得了脉冲宽度为131 fs的超短脉冲输出。实验中,采用性能稳定的976 nm半导体二极管激光器作为抽运源,使用高掺杂浓度的Er3 光纤为增益介质,通过调节偏振控制器,获得了光谱谱宽(3 dB带宽处)为23.5 nm的稳定锁模脉冲输出。脉冲中心波长为1535.9 nm,平均功率为5.91 mW,脉冲重复率为11.20 MHz。     

基于10 m光子晶体光纤的放大自相似锁模振荡器研究

基于单根10 m大模场面积保偏光子晶体光纤, 搭建了带有色散图的放大自相似振荡器; 通过仔细调节腔内色散量的大小以及位于色散补偿端的端镜前的狭缝位置和大小, 实现了稳定的锁模运转, 获得了抛物线形脉冲输出. 输出脉冲的重复频率为8.6 MHz, 脉冲宽度为6.2 ps, 光谱宽度为3.84 nm, 平均功率820 mW, 对应单脉冲能量95 nJ. 这是第一次在自相似振荡器中直接获得重复频率在10 MHz 以下的脉冲输出, 95 nJ也是目前自相似振荡器直接输出的最高脉冲能量. 通过数值模拟证实了在第一个光栅的零级反射处和狭缝滤波后可以分别实现抛物线型脉冲和高斯脉冲的两种锁模脉冲输出.