H2O分子在Fe（100）, Fe（110）, Fe（111）表面吸附的第一性原理研究

采用第一性原理研究了H₂O分子在Fe（100）,Fe（110）,Fe（111）三个高对称晶面上的表面吸附.结果表明,H₂O分子在三个晶面上的最稳定结构皆为平行于基底表面的顶位吸附结构.H₂O分子与三个晶面相互作用的吸附能及几何结构计算结果表明H₂O分子与三个晶面的相互作用程度不同,H₂O分子与Fe（111）晶面的相互作用最强,其次是Fe（100）,相互作用最弱的是Fe（110）表面,而这与晶面原子 关键词： 第一性原理 Fe单晶表面 2O分子')" href="#">H₂O分子 分子吸附     

添加Fe(C5H5)2合成氢掺杂金刚石大单晶及其表征

在Ni₇₀Mn₂₅Co₅-C体系中添加含氢化合物Fe(C₅H₅)₂作为新型氢源, 利用温度梯度法, 在压力为5.5-6.0 GPa、温度为1280-1400 ℃的条件下, 成功合成出氢掺杂的宝石级金刚石大单晶. 通过傅里叶显微红外光谱发现, 随着Fe(C₅H₅)₂添加量的增加, 合成晶体中与氢相关的对应于sp³杂化C-H键的对称伸缩振动和反对称伸缩振动的红外特征峰2850和2920 cm^-1逐渐增强, 而晶体中氮含量却逐渐减少. 通过合成晶体的拉曼光谱分析发现, 金刚石的拉曼峰伴随Fe(C₅H₅)₂的添加向高频偏移, 这表明氢的进入在金刚石内部产生了压应力. 观察扫描电子显微镜图像发现, 在低含量Fe(C₅H₅)₂添加时晶体表面平滑, 而高含量添加时晶体表面缺陷增多, 且呈现出气孔状. 使用新的添加剂Fe(C₅H₅)₂作为氢源, 合成出含氢宝石级金刚石单晶, 丰富了金刚石单晶中对氢的研究内容, 也可为理解天然金刚石的形成机理提供帮助.     

Spontaneous magnetostriction of Y2Fe16Al compound

The structure and magnetic properties of Y₂Fe₁₆Al compound have been investigated by means of x-ray diffraction and magnetization measurements. The Y₂Fe Fe₁₆Al compound has a hexagonal Th$_{2}$Ni$_{17}$-type structure. Negative thermal expansion was found in Y₂Fe₁₆Al compound in the temperature range from 332 to 438K by x-ray dilatometry. The coefficient of the average thermal expansion is \alpha =-3.4\times 10^-5K^-1. The spontaneous magnetostrictive deformations from 293 to 427K have been calculated based on the differences between the experimental values of the lattice parameters and the corresponding values extrapolated from the paramagnetic range. The result shows that the spontaneous volume magnetostrictive deformation \textit{$\omega $}$_{\rm S}$ decreases from 5.4$\times $10^-3to near zero with temperature increasing from 293 to 427K, the spontaneous linear magnetostrictive deformation \textit{$\lambda $}$_{\rm c}$ along the $c$ axis is much larger than the spontaneous linear magnetostrictive deformation \textit{$\lambda $}$_{\rm a}$ in basal-plane in the same temperature range except near 427K.     

Continuous and discontinuous precipitation in Fe-1 at.%Cr-1 at.%Mo alloy upon nitriding; crystal structure and composition of ternary nitrides

The internal nitriding response of a ternary Fe–1 at.%Cr–1 at.%Mo alloy, which serves as a model alloy for many CrMo-based steels, was investigated. The nitrides developing upon nitriding were characterised by X-ray diffraction, scanning electron microscopy, electron probe microanalysis, transmission electron microscopy and atom probe tomography. The developed nitrides were shown to be (metastable) ternary mixed nitrides, which exhibit complex morphological, compositional and structural transformations as a function of nitriding time. Analogous to nitrided binary Fe–Cr and Fe–Mo alloys, in ternary Fe–Cr–Mo alloys initially continuous precipitation of fine, coherent, cubic, NaCl-type nitride platelets, here with the composition (Cr_½,Mo_½)N_¾, occurs, with the broad faces of the platelets parallel to the {1?0?0}_α-Fe lattice planes. These nitrides undergo a discontinuous precipitation reaction upon prolonged nitriding leading to the development of lamellae of a novel, hexagonal CrMoN₂ nitride along {1?1?0}_α-Fe lattice planes, and of spherical cubic, NaCl-type (Cr,Mo)N _x nitride particles within the ferrite lamellae. The observed structural and compositional changes of the ternary nitrides have been attributed to the thermodynamic and kinetic constraints for the internal precipitation of (misfitting) nitrides in the ferrite matrix.     

Synthesis of industrial diamonds using FeNi alloy powder as catalyst

Synthesis of diamond single crystals in Fe80Ni20 C system was carried out in a cubic anvil high-pressure and high-temperature apparatus. This paper reports that the surface morphology and inclusion distribution of the grown diamonds had been observed. It finds that the inclusions in cubic and octahedral diamonds radiated along certain crystal orientation, while the inclusion distribution in cubo-octahedral diamond seemed independent of crystal orientation. By using scanning electron microscope, the surface morphology of the three shapes of diamonds was observed. The results of Mossbauer spectrum indicated that there were iron-inclusions FeaC and Fe-Ni alloy in the diamonds. According to the Fe-C phase diagram, FeaC should have formed during the quenching process. Nickel might have an inhibitory effect on the formation of Fe3C.     

Simulations of C60 bombardment of Si, SiC, diamond and graphite

Molecular dynamics simulations of the 20-keV C₆₀ bombardment at normal incidence of Si, SiC, diamond and graphite targets were performed. The unique feature of these targets is that strong covalent bonds can be formed between carbon atoms from the C₆₀ projectile and atoms in the solid material. The mesoscale energy deposition footprint (MEDF) model is used to gain physical insight into how the sputtering yields depend on the substrate characteristics. A large proportion of the carbon atoms from the C₆₀ projectile are implanted into the lattice structure of the target. The sputtering yield from SiC is ∼twice that from either diamond or Si and this can be explained by both the region of the energized cylindrical tract created by the impact and the number density. On graphite, the yield of sputtered atoms is negligible because the open lattice allows the cluster to deposit its energy deep within the solid. The simulations suggest that build up of carbon with a graphite-like structure would reduce any sputtering from a solid with C₆₀⁺ bombardment.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

金刚石和石墨单晶表面覆盖沉积铬的研究

本文用X射线及电子衍射结构分析对金刚石和石墨单晶表面覆盖沉积铬进行了研究。将细颗粒金刚石或者高定向石墨片埋在经真空去气处理的电解铬粉中,在10^-5—10^-6Torr真空条件下,经高于900℃热处理,在金刚石及高定向石墨表面外延生长了Cr₃C₂和Cr₇C₃。对碳化铬生长的条件及覆盖沉积外延生长的物理机制进行了讨论。 关键词：     

The chemisorption of CO,CO2, C2H2, C2H4, H2 and NH3 on the clean Fe(100) and (111) crystal surfaces

The chemisorption of small molecules (CO, CO₂, C₂H₂, C₂H₄, H₂ and NH₃) has been studied on the clean Fe(110) and (111) crystal faces by low-energy electron diffraction (LEED) and thermal desorption. C₂H₄ and C₂H₂ yield the same sequence of surface structures that change with temperature and crystal orientation. CO and CO₂ chemisorption similarly results in the formation of the same types of surface structures that change with surface temperature and crystal orientation. Ammonia forms several ordered surface structures on both iron crystal faces. All of the molecules decompose as a function of temperature on the iron surfaces as indicated by the Auger and thermal desorption spectra.     

ZrNi5-based hydrogenated phases formed under high hydrogen pressure conditions

Formation of novel hydrides from ZrNi₅ alloy has been confirmed experimentally. After exposure of ZrNi₅ at 0.9 GPa(H₂) and 100 °C for 6 days the alloy transformed into two hydrogenated phases α and β containing initially more than 0.38 and 0.86 hydrogen atoms per formula unit respectively. At ambient conditions both hydrides were extremely unstable. Major part of hydrogen desorbed within few minutes. During this desorption the lattice parameters of both hydrides were continuously reduced what confirms their solid solution character.     

Growth and annealing study of hydrogen-doped single diamond crystals under high pressure and high temperature

A series of diamond crystals doped with hydrogen is successfully synthesized using LiH as the hydrogen source in a catalyst-carbon system at a pressure of 6.0 GPa and temperature ranging from 1255 C to 1350 C.It is shown that the high temperature plays a key role in the incorporation of hydrogen atoms during diamond crystallization.Fourier transform infrared micro-spectroscopy reveals that most of the hydrogen atoms in the synthesized diamond are incorporated into the crystal structure as sp 3-CH 2-symmetric(2850 cm-1) and sp 3 CH 2-antisymmetric vibrations(2920 cm-1).The intensities of these peaks increase gradually with an increase in the content of the hydrogen source in the catalyst.The incorporation of hydrogen impurity leads to a significant shift towards higher frequencies of the Raman peak from 1332.06 cm-1 to 1333.05 cm-1 and gives rise to some compressive stress in the diamond crystal lattice.Furthermore,hydrogen to carbon bonds are evident in the annealed diamond,indicating that the bonds that remain throughout the annealing process and the vibration frequencies centred at 2850 and 2920 cm-1 have no observable shift.Therefore,we suggest that the sp 3 C-H bond is rather stable in diamond crystals.     

Ultrafast delocalization of hydrogen atoms in allene in intense laser fields

Ultrafast delocalization of hydrogen atoms in allene (CH₂=C=CH₂) induced by intense laser fields was investigated by the Coulomb explosion coincidence momentum imaging method. On the basis of the kinetic energy distributions of the fragment ions produced through the two three-body Coulomb explosion pathways, C₃H₄³⁺ ? H⁺ + CH⁺ + C₂H₂⁺\mathrm{C}_{3}\mathrm{H}_{4}^{3+} \rightarrow \mathrm{H}^{+} + \mathrm{CH}^{+} + \mathrm{C}_{2}\mathrm{H}_{2}^{+} and C₃H₄³⁺ ? H⁺ + C₂H⁺ +CH₂⁺\mathrm{C}_{3}\mathrm{H}_{4}^{3+} \rightarrow \mathrm{H}^{+} + \mathrm{C}_{2}\mathrm{H}^{+} +\mathrm{CH}_{2}^{+}, and the proton maps for both pathways, it was shown that the decomposition proceeds in a stepwise manner as well as in a concerted manner. The time scale of the hydrogen migration within an allene molecule was estimated to be ∼20 fs.     

Theoretical investigation of the optical spectra and local lattice structure for Mn5+ in a Sr10(VO4)6F2 crystal

In this paper, the relationships between the optical spectra and local lattice structure for Mn⁵⁺ in a Sr₁₀(VO₄)₆F₂ crystal are established by the crystal- and ligand-field theory. The effect of spin–orbital coupling between the central 3d² ions and ligand ions has been considered in the full energy matrix. Using the matrix and superposition model formula, we have calculated the optical spectra and local lattice structure parameters of Mn⁵⁺ in Sr₁₀(VO₄)₆F₂ with a C_3v system. The calculated results are in good agreement with the observed values. In addition, the trigonal compressed distortions of the (MnO₄)^3? centers in Sr₁₀(VO₄)₆F₂ crystals are also obtained from the calculations.     

高温高压下氮氢协同掺杂对{100}晶面生长宝石级金刚石的影响

在压力为5.5–6.2 GPa, 温度为1280–1450 ℃的条件下, 利用温度梯度法详细考察了氮氢协同掺杂对100晶面生长宝石级金刚石的影响. 实验结果表明伴随合成腔体内氮、氢浓度的升高, 合成条件明显升高, 金刚石生长V形区间上移; 晶体的红外光谱中与氮相关的吸收峰急剧增强, 氮含量可达2000 ppm, 同时位于2850 cm^-1和2920 cm^-1对应于 sp³杂化 C–H 键的对称伸缩振动和反对称伸缩振动的红外特征峰逐渐增强, 表明晶体中既有高的氮含量, 同时又含有氢. 对晶体进行电镜扫描发现, 氮氢协同掺杂对晶体形貌影响明显, 出现拉长的{111}面, 且晶体表面上有三角形生长纹理. 拉曼测试表明, 晶体的峰位向高频偏移、半峰宽变大, 说明氮、氢杂质的进入对晶体内部产生了应力. 本文成功地以{100}晶面为生长面合成出高氮含氢宝石级金刚石单晶, 在探究氮氢共存环境下金刚石生长特性的同时, 也可为理解天然金刚石的形成机理提供帮助.     

NQR Study of Phase Transition and Cationic Motion in 4-NH2C5H4NHBiBr4·H2O

Four ⁸¹Br NQR lines in 4-NH₂C₅H₄NHBiBr₄·H₂O were observed in the temperature range between 77 and ca. 380 K; with increasing temperatures the respective sets of higher and lower two resonance lines coalesced into single lines discontinuously at 274 K, showing the occurrence of a first-order type phase transition of this crystal. The transition was confirmed with heat anomaly on a DTA curve. Each higher and lower line of high-temperature phase is assignable to the terminal Br atoms and the bridging ones of one-dimensional poly anions (BiBr₄ ⁻) _n in the crystal structure (C2/c), which was investigated by a X-ray structure analysis at room temperature. The 1/T ₁ temperature dependence of ⁸¹Br NQR follows the usual T ² law in the temperature range between 77 and ca. 140 K, being explained by fluctuation of the EFG at Br nucleus due to lattice vibrations. The T ₁ vs. 1/T curve in the temperature range between about 160 and 190 K was describable by the exponential curves, allowing us the estimation of activation energies. These exponential behaviors of T ₁ of ⁸¹Br NQR are attributable to the fluctuations caused by the thermal motion of 4-NH₂C₅H₄H⁺ ions. Echo signals of the ⁸¹Br NQR could not be detected above 190 K owing to poor S/N with very short T ₂.     

高温高压下掺硼宝石级金刚石单晶生长特性的研究

本文在5.1—5.6 GPa,1230—1600℃的压力、温度条件下,以FeNiMnCo作为触媒,进行单质硼添加宝石级金刚石单晶的生长研究.借助于有限元法,对触媒内的温度场进行模拟.研究得到了FeNiMnCo-C-B体系下,金刚石单晶生长的P-T相图.该体系下合成金刚石单晶的最低压力、温度条件分别为5.1 GPa,1230℃左右.研究发现,在单晶同一{111}扇区内部,硼元素呈内多外少的分布规律.有限元模拟结果给出,该分布规律是由在晶体生长过程中,{111}扇区的增长速度逐渐减小所致.{111}晶向的晶体生长实验结果表明,硼元素优先从{111}次扇区进入晶体.研究发现,这是该扇区增长速度相对较快,硼元素扩散逃离可用时间短导致的.另外,同磨料级掺硼金刚石单晶生长相比,对于温度梯度法生长掺硼宝石级金刚石单晶,由于晶体的增厚速度较慢,即使硼添加量相对较高,也可以实现表面无凹坑缺陷的优质金刚石单晶的生长.     

Magnetic structure and preferential occupation of Fe in the composite compound Nd2Co6Fe

The crystal and magnetic structures of the composite compound Nd₂Co₆Fe have been investigated by high-resolution neutron powder diffraction and X-ray powder diffraction. The compound crystallizes in the hexagonal Ce₂Ni₇-type structure consisting of Nd(Co,Fe)₂ and Nd(Co,Fe)₅ structural blocks alternately stacked along the c-axis. Multi-pattern Rietveld refinement of neutron diffraction and X-ray diffraction data at room temperature reveal that substitution of Fe for Co occurs exclusively in the Nd(Co,Fe)₅ structural blocks. The preferential occupation of the Fe atoms in the structure is discussed based on the mixing enthalpy between Nd and Fe atoms and on the lattice distortions. In agreement with the reported magnetic phase diagram of the Nd₂Co_7−xFe_x compounds, magnetic structure models with the moments of all atoms in the ab plane at 300 K and along the c-axis at 450 K provide a satisfactory fitting to the experimental neutron diffraction data. The refinement results show that the atomic moments of (Co,Fe) atoms within the Nd(Co,Fe)₅ blocks decrease slightly with temperature, whereas the atomic moments of Nd in the compound and of (Co,Fe) atoms at the interface between the Nd(Co,Fe)₂ and Nd(Co,Fe)₅ blocks are reduced significantly.     

内掺过渡金属非典型富勒烯M@C22(M=Sc, Ti, V, Cr, Mn, Fe, Co, Ni) 几何结构、电子结构、稳定性和磁性的密度泛函研究

采用密度泛函理论中广义梯度近似对非典型富勒烯C₂₂和过渡金属内掺衍生物M@C₂₂(M=Sc,Ti,V,Cr,Mn,Fe,Co和Ni)的几何结构和电子结构进行计算研究.发现非典型富勒烯C₂₂的基态结构是含有一个四碳环的单重态笼状结构.过渡金属原子的掺入明显提高了体系的稳定性. C-M键既有一定共价性又有一定离子性.磁性、能级图、轨道分布和态密度图分析表明: M原子的3d轨道和碳笼的C原子的原子轨道之间存在较强的轨道杂化. Ti, Cr, Fe和Ni内掺的结构出现磁性完全猝灭现象. Sc和碳笼间是弱反铁磁作用, V,Mn和Co与碳笼间是弱铁磁作用.     

Density functional theory study on LaNi4.5Al0.5 hydride phase： electronic properties and sites occupation＊

In this paper the crystal structure, electronic structure and hydrogen site occupation of LaNi4.5Al0.5Hy hydride phase （y = 5.0, 6.0） have been investigated by using full-potential linearized augmented plane wave method. The hydrogen atoms were found to prefer the 6m, 12o and 12n sites, while no 4h sites were occupied. A narrowed Ni-d band is found due to the lattice expansion, the total density of states at EF increases with y, which indicates that the compounds become less stable. The interaction between Al and Ni, H plays a dominant role in the stability of LaNi4.5Al0.5 hydride phase. The smaller the shift of EF towards the higher energy region, the more stable the compounds will be. The obtained results are compared with experimental data and discussed in the light of previous works.     

Production of ultrafine particles of high-temperature tetragonal WO<Subscript>3</Subscript> by dc arc discharge in Ar–O<Subscript>2</Subscript> gases

Ultrafine particles of WO₃ are successfully produced by dc arc discharge in Ar-O₂ gases. Particle sizes are distributed from 10 nm to 1 m depending on production conditions: gas pressure, collection position and discharge current. Observations of the cooled particles by electron microscopy indicate that the WO₃ particles are tetragonal, a phase that is usually only stable above 725 °C. The octahedral crystals are bounded by eight {1 0 1} faces and occasionally truncated by {1 0 0} and/or {0 0 1} faces. This method of producing WO₃ by dc arc discharge therefore affords a high-temperature phase that is preserved upon cooling to room temperature.