快速响应大孔聚(N-异丙基丙烯酰胺-co-丙烯酸)水凝胶的合成及表征

以聚乙二醇6000为成孔剂,由自由基引发N-异丙基丙烯酰胺(NIPA)和丙烯酸(AAc)共聚交联得到大孔凝胶,研究了凝胶对环境温度的响应性能.在凝胶制备过程中,PEG6000分子充当成孔剂,得到的凝胶具有大孔结构.这种大孔结构有利于水分子的进出,大孔凝胶对温度变化有较快的响应速率.增加亲水单体AAc的含量,凝胶的LCST有所升高,凝胶的亲水性增强,在较低温度下凝胶的溶胀率也随之升高.振荡实验表明,所得的大孔凝胶具有反复使用的能力.     

大孔PAMPS/PVA半互穿网络型水凝胶的制备及其性能研究

以PEG6000为成孔剂, 合成了大孔聚(2-丙烯酰胺-2-甲基丙磺酸)/聚乙烯醇半互穿网络型(s-IPN)水凝胶. 红外分析表明, PVA与PAMPS之间形成了较强的氢键, 使得PVA分子上的C—O伸缩振动吸收峰移向了低波数处. X射线衍射分析发现, 当PVA用量较高时, 由于部分的PVA结晶, 使得凝胶的半互穿网络结构不均匀. 电镜分析结果表明, 没有使用成孔剂的凝胶表面成褶皱形, 不存在任何孔洞结构; 而以PEG6000为成孔剂的凝胶表面存在相互贯穿的大孔结构. 研究了该水凝胶的溶胀性能, 结果表明, 该水凝胶的平衡溶胀度在116至320之间; 而成孔剂PEG6000的加入能较大幅度提高凝胶的溶胀速率, 凝胶在240 min之内就能达到溶胀平衡. 对凝胶抗压缩性能的研究表明, 当PVA用量为9.1% (w)时, 凝胶的抗压缩强度最大, 可达12.0 MPa; 而成孔剂的加入会在一定程度削弱凝胶的抗压缩强度. 该凝胶具有较好的电场敏感性, 研究发现, 将吸去离子水达到溶胀平衡的凝胶放入施加有电场的0.2 mol•L－1 NaCl溶液中时, 凝胶迅速偏向阳极. 而PVA和成孔剂PGE6000的用量均对凝胶的偏转速度以及最大偏转角存在较大的影响.     

聚(2-丙烯酰胺基-2-甲基丙磺酸/丙烯酰胺)水凝胶合成与性能研究

以2-丙烯酰胺基-2-甲基丙磺酸和丙烯酰胺为原料,以PEG6000为成孔剂,采用水溶液法合成多孔性聚(2-丙烯酰胺基-2-甲基丙磺酸/丙烯酰胺)水凝胶,研究了凝胶的溶胀性和电场作用下的退溶胀性能.在凝胶制备过程中,PEG6000分子充当成孔剂,通过综合性能比较和红外光谱测试可知,所得凝胶具有多孔结构,这种孔洞结构有利于水分子的进出.结果显示,当引发剂为0.005 mol/L,交联剂为0.008 mol/L,摩尔比AMPS:PEG6000=100∶1,AMPS:AAm=2∶1时,可得综合性能较好的PAMA凝胶.     

自支撑海藻酸钙水凝胶抗污染过滤膜的制备及截留性能

以聚乙二醇(PEG)为致孔剂制备了自支撑海藻酸钙(CA)水凝胶过滤膜.通过数码照片及扫描电镜观察膜的表面形貌,探讨了膜的力学性能的压缩率、通量与压力的关系.研究了海藻酸钠浓度、致孔剂浓度对纯水通量和溶菌酶(Lyz)截留性能的影响.结果表明,海藻酸钠浓度越低,PEG浓度越高,膜的通量越大,压缩率也越大.膜通量随着跨膜压力的增加呈现先上升后稳定的趋势.Lyz和牛血清蛋白(BSA)溶液的稳定通量分别为纯水通量的89.97%和94.6%,表明海藻酸钙水凝胶过滤膜具有良好的抗蛋白质污染性能.膜对乳化油的过滤通量为纯水通量的93.04%,且截留率高达99.85%.对于不同分子量PEG的截留结果表明,当PEG分子量大于致孔剂的分子量时,截留率达到90%以上.以低分子量PEG400为致孔剂制备的水凝胶过滤膜对染料亮蓝的截留率达到99.75%,表明该水凝胶膜具有作为纳滤膜的前景.     

多孔聚N-异丙基丙烯酰胺水凝胶的制备与缓释性能

以N-异丙基丙烯酰胺(NIPA)、N,N-亚甲基双丙烯酰胺(MBA)和聚乙二醇(PEG)为原料,以60Co-γ射线为放射源制备了快速响应聚N-异丙基丙烯酰胺(PNIPA)多孔水凝胶。用红外光谱分析了水凝胶的结构,并测定了水凝胶的溶胀动力学、退溶胀动力学和平衡溶胀率。结果表明,PEG分子仅在聚合交联过程中充当成孔剂,不参与反应,反应后可被除去;水凝胶具有明显的温度敏感性,成孔剂的添加提高了水凝胶的溶胀性能和LCST。选用阿司匹林为模型药物,对水凝胶的药物缓释性能进行了初步研究。     

一种快速响应电场敏感多孔水凝胶的合成及其性能研究

以4-乙酰基丙烯酰乙酸乙酯(AAEA)、2-丙烯酰胺基-2-甲基-1-丙磺酸(AMPS)为单体,不同分子量的聚乙二醇(PEG)为成孔剂,通过自由基溶液聚合法,合成了新型多孔快速响应电场敏感性水凝胶.结果表明,成孔剂PEG被洗脱后在凝胶内部形成了互相贯穿的孔洞结构,孔径在30～120μm之间.以PEG6000为成孔剂致孔后的多孔凝胶溶胀速率和消溶胀速率最快,在去离子水中30s达到溶胀平衡,在0.1mol/L的NaCl溶液中40min达到消溶胀平衡;电场作用下凝胶的消溶胀速度大大加快,12min内即可达到平衡.凝胶中AMPS含量的增多会加快凝胶在电场中的响应速度;而高温下,随着AAEA含量的增加,凝胶内部疏水基团增多并收缩产生大量的疏水微区,限制了凝胶内部水分的持续排出,因此n(AAEA)∶n(AMPS)=3∶1的凝胶4min内即可排出表面水分达到消溶胀平衡,可保水率却高达75%.同时,增大电解液的pH值、浓度以及提高电解电压,均会加快凝胶的消溶胀行为.     

快速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶 Ⅰ.以CaCO_3为成孔剂制备方法、表征及动力学研究

以不同粒径的CaCO3粒子为成孔剂 ,合成了快速响应的温敏性聚 (N 异丙基丙烯酰胺 ) (PNIPA)水凝胶 .利用扫描电镜观察到水凝胶具有特殊的孔状结构 ,得到水凝胶的孔径大小为几十微米左右 .动力学研究表明 ,该水凝胶在温敏膨胀或收缩时 ,具有快速的响应速率 ,在 10min内的失水率可达 90 % .比较了干凝胶和4 0℃下失水后的凝胶两种不同状态下水凝胶的膨胀曲线 ,发现两者的溶胀动力学曲线明显不同 ,前者的曲线有拐点 .同时发现与失水收缩速率相比 ,水凝胶具有较慢的吸水膨胀速率 .     

聚乳酸-聚乙二醇-聚乳酸三嵌段共聚物的降解性能

以辛酸亚锡为引发剂,聚乙二醇大分子为共引发剂进行现交酯开环聚合,制备了系列聚乳酸（PLA）－聚乙二醇（PEG）－聚乳酸（PLA）三嵌段共聚物。从共聚物在生理盐水 中降解时特性粘度[η],质量和热行为的变化,考察了PEG分子量和丙交酯／PEG（摩尔比）对共聚物降解行为的影响,结果表明,PEG嵌段对共聚物的降解速率有重要影响,丙交酯／PEG一定时,PEG分子量越大,共聚物越容易降解,PEG嵌段长度一定时,丙交酯／PEG越大,共聚物降解速率越小。     

速响应的温敏性聚(N-异丙基丙烯酰胺)水凝胶Ⅰ.以CaCO3为成孔剂制备方法、表征及动力学研究

以不同粒径的CaCO3粒子为成孔剂,合成了快速响应的温敏性聚(N-异丙基丙烯酰胺)(PNIPA)水凝胶.利用扫描电镜观察到水凝胶具有特殊的孔状结构,得到水凝胶的孔径大小为几十微米左右.动力学研究表明,该水凝胶在温敏膨胀或收缩时,具有快速的响应速率,在10 min内的失水率可达90%.比较了干凝胶和40℃下失水后的凝胶两种不同状态下水凝胶的膨胀曲线,发现两者的溶胀动力学曲线明显不同,前者的曲线有拐点.同时发现与失水收缩速率相比,水凝胶具有较慢的吸水膨胀速率.     

聚乙二醇/甲基丙烯酸β羟乙酯水凝胶的合成及其表征

以偶氮二异丁腈(AIBN)为引发剂,N,N'-亚甲基双丙烯酰胺(BIS)为交联剂,采用自由基聚合法合成了聚乙二醇(PEG)/甲基丙烯酸β-羟乙酯(HEMA)水凝胶.应用傅立叶转换红外光谱(FT-IR)研究了水凝胶分子间的相互作用,结果表明PEG和HEMA间存在较强的分子闻氢键.     

Macroporous Poly(Acrylamide) Hydrogels: Swelling and Shrinking Behaviors

Macroporous poly(acrylamide) hydrogels have been synthesized by using poly(ethylene glycol) (PEG) with three different molecular weights as the pore‐forming agent. Scanning electron microscope graphs reveal that the macroporous network structure of the hydrogels can be adjusted by applying different molecular weights of PEG during the polymerization reaction. The swelling ratios of the PEG‐modified hydrogels were much higher than those for the same type of hydrogel prepared via conventional method. However, the swelling/deswelling ratios of the PEG‐modified hydrogels were affected slightly by the change in the amount of the PEG. Scanning electron microscopy experiments, together with swelling ratio studies, reveal that the PEG‐modified hydrogels are characterized by an open structure with more pores and higher swelling ratio, but lower mechanical strength, compared the conventional hydrogel. PAAm has potential applications in controlled release of macromolecular active agents.     

聚乙二醇对PAMPS/PAM双网络水凝胶性能的影响

采用紫外光引发聚合制备了聚乙二醇(PEG)改性的聚(2-丙烯酰胺-2-甲基丙磺酸)/聚丙烯酰胺(PAMPS/PAM)双网络水凝胶.测定并比较了PEG改性前后双网络水凝胶的溶胀动力学以及单网络水凝胶中丙烯酰胺(AM)的吸收量;用扫描电子显微镜(SEM)观察了单网络水凝胶的结构;测定PEG改性前后双网络水凝胶的压缩及拉伸性能.结果表明,经PEG改性后的双网络水凝胶有较高的溶胀比;改性后单网络水凝胶更易吸收AM;改性后双网络水凝胶压缩形变率达到90%以上、拉伸形变率是未改性双网络水凝胶的2倍.     

Effect of Pore-Forming Agent Type on Swelling Properties of Macroporous Poly(N-[3-(dimethylaminopropyl)]-methacrylamide-co-acrylamide) Hydrogels

Macroporous poly(N-[3-(dimethylaminopropyl)]methacrylamide-co-acrylamide) [P(DMAPMA-co-AAm)] hydrogels were prepared by free-radical crosslinking copolymerization of corresponding monomers in water using two different pore-forming agents such as hydroxypropyl celluose (HPC) and poly(ethylene glycol) (PEG). The effect of these pore-forming agents on the volume phase transition temperature (VPT-T), interior morphology and swelling/deswelling kinetics of the P(DMAPMA-co-AAm) hydrogels was investigated. Scanning electron micrographs revealed that the interior network structure of the hydrogel matrix became more porous due to the presence of HPC or PEG pore-forming agents. The more porous matrix provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external stimuli. Particularly, due to its unique macroporous structure, the PEG-modified hydrogel showed a tremendously faster response to the external temperature changes during deswelling process and the swelling process at 22°C.     

Preparation and characterization of macroporous poly(N‐isopropylacrylamide) hydrogels for the controlled release of proteins

Macroporous, temperature‐sensitive poly(N‐isopropylacrylamide) (PNIPAAm) hydrogels were synthesized with poly(ethylene glycol)s (PEGs; molecular weight = 2000–6000) as the pore‐forming agents. The influence of the molecular weight and PEG content on the responsive kinetics of these macroporous hydrogels was investigated. The PEG‐modified PNIPAAm hydrogels were characterized by the swelling ratio, deswelling–reswelling kinetics, Fourier transform infrared, and differential scanning calorimetry. The morphology of these hydrogels was analyzed with scanning electron microscopy. The prepared macroporous hydrogels exhibited some unique properties in comparison with the gels with low molecular weight PEGs (molecular weight < 2000) as the pore‐forming agents. In addition, a preliminary study on the controlled release of bovine serum albumin from these macroporous hydrogels was carried out. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 152–159, 2003     

NIPAM共聚物多孔水凝胶的光引发RAFT合成及其溶胀性能

采用光引发可逆加成-断裂链转移(RAFT)方法,在室温下先合成了链端含有三硫代碳酸酯基的大分子链转移剂聚(N,N'-二甲基丙烯酰胺)(PDMAM),然后与N-异丙基丙烯酰胺(NIPAM)、N,N'-二甲基双丙烯酰胺(BIS)交联共聚合,并通过聚乙二醇的制孔作用制得PNIPAM-g-PDMAM梳型/多孔水凝胶.采用FTI...     

聚对二氧环己酮/聚乙二醇两亲性聚合物共网络的合成与表征

以辛酸亚锡为催化剂,季戊四醇(PTOL)为引发剂,引发对二氧环己酮(PDO)单体开环聚合,合成了以PTOL为核的四臂聚对二氧环己酮(4s-PPDO).通过直接将4s-PPDO预聚物和聚乙二醇(PEG)于熔点以上、惰性气体保护下与偶联剂甲苯二异氰酸酯(TDI)交联共聚得到聚对二氧环己酮/聚乙二醇(PPDO-b-PEG)两亲性共网络聚合物(PPDO-PEG APCNs).研究了两亲性聚合物共网络结构、配比组成、溶剂种类等对聚合物溶胀率的影响,结果表明APCNs在不同类型的溶剂中表现出不同的溶胀行为,可以通过调节偶联剂的用量及PPDO/PEG的投料比来满足不同的实际需求.通过示差扫描量热分析(DSC)详细研究APCNs的结晶性能,证实交联反应降低APCNs的结晶度和结晶尺寸.     

Rheological behaviour of irradiated wound dressing poly(vinyl pyrrolidone) hydrogels

The use of hydrogels as biomaterials has increased lately. Poly(vinyl pyrrolidone) (PVP) is an example of polymer hydrogels applied for the synthesis of hydrogel to be used in different biomedical applications. This paper describes a study on rheological properties of PVP hydrogels obtained by gamma radiation techniques. PVP hydrogels were obtained by gamma radiation of PVP water solutions with different radiation doses. It was studied the influence of additives such as poly(ethylene glycol) (PEG), poly(ethylene oxide) (PEO) and glycerol on the rheological behaviour of the gel. The rheological behaviour of hydrogel samples was characterized by measuring the shear storage modulus (G′) under dynamic shear loading. Besides this, sterility and cytotoxicity tests were performed. The study on rheological behaviour of hydrogels showed that G′ of PVP gels change according to the additive used. Glycerol increases the fluidity of the gel. The influence of PEG depends on the amount and on its molecular mass. The increase on PEG amount and molecular mass cause a decrease of G′ and an increase in the crosslinking density of PVP hydrogel network. The use of high molecular weight PEO allows the increase of the elasticity of the PVP gels.     

Investigation of swelling and network parameters of poly(ethylene glycol)-crosslinked poly(methyl vinyl ether-co-maleic acid) hydrogels

The influence of poly(ethylene glycol) (PEG) plasticiser content and molecular weight on the physicochemical properties of films cast from aqueous blends of poly(methyl vinyl ether-co-maleic acid) was investigated using thermal analysis, swelling studies, scanning electron microscopy (SEM) and attenuated total reflectance (ATR)-Fourier transform infrared (FTIR) spectroscopy. FTIR spectroscopy revealed a shift of the CO peak from 1708 to 1731 cm⁻¹, indicating that an esterification reaction had occurred upon heating, thus producing crosslinked films. Higher molecular weight PEGs (10,000 and 1000 Da, respectively), having greater chain length, producing hydrogel networks with lower crosslink densities and higher average molecular weight between two consecutive crosslinks. Accordingly, such materials exhibited higher swelling rates. Hydrogels crosslinked with a low molecular weight PEG (PEG 200) showed rigid networks with high crosslink densities and, therefore, lower swelling rates. Polymer:plasticizer ratio alteration did not yield any discernable patterns, regardless of the method of analysis. The polymer-water interaction parameter (χ) increased with increases in the crosslink density. SEM studies showed that porosity of the crosslinked films increased with increasing PEG MW, confirming what had been observed with swelling studies and thermal analysis, that the crosslink density must be decreased as the M_w of the crosslinker is increased. Hydrogels containing PMVE/MA/PEG 10,000 could be used for rapid delivery of drug, due to their low crosslink density. Moderately crosslinked PMVE/MA/PEG 1000 hydrogels or highly crosslinked PMVE/MA/PEG 200 systems could then be used in controlling the drug delivery rates. We are currently evaluating these systems, both alone and in combination, for use in sustained release drug delivery devices.     

聚乙烯醇水凝胶溶胀特性研究

在前文对聚乙烯醇水溶液冰冻凝胶化浓度依赖性研究基础上，对接触浓度（Ｃ）以上聚乙烯醇水溶液通过冰冻－融化处理，制得了一种含水率高达９５～９８％的水凝胶．系统研究了该水凝胶在蒸馏水中的溶胀及溶解特性．得到了一个与实验结果相吻合的溶胀动力学方程：Ｑ１＝Ｑｅ－（Ｑｅ－ＱＯ）／ｅｋｔ，及平衡溶胀比Ｑｅ与浓度之间的定量关系：Ｑｅ＝６０．３－４．４５×１０２Ｃ．发现当冰冻－融化次数Ｎ≤５时，平衡溶胀比Ｑｅ及溶解量Ｗ与冰冻－融化次数（Ｎ）间满足幂函数关系：Ｑｅ。Ｗ通过对聚乙烯醇水凝胶平衡溶胀比与经冰冻处理的聚乙烯醇水溶液特性粘数进行比较，发现反映链间氢键凝聚缠结效应与反映链内氢键凝聚缠结效应的定量指标具有等效性．     

Thermosensitive poly(N-isopropylacrylamide-co-acrylamide) hydrogels: Synthesis, swelling and interaction with ionic surfactants

Thermosensitive hydrogels were prepared by free-radical polymerization in aqueous solution from N-isopropylacrylamide (NIPA) and acrylamide (AAm) monomers. N,N-Methylenebis(acrylamide) (MBAAm) was used as a crosslinker. A kinetic study of the absorption determined the transport mechanism. The diffusion coefficients of these hydrogels were calculated for the Fickian mechanism. It was shown that the swelling behavior of the P(NIPA-co-AAm) hydrogels can be controlled by changing the amount of MBAAm. The swelling equilibrium of the P(NIPA-co-AAm) hydrogels was also investigated as a function of temperature in aqueous solutions of the anionic surfactant sodium dodecyl sulfate (SDS) and the cationic surfactant dodecyltrimethylammonium bromide (DTAB). In SDS and DTAB solutions, the equilibrium swelling ratio of the hydrogels increased, this is ascribed to the conversion of non-ionic P(NIPA-co-AAm) hydrogel into polyelectrolyte hydrogels due to binding of surfactant molecules through the hydrophobic interaction. Additionally, the amount of free SDS and DTAB ions was measured at different temperatures by a conductometric method, it was found that the electric conductivity of the P(NIPA-co-AAm)—surfactant systems depended strongly on both the type and concentration of surfactant solutions.