重油催化裂化汽油中含硫化合物的分析

 采用气相法 ,分别利用火焰光度检测器 (FPD)和原子发射检测器 (AED)对中国石化北京燕山石油化工公司 (简称燕化 )炼油厂和石家庄炼油厂生产的重油催化裂化 (RFCC)汽油中的硫化物进行了分析。燕化炼油厂RFCC汽油中总硫只有 2 9 5mg/L ,采用FPD无法检测 ;石家庄炼油厂的RFCC汽油中总硫为 72 0 1mg/L。用标样和气相 质谱法 (GC MS)定性 ,FPD分离检测出 19种硫化物 ,主要是硫醇、噻吩类硫化物 ,硫醚类硫化物和二硫化物均未检出。用AED鉴定出燕化炼油厂RFCC汽油中的硫化物 12种 ,主要是噻吩和四氢噻吩类、低碳硫醇和二硫化物。     

Fast analysis of oxygen and sulfur compounds in gasoline by GC-AED

This paper describes a method for determining both the total sulfur content and the concentration of oxygenated additives in gasoline by gas chromatography with atomic emission detection (GC-AED). The AED provides selective detection of oxygen and sulfur compounds. Because the response factors for sulfur and oxygen are largely independent of the type of compound, calibration and determination of total element content are simplified. The use of a 0.1 mm i.d. capillary column enables complete elution of the components of the gasoline in under 10 minutes.     

催化裂化汽油中硫化物的气相色谱-原子发射光谱分析方法及应用

采用气相色谱-原子发射光谱联用(GC-AED)技术，建立了催化裂化汽油中各种硫化物类型分布的分析方法。考察了色谱条件对催化汽油中各种硫化物分离的影响，定性了催化汽油中的60余种硫化物，首次计算了程序升温条件下汽油馏分中各种硫化物的保留指数，为不同实验室的定性比较提供了依据。该方法可应用于不同来源汽油中各种硫化物类型分布的研究。     

催化裂化汽油中硫化物类型分布的气相色谱-硫化学发光检测的方法研究

采用气相色谱-硫化学发光检测器(GC-SCD),建立了催化裂化汽油(FCC汽油)中各种硫化物类型分布的分析方法。考察了色谱条件对催化裂化汽油中各种硫化物分离的影响,定性了某催化裂化汽油中的58个硫化物。采用该方法,硫化物中的硫在其质量浓度为0.5~800.0 mg/L时,其峰面积与质量浓度呈较好的线性关系,相关系数达0.999,其响应与硫化物的类型无关。FCC汽油中几种主要硫化物(噻吩、正丁硫醇、2-甲基噻吩、3-甲基噻吩、2,4-二甲基噻吩)的浓度测定值的相对标准偏差(RSD)均小于5.0%。当信噪     

Flow injection gas chromatography with sulfur chemiluminescence detection for the analysis of total sulfur in complex hydrocarbon matrixes

A fast and reliable analytical technique for the determination of total sulfur levels in complex hydrocarbon matrices is introduced. The method employed flow injection technique using a gas chromatograph as a sample introduction device and a gas phase dual‐plasma sulfur chemiluminescence detector for sulfur quantification. Using the technique described, total sulfur measurement in challenging hydrocarbon matrices can be achieved in less than 10 s with sample‐to‐sample time <2 min. The high degree of selectivity and sensitivity toward sulfur compounds of the detector offers the ability to measure low sulfur levels with a detection limit in the range of 20 ppb w/w S. The equimolar response characteristic of the detector allows the quantitation of unknown sulfur compounds and simplifies the calibration process. Response is linear over a concentration range of five orders of magnitude, with a high degree of repeatability. The detector's lack of response to hydrocarbons enables direct analysis without the need for time‐consuming sample preparation and chromatographic separation processes. This flow injection‐based sulfur chemiluminescence detection technique is ideal for fast analysis or trace sulfur analysis.     

Determination of the sulfur components of gasoline streams by capillary column gas chromatography with sulfur chemiluminescence detection

A method using a sulfur chemiluminescence detector (SCD) has been developed for the qualitative and quantitative determination of sulfur components in stabilized gasoline-range process streams, including blended gasolines containing between 1 and > 4000 ppm total sulfur. The detection limit per sulfur component was approximately 50 ppb. On-column injection was employed for optimum precision and accuracy. A new probe material was found which did not soften under FID operating conditions. A new method, using a hydrogen sulfide permeation tube, was developed for rapid alignment of the probe in the FID.     

汽油中有机硫化物的酸富集和结构分析

石油中发现的硫化物已超过250种，其中约有1／4存在于汽油中。由于汽油中每种硫化物的含量都很低，又有十分复杂的烃组分和含氮组分的干扰，单纯使用仪器方法对汽油中的有机硫化物进行结构分析是十分困难的。通常的做法是对汽油样品进行预处理，使硫化物从混合烃体系中分离出来，再通过仪器和相应标样进行类型分析或结构鉴定。目前研究者在此方面做了很多工作，花瑞香等用29种硫化物标样，采取GC／SCD辅以选择性化学反应对汽油馏分的硫化物形态分布研究。     

Rapid determination of total sulfur in fuels using gas chromatography with atomic emission detection

The purpose of this study is to determine whether gas chromatography (GC)-atomic emission detection (AED) can be used in a low-resolution mode for rapid, accurate determinations of total sulfur in fuels at trace levels to complement other popular methods of total sulfur analysis. A method for the rapid determination of total sulfur in fuels (called "fast GC-AED") is developed. The method is tested on gasoline, jet fuel, kerosene, and diesel fuel with sulfur concentrations ranging from 125 mg/L down to 2.5 mg/L. Fast GC-AED shows better performance than traditional GC-AED for total sulfur determinations, especially for complex mixtures containing many different sulfur-containing compounds at trace levels. This method also shows that GC-AED can be used for both rapid determinations of total sulfur and traditional determinations of speciated sulfur without requiring equipment changes. Fast GC-AED is competitive with other popular methods for sulfur analysis. The 5-min program that is developed for fast GC-AED is comparable with the time scale of other methods, such as wavelength dispersive X-ray fluorescence and UV-fluorescence (2 to 5 min). Fast GC-AED also compares favorably with UV-fluorescence for trace sulfur determinations, demonstrating accuracy down to 2.5-mg/L sulfur.     

High-efficiency process for production of sulfur from metallurgical sulfur dioxide gases

Process in which sulfur is produced from a gas containing 25–55% SO₂ was studied in order to evaluate the real efficiency of the catalytic post-reduction of sulfur dioxide in a pilot unit with gas flow rate of up to 1.2 nm³ h^–1 at the following temperatures (°C): thermal stage 850–1100, catalytic conversion 350–570, and Claus reactor 219–279. It was found that the conversion at 400–550°C and space velocity of 1600 h^–1 on AOK-78-57 promoted aluminum oxide catalyst provides full processing of organosulfur compounds (CS₂ and COS). The temperature dependence of the conversion/generation of hydrogen sulfide on AOK-78-57 catalyst corresponds to the equilibrium model. It was experimentally confirmed that the homogeneous reduction of sulfur dioxide gas with methane at T ≈ 1100°C, with catalytic post-reduction at 400–550°C and subsequent Claus-conversion of the reduced gas at 230–260°C, provide a sufficiently deep (by 92–95%) general processing of sulfur dioxide gas to sulfur.     

Analysis of atmospheric sulfur gases by capillary gas chromatography with atomic emission detection

The atomic emission detector (AED) has been found to be a sensitive and selective instrument for analysis of atmospheric sulfur gases by capillary gas chromatography. It was possible to determine atmospheric dimethyl sulfide at concentrations below 0.3 nmol/m³ typical of the remote marine environment in winter. Sample analyses from the Australian Baseline Air Pollution Station, Cape Grim, are used to illustrate this. In comparison with other sulfur-specific detectors previously used for this work, the AED has been found to exhibit the best combination of specificity and sensitivity. A configuration comprising a series of valves, gas calibration loops, and a cryogenic trap prior to the GC-AED was used for sample analysis. Standard addition of sulfur hexafluoride was found to assist determination of carbonyl sulfide, as it could be used to take into account the magnitude of signal quenching from coeluting gases. The AED was also found to be a selective detector for the direct injection of water-soluble dimethyl sulfide oxidation products.     

溴加成脱烯反应用于含烯汽油单体烃及族组成的分析

 提出了一种用于汽油组成分析的新方法 ,该方法采用溴加成选择性地转化并检测烯烃 ,解决了单体烃分析中的烷烯混峰问题 ,简化了识谱过程 ,由此通过一个包含极性预柱与非极性分析柱的简单二维体系或者与气相仪 (GC)联用的原子发射光谱检测器 (AED)两种途径均可进行准确度高的单体烃分析。在所选溴加成条件下 ,汽油中烯烃溴化率为 10 0 % ,而烷烃和芳烃保持惰性。处理全过程仅需 12 0s～ 15 0s ,操作简单且重复性好。该处理适用于含烯量为 0～ 10 0 % (体积分数 )的汽油 ,且主要针对含烯较高的催化裂化汽油。     

Deep hydrodesulfurization of FCC gasoline and gas oil cuts: Comparison of CO effect,a by-product from biomass

Regarding the composition of the various feedstocks which should be hydrotreated in order to obtain fuels with amount of sulfur less than 10 wt ppm, we have shown that the presence of traces of CO, a by-product from lignocellulosic biomass feedstock conversion, inhibited the transformation of model compounds representative of FCC gasolines and gas oils over CoMo-based sulfide catalysts. Thus, this effect is more significant in the presence of 2-methylthiophene and 2,3-dimethylbut-2-ene representative of a FCC gasoline than in the presence of dibenzothiophene and 4,6-dimethyldibenzothiophene representative of a straight run gas oil, even if the operating conditions are not the same. This effect is attributed to phenomena of competitive adsorption between sulfur compounds, alkenes and CO on the catalyst surface.     

催化裂化汽油中含硫化合物的分离氧化脱硫研究

以负载氧化铜的氧化铝层析柱对催化裂化(FCC)汽油全馏分进行分离,使其中的烷烃、烯烃与芳烃、含硫化合物分离成极性不同的两组,含硫化合物在芳烃组分中得以分离富集。分离后对芳烃组分中的含硫化合物进行氧化,脱硫率达72%。氧化后的芳烃组分与分离出来的烷烃、烯烃组分混兑,可使FCC汽油的总脱硫率达71·3%。     

汽油馏分的硫化物形态分布研究

采用气相色谱和硫化学发光检测(GC-SCD)技术,经过对色谱条件的优化,建立了汽油馏分中硫化物形态分布的测定方法。用标准物质的保留时间辅以化学法脱除硫醇、硫醚的方法对107个硫化物进行了定性;标准硫化物保留时间重复测定结果的相对标准偏差(RSD)≤0.25%。用内标法对主要的硫化物和总硫含量进行了定量,方法的加标回收率为96%~115%;同一样品重复测定5次,含硫大于7 mg/kg的硫化物组分重复测定结果的RSD≤8.9%。所建立的方法可用于不同装置的汽油馏分的硫化物形态分布规律的研究。     

FCC汽油GS中硫化物的分布特点

FCC汽油样品GS按沸点切割成六个组分，然后使用配有原子发射光谱检测器的气相色谱仪（GC/AED）分别分析每个馏分样品中的含硫化合物。数据表明，样品中含硫化合物以噻吩和烷基取代噻吩类为主，而且含硫化合物在样品中的分布是不均匀的，随着切割段沸点的提高，含硫化合物含量明显增加，多碳数取代噻吩类化合物含量增加。数据还可以用来参考确定轻、重馏分油切割点，以对轻、重馏分油采取不同的脱硫方法，达到最佳经济效益。     

Column selection and optimization for sulfur compound analyses by gas chromatography

The analysis of sulfur-containing compounds using fused silica capillary columns and the Sulfur Chemiluminescence Detector has been investigated. This combination of an inert chromatographic system and a high sensitivity, selective detector provides significant advantages for the analysis of low levels of sulfur compounds in complex matrices over existing techniques. Capillary columns coated with thick films (1–4 μm) of methyl silicone stationary phase permit separation of most sulfur containing compounds and, when used with sub-ambient column temperatures, these columns can be used for the separation of sulfur gases. The effects of stationary film thickness, column length, and internal diameter for the measurement of sulfur compounds in hydrocarbon matrices has been determined.     

Identification of control parameters for the sulfur gas storability with bag sampling methods

Air samples containing sulfur compounds are often collected and stored in sample bags prior to analysis. The storage stability of six gaseous sulfur compounds (H₂S, CH₃SH, DMS, CS₂, DMDS and SO₂) was compared between two different bag materials (polyvinyl fluoride (PVF) and polyester aluminum (PEA)) at five initial concentrations (1, 10, 100, 1000, and 10,000 ppb). The response factors (RF) of these samples were determined after storage periods of 0, 1, and 3 days by gas chromatography–pulsed flame photometric detector (GC–PFPD) combined with an air server (AS)/thermal desorber (TD) system. Although concentration reduction occurred more rapidly from samples of the high concentration standards (1000 and 10,000 ppb), such trends were not evident in their low concentration counterparts (1, 10, and 100 ppb). As such, temporal changes in RF values and the associated loss rates of most sulfur gases were greatly affected by their initial concentration levels. Moreover, the storability of oxidized sulfur compound (SO₂) was greatly distinguished from that of reduced sulfur compounds (RSCs), as the former almost disappeared in the PVF bag even after one day. The results of our study confirm that storability of gaseous sulfur species is affected interactively by such variables as initial gas concentration level, bag material type, and oxidation status with the associated reactivity.     

气相色谱-氮化学发光检测法分析催化汽油中含氮化合物类型的分布

建立了催化汽油馏分中各种含氮化合物类型分布的气相色谱-氮化学发光检测分析方法,考察了各种色谱条件对含氮化合物分离的影响。采用化学预处理的方法浓缩了催化汽油中的含氮化合物,并结合气相色谱-质谱检测以及部分含氮化合物标准样品,对某催化汽油中的20多个含氮化合物进行了定性(或归类)。催化汽油中几种主要含氮化合物(苯胺、2-甲基苯胺、二甲基苯胺)含量测定值的相对标准偏差(RSD)均不大于2.5%。当信噪比(S/N)为3时,苯胺氮的检出限为1.0 mg/L。该方法可用于不同来源和不同加工工艺的汽油馏分中各种含氮化合物类型分布的研究。     

提高USY型FCC催化剂硫转移和催化裂化活性的研究

采用镁、铈、镧和磷对USY型FCC催化剂进行改性，采用FT IR分析方法对改性催化剂的表面酸性进行了表征，研究了硫转移活性组分对催化剂的硫转移和催化裂化活性的影响。结果表明，多次氧化 还原循环后，改性催化剂仍保持较好的硫转移活性，可以达到60%以上。镁的引入会减少基质和分子筛表面强酸的数量，少量镁的引入对催化裂化活性影响不大，铈和镧的引入会使分子筛和基质的表面酸量得到显著增加，提高催化裂化活性，但同时会引起焦炭的增加，磷改性可改善基质和分子筛表面酸性，抑制焦炭的产生，保持催化裂化活性的同时使汽油中的烯烃质量分数下降6%。     

Characterization of gasolines using on-line multidimensional supercritical fluid chromatography/ capillary gas chromatography

Summary Using packed column supercritical fluid chromatography on-line with capillary gas chromatography, gasolines have been characterized with respect to the separation of hydrocarbon classes as a group as well as a detailed fingerprinting of individual components within the classes. Using selective heartcutting, specific gasoline peaks were transferred to the capillary gas chromatograph as they eluted from the supercritical fluid chromatograph. Quantitative information was collected simultaneously from the flame ionization detectors that were used on both chromatographs. This report will describe the operational chromatographic conditions that were used for gasoline separations as well as provide results of quantitative heartcut reproducibility experiments of gasolines and hydrocarbon standards.

---

Charakterisierung von Benzinen durch on-line-Kombination von multidimensionaler Chromatographie mit überkritischen fluiden Phasen und Capillar-Gas-Chromatographie