液体物性对雾化射流液雾粒径的影响

对不同液体在空气中湍动雾化射流的气液两相流场进行了数值模拟.建立了一次雾化的一维模型,分析了粘度、表面张力和气液质量流量比对液雾粒径的影响趋势,采用基于粒子追踪法的二次雾化三维模型,分析了物性和各种工况对液雾粒径沿轴向分布的影响程度.计算结果和已公开发表的实验数据进行比对,得到了较好的吻合,在此基础上,分析了影响气泡雾化喷嘴雾化质量的主要因素.     

不同工况下旋流液雾燃烧的直接数值模拟

采用有限差分方法对不同工况下三维旋流液雾燃烧进行了直接数值模拟,其中液滴的跟踪在拉格朗日框架中进行,液滴的蒸发相变采用无限热传导蒸发模型描述,气相燃烧采用自适应单步反应机理,模拟中采用的模型燃烧器尽可能逼近真实的燃气轮机旋流燃烧器.结果发现,旋流液雾燃烧流动和火焰结构受到旋流方式和当量比的影响,流场中出现了反平行排列的...     

气液两相流体绕方柱流动的数值模拟

本文详细给出了气液两相流动双流体模型下的各控制方程组和相间作用力,通过将气泡引起的紊流与剪切引起的紊流线性叠加给出了气液两相流动的紊流模型。通过给出的边界条件,采用ＩＴＡ－ＩＰＳＡ算法对垂直上升的气液两相流横向冲刷方柱引起漩涡证替脱落的过程进行了数值模拟,得到了流场和局部含气率变化的示意图,数值模拟与试验的结果基本一致。     

叶片式混输泵内气液两相流的数值计算

气液两相流的数值模拟是多相混输技术研究中的一个难点.本文假定混输泵叶轮内为泡状流动,基于雷诺时均N-S方程和气液两相双流体模型,采用SIMPLEC算法,对叶片式混输泵叶轮内部两相三维紊流流场进行了数值计算,分析了水气混合工况下的流场分布特点.对含气率GVF=15%工况下的扬程特性进行了预测并与试验结果进行对比.数值计算结果表明,混输泵叶轮流道采用较小的径向尺寸差能较好地避免离心力所引起的气液分离,防止气堵现象的发生;叶轮进口部分存在的低压旋涡区容易使气体积聚,因此有必要进一步改进叶轮进口区的水力设计.     

格子玻尔兹曼方法模拟弯流道中粒子的惯性迁移行为

本文发展了一个能够模拟微流场环境下粒子惯性迁移行为的三维耦合模型.该模型采用基于动理论的格子玻尔兹曼方法(LBM)描述流体流动,采用牛顿动力学模型描述粒子的平动和转动,采用基于LBM反弹格式的运动边界法实现流体与粒子模型的耦合.模拟了重力作用下粒子的沉降过程和Couette流条件下粒子的转动过程,通过将模拟结果与文献中的基准解进行对比定量验证了模型的可靠性.模拟了不同大小的球形粒子在环形流道中的迁移,成功复现了经典的流道截面二次流形成过程,分析了粒径大小对粒子在流道中平衡位置的影响机理.结果表明,粒子在弯流道中的平衡位置与粒径大小密切相关,小半径粒子的平衡位置靠近流道外侧而大半径粒子则靠近流道内侧.通过实验对模拟结果进行了定性验证.本模型为深入研究微流场环境下粒子的运动特性以及开发微流控粒子分选器件提供了参考依据.     

SPH方法气-液界面边界条件研究

针对界面附近粒子光滑函数截断和非物理穿透问题,提出一种气-液界面边界条件的处理方法.当界面附近支持域出现不同材料粒子,每步计算可在支持域设置虚粒子,按照密度分配方法给虚粒子物理量赋值,并对界面附近粒子引入气-液两相阻力.采用SPH方法和Level-Set方法,计算运动激波对气-液界面作用问题,两者计算结果一致,初步验证了气-液界面边界条件处理的适用性.用SPH方法分别计算超声速气流中的圆截面液柱绕流和下落问题,界面两侧粒子压力和法向速度连续,给出弓形激波、回流区和下游回流区等定性合理结果.表明本文方法可适度避免界面附近流体粒子光滑截断和粒子非物理穿透现象、界面附近流场数值振荡.     

SMBR内流体力学特性实验和数值模拟研究

本文基于粒子图像测速(PIV)技术,在不同的曝气强度下对膜面附近的流体力学特性进行了实验研究,结果表明:在一定范围内增加曝气强度可以使得膜面液相速度增加,并应用Euler多相流模型和多孔介质模型耦合对实验结果进行验证。同时本文将气泡羽流的概念应用于SMBR内复杂气液两相流场的研究,并应用气泡羽流分区研究反应器轴向液相速度的变化趋势:液相速度在羽流形成区呈现出先明显增加,而后在羽流形成后区相对较稳定增加,到达表面流区液相速度有所降低,而且极不稳定.结果表明模拟结果与实验结论具有很好的吻合性。     

气液两相流速度及粒径分布激光干涉测量方法的研究

为了实现对气液两相流的粒子粒径、空间分布及其速度测量。对激光干涉气液两相流测量技术（ILIDS）进行了深入研究,该技术是一种应州于气液两相流测量的新技术,其主要优点是不干扰流场和颗粒粒径、位置测量精度高。基于该技术所开发的图像自动处理方法可以利用普通粒子成像测量技术系统拍摄气液两相流的激光散射干涉图像。并利用图像卷积定位、傅里叶变换频率分析及其图像互相关测速等图像处理手段从干涉图像中自动提取粒子的位置、直径和速度信息。为了验证该方法的测量精度,对喷嘴生成的气水两相流进行了测量实验,得到了喷嘴出口处不同区域的粒径、速度矢量的空间分布,并将测得的速度矢量与用粒子成像测量技术方法测得的结果进行对比,证明两种方法测量的平均速度差别仅为0．38％。     

双侧进气突扩燃烧室内液雾燃烧的数值模拟

本文采用全双流体模型对部分切向进气管式双侧进气突扩燃烧室内的液雾燃烧过程进行了数值模拟，将液雾群按初始尺寸分组，数值模拟结果表明不同尺寸液雾的蒸发及燃烧过程显著不同，小尺寸的液雾是先蒸发后燃烧，而较大尺寸的液雾则是边蒸发边燃烧．模拟结果还表明，部分切向进气方式有利于在燃烧室的头部产生大面积的中心回流区，该回流区的存在有利于加强混合及火焰稳定．     

拟涡位移模型及气粒两相流动数值模拟

本文首先用离散涡方法对绕圆柱和半无限长平板的流动作了数值模拟。在讨论粒子和涡团耦合运动的基础上首次提出了粒子在流场中运动的拟涡位移模型，并对几个典型的气粒两相流动作了数值模拟。文章最后对流场中粒子运动的瞬时状态作了统计处理，得到了关于粒子在流场中分布的概率密度函数和粒子脉动速度的分布函数并用拟涡位移模型对壁面附近粒子的运动－沉积和反弹作了数值模拟。计算结果是令人满意的。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.