低密度流体界面不稳定性大涡模拟

采用拉伸涡亚格子尺度应力模型对湍流输运中的亚格子作用项进行模式化处理,发展了适用于可压多介质黏性流动和湍流的大涡模拟方法和代码MVFT（multi-viscous flow and turbulence）。利用MVFT代码对低密度流体界面不稳定性及其诱发的湍流混合问题进行了数值模拟。详细分析了扰动界面的发展,流场中冲击波的传播、相互作用、湍流混合区边界的演化规律,以及流场瞬时密度和湍动能的分布和发展。数值模拟获得的界面演化图像和流场中波系结构与实验结果吻合较好。三维和二维模拟结果的比较显示,两者得到的扰动界面位置、波系及湍流混合区边界基本一致,只是后期的界面构型有所不同,这也正说明湍流具有强三维效应。     

EXPERIMENTALLY STUDY OF THE RICHTMYER-MESHKOV INSTABILITY AT N2/SF6 FLAT INTERFACES BY DIFFRACTED INCIDENT SHOCK WAVES AND RESHOCK

利用高速纹影测试实验研究低马赫数入射激波绕圆柱体后冲击N₂/SF₆平面界面,以及来自固壁的反射激波再冲击过程的（Richmyer-Meshkov,R-M）不稳定性特征.与平面激波作用不同的是,绕射后的激波会在界面处生成局部扰动.实验结果显示,入射激波作用下界面宽度增长缓慢,而反射激波再冲击后,局部扰动会产生大的“尖钉”和“气泡”结构;以及反射激波与边界层相互作用产生壁面涡,它们会加剧湍流混合区的增长;实验中反射激波过后混合区增长率不十分依赖于波前状态,增长规律同Mikaelian模型较吻合;来自尾部固壁的反射稀疏波会再次加剧湍流混合区的增长.     

流场非均匀性对非平面激波诱导的Richtmyer-Meshkov不稳定性影响的数值研究

基于Navier-Stokes方程组,采用可压缩多介质黏性流动和湍流大涡模拟程序MVFT (multi-viscousflow and turbulence),模拟了均匀流场与初始密度呈现高斯函数分布的非均匀流场中马赫数为1.25的非平面激波加载初始扰动air/SF6界面的Richtmyer-Meshkov (RM)不稳定性现象。数值模拟结果表明,初始流场非均匀性将会影响非平面激波诱导的RM不稳定性演化过程。反射激波加载前,非平面激波导致的界面扰动振幅随着流场非均匀性增强而增大;反射激波加载后,非均匀流场与均匀流场条件下的界面扰动振幅差异有所减小。进一步,定量分析流场中环量分布及脉动速度统计量揭示了前述规律的原因。此外,还与平面激波诱导的RM不稳定性进行了简单对比,发现由于非平面激波波阵面区域的涡量与激波冲击界面时产生的涡量的共同作用,使得非平面激波与平面激波诱导的界面失稳过程存在差异。     

可压缩多介质粘性流体和湍流的大涡模拟

在可压缩多介质粘性流体动力学高精度计算方法MVPPM(multi-viscous-fluid piecewise parabolicmethod)基础上,引入Smagorinsky和Vreman亚格子湍流模型,采用大涡数值模拟方法求解可压缩粘性流体NS(Navier-Stokes)方程,给出适用于可压缩多介质流体界面不稳定性发展演化至湍流阶段的计算方法和二维计算程序MVFT(multi-viscosity-fluid and turbulence)。在2种亚格子湍流模型下计算了LANL(Los Ala-mos National Laboratory)激波管单气柱RM不稳定性实验,分析了气柱的形状、流场速度以及涡的特征,通过与LANL实验和计算结果的比较可知,Vreman模型略优于Smagorinsky模型,MVFT方法和计算程序可用于对界面不稳定性发展演化至湍流阶段的数值模拟。     

多次激波诱导正弦扰动预混火焰界面失稳的数值研究

激波诱导火焰失稳是实际中常见的现象,为深入研究火焰失稳特性,采用三维单步化学反应的Navier-Stokes方程和9阶weighted essentially non-oscillatory (WENO)的高精度格式,对不同马赫数的入射激波及其反射激波多次诱导正弦型预混火焰界面失稳的现象进行了三维数值模拟,并对计算结果的可靠性进行了验证。研究结果显示,在激波的多次作用下,火焰界面的演变过程主要受Richtmyer-Meshkov (RM)不稳定特性和化学反应特性的双重影响,且随着入射激波强度的增强,上述2种特性均得到进一步强化。为构造体现反应性RM不稳定特性的参数,根据火焰界面混合区平均涡量和化学反应速率,提出了表征界面受不稳定性和化学反应影响的量纲一参数。通过分析发现,在同一入射激波强度下,该参数的对数形式随入射激波和反射激波的多次作用呈基本相同的线性增长趋势;对不同马赫数的入射激波,该参数对数形式的线性增长率也基本一致。这样的变化表明该量纲一参数能够反映反应性RM不稳定过程中火焰界面发展的内在规律。     

Stability of converging cylindrical shock waves

An experimental and numerical study was made of converging cylindrical shock waves. The goal of the present study was to clarify the movement and instability of the converging cylindrical shock waves. Experiments were conducted in an annular shock tube of 230 mm o.d. and 210 mm i.d. connected to a cylindrical test section of 210 mm diameter. Double exposure holographic interferometry was used to visualize the converging cylindrical shock waves. Incident shock Mach numbers ranged between 1.1 and 2.0 in air. A numerical simulation was conducted using the TVD finite difference scheme. It was found in the experiments that although the initial shock wave configuration looked cylindrical, it was gradually deformed with propagation towards the center and finally showed mode-four instability. This is attributable to the existence of initial disturbances which were introduced by the struts which supported the inner tube of the annular shock tube. This trend was significant for stronger shock waves indicating that at the last stage of shock wave convergence the initial perturbations of the converging cylindrical shock wave were amplified to form the triple point of Mach reflection. The numerical results correctly predicted the experimental trend.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1990.     

Computational and Experimental Investigation of the Development of Turbulent Mixing in a Gas Layering in Passage of a Shock Wave

The experimental data and the results of direct numerical simulation of the flow developed in a constant-cross-section tube in passage of a shock wave through a three-layer gas system are presented. The three-layer systemis formed as a result ofmounting two thin films in the tube and filling the space between them with gases of different densities. The first interface (thin film) makes an angle of 45? with the shock front and the second interface is located in parallel to the front. The shock wave is formed at the left tube end and moves towards the first interface at the Mach number M = 2.4. The results of simulation of the problem are compared with the experimental data.     

Mach reflection of a plane shock wave passing a mountain of 45° inclination

The transition from regular reflection (RR) to Mach reflection (MR) as a plane shock wave diffracts around a triangular mountain of 45° inclination is analysed in this paper, both by optical measurement in a shock tube and by numerical simulation the numerical method developed by Li Yingfan^[1] is of the FLIC type with triangular mesh. The dependence of the critical transition point Lk ofRR→MR on shock Mach numberM _i is analyzed and the variations of the incidence angle ω _i of the impinging shock and the reflection angle ω _r with the distanceL ^* are investigated. Our experimental and numerical results agree well with the theoretical results of Iton and Italya.     

Numerical study of three-dimensional developments of premixed flame induced by multiple shock waves

The three-dimensional interactions of a perturbed premixed flame interface with a planar incident shock wave and its reflected shock waves are numerically simulated by solving the compressible, reactive Navier–Stokes equations with the high-resolution scheme and a single-step chemical reaction. The effects of the initial incident shock wave strength (Mach number) and the initial perturbation pattern of interface on the interactions are investigated. The distinct properties of perturbation growth on the flame interface during the interactions are presented. Our results show that perturbation growth is mainly attributed to the flame stretching and propagation. The flame stretching is associated with the larger-scale vortical flow due to Richtmyer–Meshkov instability while the flame propagation is due to the chemical reaction. The mixing properties of unburned/burned gases on both sides of the flame are quantitatively analyzed by using integral and statistical diagnostics. The results show that the large-scale flow due to the vortical motion always plays a dominating role during the reactive interaction process; however, the effect of chemistry becomes more important at the later stage of the interactions, especially for higher Mach number cases. The scalar dissipation due to the molecular diffusion is always small in the present study and can be negligible.     

On the Mutual Penetrations of Two Fluids Whose Interface is Accelerated by a Shock Wave

A shock tube experimental investigation and numerical simulations are undertaken to study the evolution of a perturbed interface of two different gases accelerated by a shock wave. The experimental method is based on a high-speed camera laser sheet diagnostic technique, and simulations are provided by our code CARBUR based on a finite volume discretization of Navier–Stokes’s equations. Two gas pairs are used to illustrate both the heavy/light (air/He) and the light/ heavy (air/SF₆) cases. Two simultaneous large initial perturbations, one positive and one negative, are tested for an incident shock wave Mach number in air of about 1.3. The thin membrane (less than 1 μ) which materializes the initial interface between the two test gases presents 2D perturbations whose wave number is close to 1 in order to rapidly reach the non-linear regime. The development of the perturbations is captured at a frequency of 10 kHz after the interface acceleration, and the experiments are complemented with a numerical simulation to validate the interface deformations. Results show an asymmetric mutual gas penetration increasing with the absolute value of the Atwood’s number. Furthermore, they confirm that the heavier gas penetrates the lighter as thin spikes and the lighter gas penetrates the heavier as large bubbles. Moreover, we show that the spike moves faster than the bubble in the heavy/light case and slightly faster in the light/heavy one. Finally, numerical and experimental results are in agreement.     

Richtmyer–Meshkov instability on a low Atwood number interface after reshock

The Richtmyer–Meshkov instability after reshock is investigated in shock tube experiments at the Wisconsin Shock Tube Laboratory using planar laser imaging and a new high-speed interface-tracking technique. The interface is a mixture of helium and argon (50% each by volume) stratified over pure argon. This interface has an Atwood number of 0.29 and a near single-mode, two-dimensional, standing wave perturbation with an average amplitude of 0.35?cm and a wavelength of 19.4?cm. The incident shock wave of Mach number 1.92 accelerates the interface before reflecting from the shock tube end wall with M =?1.70 and accelerating the interface in the opposite direction. The amplitude growth after reshock is reported for variations in this initial amplitude, and several amplitude growth rate models are compared to the experimental growth rate after reshock. A new growth model is introduced, based on a model of circulation deposition calculated from one-dimensional gas dynamics parameters. This model compares well with the amplitude growth rate after reshock and the circulation over one-half wavelength of the interface after the first shock wave and after reshock.     

单模大扰动的Richtmyer-Meshkov不稳定性

采用高精度的多介质Ghost-Fluid方法,对马赫数为1.15的激波分别作用于单模大扰动Air-CO2、Air-SF6、Air-N2和Air-He界面后的Richtmyer-Meshkov不稳定现象进行了数值研究,得到了不同时刻扰动界面的演化图像,给出了流场的密度等值线和密度纹影图,同实验结果吻合较好。给出了界面的扰动增长随时间变化的情况,并同理论模型进行了对比。对激波从轻气体进入重气体的情况,扰动增长可采用Sadot模型描述线性阶段和早期非线性阶段;对于弱激波同密度接近的气体界面的相互作用,线性阶段时间较长,可用线性模型描述。     

激波管实验研究非均匀流场R-M不稳定性

利用激波管装置及马赫数为1.27的弱入射激波实验研究了SF6非均匀流场的R-M不稳定性。Air/SF6初始正弦界面由厚度为0.5μm的薄膜相隔得到,由阴影方法记录界面演化过程。实验结果表明:由于不稳定性,重流体(SF6)向轻流体(Air)演化成"尖钉"结构,而轻流体演化为"气泡"结构;由于界面切向速度差的Kelvin-Helmholtz不稳定性,"尖钉"头部翻转成蘑菇头形状;由于流场密度分布不均,低密度区流场扰动增长较快,扰动振幅发展的实验结果与PPM数值计算的结果较吻合。     

激波冲击下air/SF6界面的Richtmyer-Meshkov不稳定性

实验研究了低马赫数(1.27)激波作用air/SF6界面的RM不稳定性问题.air/SF6初始正弦界面由厚度为1～2 μm的薄膜相隔得到,用阴影法测试界面演化过程.实验结果表明:由于不稳定性重流体(SF6)向轻流体(air)演化成“尖钉”结构,而轻流体演化为“气泡”结构;由于界面切向速度差的Kelvin-Helm-ho...     

Generation of polygonal gas interfaces by soap film for Richtmyer–Meshkov instability study

A simple method of generating polygonal gas interfaces is proposed by using the soap film technique. Thin pins are used as angular vertexes to connect the adjacent sides of polygonal soap films in order to avoid the pressure singularities around the vertexes caused by the surface tension. As a demonstration, three polygonal interfaces (i.e., square, equilateral triangle and diamond) are created in the test section of a shock tube. Experiments are then carried out for a planar shock wave (Mach number about 1.2) interacting with air/SF₆ polygonal interfaces. Numerical simulations are also performed to validate the proposed method of the interface formation. Wave systems and interface structures can be clearly identified in experimental schlieren images and agree well with the numerical results. It is also indicated that the presences of thin pins and fine chamfers only have limited effects on the interface evolution and can be ignored at the very early stage. Experimental and numerical results about the movement of the distorted interface, the width and height of the interface structures are further compared and good agreement is achieved. It is then concluded that the polygonal interface formed by the proposed method is applicable for the Richtmyer–Meshkov instability study.     

圆柱形汇聚激波诱导 Richtmyer-Meshkov不稳定的 SPH 模拟

汇聚激波诱导不同物质界面的Richtmyer-Meshkov(RM)不稳定现象在惯性约束核聚变领域有重要的学术意义和工程背景.基于网格离散的宏观流体力学方法由于数值扩散问题往往需要高阶精度算法才能准确追踪界面演化,且对大变形和破碎合并等复杂界面追踪也极为困难.光滑粒子流体动力学(smoothed particlehydrodynamics,SPH)方法采用纯拉格朗日算法,可以有效克服上述难点.但经典SPH算法需采用人工黏性处理强间断,在激波间断处往往会出现严重的非物理振荡,对于涉及强冲击不稳定性问题,很难达到理想的模拟效果.本文采用基于HLL黎曼求解器的SPH算法,实现了对强激波和大密度比物质界面的有效分辨和追踪.一维数值校核证明了代码的可靠性、健壮性,并进一步模拟了二维圆柱形汇聚冲击波冲击四边形轻/重气界面诱导的RM不稳定性问题,与已有实验结果进行了对比,发现模拟结果与实验结果吻合.通过分析界面演化过程中的密度及压力变化,发现本文所采用的方法可准确地追踪激波与界面作用的复杂界面和波系演化规律.研究结果为进一步理解和解释汇聚冲击条件下的RM不稳定性机理奠定了基础.      

Interference between a centered rarefaction wave and an inclined shock wave

The gas flow in the zone of interaction between an oblique shock and a centered isentropic rarefaction wave is studied using the direct statistical simulation method for solving the Boltzmann equation. The data of calculations of the shock and rarefaction wave structures, flow fields, and streamlines are given for the free-stream Mach number M_∞ = 6, 4 and 2. The formation of the interaction zone is simulated by a gas flow past a double-plane wedge in which the break of the generating line leads to formation of the centered isentropic rarefaction wave. The results of calculations of this flow in solving the Boltzmann equation are given in the Euler approximation.     

激波诱导下的气体界面不稳定性实验研究

界面不稳定性, 特别是Richtmyer–Meshkov (RM) 不稳定性, 是流体
力学中一项重要的研究内容, 无论在学术研究领域还是工程应用领域都有着
重要的研究价值和应用背景. RM 不稳定性问题自提出以来, 得到了学术界
广泛的关注, 其研究无论是在实验方法、数值模拟还是在理论分析方面都取
得了很大的进展. 在激波管中开展激波与界面相互作用的实验研究, 即研究
界面初始扰动在激波诱导下的演化规律, 是目前研究RM 不稳定性的重要手
段. RM 不稳定性实验研究包括3 个部分, 分别是激波的产生、界面的形成
以及流场的观测. 综述了RM 不稳定性的实验研究进展, 并针对目前研究的
局限性提出了RM 不稳定性今后实验研究的重点和方向: 汇聚激波作用下界
面不稳定性的发展规律; 激波冲击下多种形状及大振幅界面的演化机理; 三
维界面的RM 不稳定性发展规律; 可压缩湍流的形成与混合机理.      

柱形汇聚激波冲击球形重气体界面的实验研究

采用高速纹影法实验研究了柱形汇聚激波与球形重气体界面相互作用的 Richtmyer-Meshkov不稳定性问题. 激波管实验段基于激波动力学理论设计, 将马赫数为1.2 的平面激波转化为柱形汇聚激波, 气体界面由肥皂膜分隔六氟化硫(内)和空气(外)得到. 采用高速摄影机在单次实验中拍摄激波运动的全过程, 对柱形激波的形成进行了实验验证, 并进一步观测了汇聚激波与球形气体界面相互作用过程中的波系发展和气体界面变形以及反射激波同已变形界面二次作用的流场演化. 结果表明: 当柱形汇聚激波穿过气泡界面以后, 气泡左侧界面极点沿激波传播方向保持匀速运动, 气泡右侧界面发展成为射流结构, 气泡主体发展成为涡环结构; 在反射激波的二次作用下, 流场中无序运动显著增强并很快进入湍流混合阶段.     

HLLE++格式在高马赫数空腔流动模拟中的应用

空腔流动存在剪切层运动、涡脱落与破裂,以及激波与激波、激波与剪切层、激波与膨胀波和激波/涡/剪切层相互干扰等现象,流动非常复杂,特别是高马赫数(M>2)时,剪切层和激波更强,激波与激波干扰更严重,对数值格式的要求更高,既需要格式耗散小,对分离涡等有很高的模拟精度,又需要格式在激波附近具有较大的耗散,可以很好地捕捉激波,防止非物理解的出现。Roe和HLLC等近似Riemann解格式在高马赫数强激波处可能会出现红玉现象,而HLLE++格式大大改善了这种缺陷,在捕捉高超声速激波时避免了红玉现象的发生,同时还保持在光滑区域的低数值耗散特性。本文在结构网格下HLLE++格式的基础上,通过改进激波探测的求解,建立了基于非结构混合网格的HLLE++计算方法,通过无粘斜坡算例,验证了HLLE++格式模拟高马赫数流动的能力,并应用于高马赫数空腔流动的数值模拟,开展了网格和湍流模型影响研究,验证了方法模拟高马赫数空腔流动的可靠性和有效性。