酞侧基聚芳醚砜／对苯二甲酸乙二酯－对羟基苯甲酸嵌段共聚物共混物的研究

酞侧基聚芳醚砜／对苯二甲酸乙二酯－对羟基苯甲酸嵌段共聚物共混物的研究李刚，殷敬华，李滨耀（中国科学院长春应用化学研究所，长春，１３００２２）关键词酞侧基聚芳醚砜，热致性液晶高聚物，原位复合材料，对苯二甲酸乙二酯－对羟基苯甲酸嵌段共聚物将热塑性树脂与热...     

热致液晶PEI与PES—C共混物的研究

通过熔融共混,制备不同配比（２．５／９７．５－７５／２５）的ＰＥＩ／ＰＥＳ－Ｃ共混物,使用ＷＡＸＤ、ＤＳＣ、锥板流变仪、力学性能测试、ＳＥＭ等方法对共混物进行了研究。共混后强度、模量均有提高,在高剪切速率下,共混物的粘度有所降低。扫描电镜照片显示,共混物具有“皮芯”结构。     

热致液晶共聚酯／含酚酞侧基聚芳醚砜共混物的流变行为研究

采用溶液共混制备耻不同比例的热致液晶共聚酯／含酚酞侧基聚芳醚砜共混物。利用锥板流变仪对共混体系的熔体流变性能进行了初步研究，测定了熔体粘度－温度、粘度－剪切速度的关系，结果表明该液晶聚合物能明显降低聚芳醚砜的熔体粘度。     

Thermal Properties and Morphology of Liquid Crystalline Copolyester and Polyester Elastomer Blends

Abstract

Polyester elastomer (PEL) blends having a hard segment of polyester (PBT), soft segment of polyether (PTMG), and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate) were prepared with a twin-screw extruder. Test specimens for thermal properties were prepared by injection molding. Rheological properties and morphology were investigated by Instron capillary rheometer (ICR) and scanning electron microscopy (SEM). Thermal properties of the LCP/PEL blends were investigated by DSC, dilatometer, heat deflection temperature tester, and a Rheovibron viscometer. DSC study revealed a partial miscibility between LCP and PEL. It was found that the LCP acted as a nucleating agent for the crystallization of PEL in the LCP/PEL blends. The dimensional and thermal stability of the blends were increased by increasing the LCP cont-ent. The storage modulus (E' was improved by increasing the LCP content. The blend viscosity showed a minimum value at 5 wt% of LCP which increased by increasing the LCP content above 5 wt% of LCP The morphology of the LCP/PEL blends showed poor interfacial adhesion between the two phases, and the fibrillar structure of LCP phase in the matrix was affected by the LCP content, shear rate, and extrusion temperature. The morphology of the blends was found to be affected by their compositions and processing conditions.     

酞侧基聚芳醚砜／聚苯硫醚共混物的形态与力学性能

酞侧基聚芳醚砜（ＰＥＳ－Ｃ）与聚苯硫醚（ＰＰＳ）具有部分相容性，虽然ＰＰＳ的强度和韧性均低于ＰＥＳ－，但ＰＰＳ含量为２％～１０％的ＰＥＳ－Ｃ／ＰＰＳ共混物在保持ＰＥＳ－Ｃ原有强度，断裂伸长率的同时，模量略增，冲击强度有很大幅度提高，熔融指数亦蛔。     

热致液晶／PEEK／嵌段共聚物共混体系的结构与性能

用ＷＡＸＤ、ＳＥＭ及力学性能测试等研究热致液晶／ＰＥＥＫ／嵌段共聚物三元共混体系形态、结构和性能。结果表明嵌段共聚物的加入，使体系具有一定的相容性和较好的界面粘接，共混物的强度、模量有一定的提高，对共混物的结晶行为具有明显的影响，当热致液晶含量高时，基材与液晶两相间出现明显的分离现象，即“皮－芯”结构．     

Mutual influence of the morphology and capillary rheological properties in nylon/glass‐fiber/liquid‐crystalline‐polymer blends

Nylon‐6/glass‐fiber (GF)/liquid‐crystalline‐polymer (LCP) ternary blends with different viscosity ratios were prepared with three kinds of nylon‐6 with different viscosities as matrices. The rheological behaviors of these blends were characterized with capillary rheometry. The morphology was observed with scanning electron microscopy and polarizing optical microscopy. This study showed that although LCP did not fibrillate in binary nylon‐6/LCP blends, LCP fibrillated to a large aspect ratio in some ternary blends after GF was added. The addition of 5 wt % LCP significantly reduced the melt viscosity of nylon‐6/GF blends to such an extent that some nylon‐6/GF/LCP blends had quite low viscosities, not only lower than those of neat resins and nylon‐6/GF blends but also lower than those of corresponding nylon‐6/LCP blends. The mutual influence of the morphology and rheological properties was examined. The great reduction of the melt viscosity was considered the result of LCP fibrillation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1619–1627, 2004     

Properties of immiscible and ethylene-butyl acrylate-glycidyl methacrylate terpolymer compatibilized poly (lactic acid) and polypropylene blends

Poly(lactic acid) (PLA) and polypropylene (PP) blends of various proportions were prepared by melt-compounding. The miscibility, phase morphology, thermal behavior, and mechanical and rheological properties of the blends were investigated. The blends were immiscible systems with two typical morphologies, spherical droplet and co-continuous, and could be obtained at various compositions. Complex viscosity, storage modulus and loss modulus depend on the PP content. Thermal degradation of all blends led to two weight losses, for PLA and PP. The incorporation of PP improved the thermal stability of the blend. The effect of compatibilizer (ethylene-butyl acrylate-glycidyl methacrylate terpolymer, EBA-GMA) on the morphology and mechanical properties of 70/30 w/w PLA/PP blends was investigated. The tensile strength of these blends reached a maximum for 2.5 wt% EBA-GMA, and impact strength increased with increasing EBA-GMA content, suggesting that EBA-GMA is an effective compatibilizer for PLA/PP blends.     

显微镜图像分析研究聚丙烯/尼龙1010共混物相结构及其性能

用扫描电子显微镜图像分析研究了聚丙烯/聚酰胺1010共混物及其部分相容体系的相形态结构,计算了表征相结构和尺寸的结构参数,如分散相的平均直径、平均弦长和分散相的质心相关距等.并分别讨论了聚丙烯/聚酰胺1010共混物及其部分相容体系的相形态以及其结构参数与共混物组成的关系.测定了聚合物及其共混物体系的力学性能,讨论了共混物组成与力学性能的关系.聚丙烯/聚酰胺1010共混物的拉伸模量与组成的关系较为复杂,但其部分相容体系的拉伸模量与组成呈线性关系.聚丙烯/聚酰胺1010及其共混物体系的屈服强度与共混物组成均呈线性关系.表征相结构的两相平均弦长比(l-1/-l2)与组成以及共混物体系力学性能与组成的关系,二者相似.同时讨论了体系力学性能随相尺寸等的变化规律.     

含热致液晶性共聚酯的聚砜共混物

将一种含萘环的热致液晶性共聚酯与聚砜材脂熔融共混并挤塑成条．毛细管流变性测试表明，这一共聚酯降低了共混物的表观粘度，甚至低于其本身的粘度．共混物受剪切作用形成了各向异性的微纤增强结构，并具有皮芯结构．在液晶聚合物含量低到２％与０．５％的样条中仍有共聚酯微纤形成．共聚酯微纤提高了聚砜的力学性能，含２０％共聚酯共混物挤塑条的位伸模量为聚砜树脂的二倍半．