基于MCM-41分子筛表面的镱离子印迹聚合物的制备及其性能

运用离子印迹技术,以3-氯丙基三乙氧基硅烷为锚定剂,将功能单体直链聚乙烯亚胺(PEI)接枝在MCM-41分子筛表面,选择镱离子作为模板离子,以环氧氯丙烷交联制备出基于MCM-41表面的镱离子印迹聚合物Yb(Ⅲ)-IIP-PEI/MCM-41,并以同样的方法制备非离子印迹聚合物(NIP-PEI/MCM-41)。 利用傅里叶变换红外光谱仪和扫描电子显微镜等技术手段对Yb³⁺印迹聚合物进行表征,采用静态吸附法确定了Yb(Ⅲ)-IIP-PEI/MCM-41对Yb³⁺的最佳吸附条件及选择性吸附性能。 结果表明,Yb(Ⅲ)-IIP-PEI/MCM-41和NIP-PEI/MCM-41的最大吸附量分别为229.93和99.27 mg/g;印迹材料对Yb³⁺的吸附符合Langmuir模型;吸附平衡在40 min的时候基本可以达到,可以利用准二级动力学模型来描述其吸附过程;Yb(Ⅲ)-IIP-PEI/MCM-41对Yb³⁺具有较强的选择性,同时也具有很好的重复使用性能。 成功地将MCM-41和离子印迹聚合物的优点结合起来,制备出一种对稀土Yb离子既有高吸附量又有高选择性的吸附材料,为进一步将其应用在处理实际废水,分离回收低浓度稀土废水中的稀土元素等方面打下了基础。     

杂原子介孔Co-MCM-41分子筛的制备及其吸附脱氮性能

采用水热法合成了介孔MCM-41和Co-MCM-41分子筛,并利用XRD、FT-IR、低温N₂吸附-脱附和NH₃-TPD等方法对合成的分子筛进行了表征。考察了晶化时间、晶化温度、陈化时间对合成介孔Co-MCM-41分子筛的影响,确定较适宜的合成条件为陈化时间1 h,晶化温度110 ℃,晶化时间2 d。XRD 和FT-IR表征结果说明,Co原子已经进入MCM-41的骨架。MCM-41和Co-MCM-41的平均孔径均为2.82 nm,BET比表面积分别为986.42和 637.69 m²/g,孔容分别为0.762 1和0.537 2 m³/g。NH₃-TPD的表征结果表明,MCM-41和Co-MCM-41的酸性都较弱,但Co-MCM-41的酸性明显强于MCM-41。在此基础上,利用合成的MCM-41和Co-MCM-41吸附脱除氮含量为1 737.35 μg/g的模拟燃料中的喹啉。喹啉分子尺寸的模拟结果为0.711 6 nm × 0.500 2 nm,说明其可以很容易地进入MCM-41和Co-MCM-41的介孔孔道中。Co-MCM-41分子筛的氮脱除率明显高于MCM-41,这是由于其较强的酸性及与喹啉之间的化学吸附,而且,Co-MCM-41吸附脱氮具有较好的再生性能。     

Study on the controllable synthesis of SH-MCM-41 mesoporous materials and their adsorption properties of the La3+, Gd3+ and Yb3+

SH-MCM-41 was examined in adsorption and desorption experiments to investigate the adsorption capacities of La³⁺, Gd³⁺ and Yb³⁺ and the reusability.     

杂原子介孔Co-MCM-41分子筛的制备及其柴油深度吸附脱碱氮性能

以硝酸钴为钴源,采用水热法合成了MCM-41和不同Co含量的Co-MCM-41分子筛,并利用XRD、FT-IR和低温N2吸附-脱附等方法对合成的分子筛进行表征。当加入的Co/Si物质的量比达到0.1时,依然能够成功合成具有规整有序的介孔结构的Co-MCM-41。MCM-41和Co-MCM-41静态吸附脱除0#柴油中碱氮的实验结果表明,Co/Si物质的量比为0.06的Co-MCM-41(2)分子筛的吸附容量最大,达到5.324 mg(N)/g分子筛,明显高于MCM-41分子筛的吸附容量2.532 mg(N)/g,说明Co进入MCM-41分子筛骨架后显著提高了分子筛的吸附脱除碱氮能力。当加入的Co/Si物质的量比大于0.06时,分子筛吸附脱除柴油中碱氮的能力反而下降,这是由于加入过多Co会使其以Co3O4形式高度分散在分子筛孔道中,堵塞了吸附活性位,使其无法与碱性氮化物接触造成吸附脱氮能力下降。动态吸附脱除0#柴油中碱性氮化物的结果表明,每克CoM CM-41(2)分子筛可将35 m L柴油的碱氮从147.54μg/g吸附脱除到10μg/g以下,吸附容量为4.2 mg(N)/g(吸附剂),由于动态吸附的接触时间较短使MCM-41失去了吸附脱氮能力,说明Co-MCM-41(2)对柴油中的碱氮具有较好的选择性。     

Immobilization of Keggin and Preyssler tungsten heteropolyacids on various functionalized silica

The Keggin and Preyssler tungsten heteropolyacids, H3PW12O40 and H15P5W30O110, have been immobilized on the inner surface of mesoporous MCM-41, fume silica and silica-gel by means of chemical bonding to aminosilane groups. The materials were characterized by FT-IR spectroscopy, low-angle XRD and BET surface area analysis. The tendencies of heteropolyacids adsorption in solution on functionalized silicas have been investigated by UV-vis. Among the functionalized silica materials, MCM-41 showed the largest amine to silica and the least heteropolyacid to silica ratios. The BET surface area revealed that in all three cases the surface area decreased after grafting amine group and anchoring of the HPAs clusters. Low-angle XRD analysis showed that by introducing HPA into functionalized MCM-41 the intensity of the main reflection decreased significantly.     

Morphology of nanostructured platinum in mesoporous materials-effect of solvent and intrachannel surface

An intrachannel surface of host silica was functionalized through the reaction of surface silanol groups with silanes to generate a monolayer of positively charged groups, and together with the strongly adsorbed and negatively charged PtCl6(2-), resulting in nanostructured platinum-mesoporous silica composites. The highly dispersed Pt nanoparticles and nanonetworks are fabricated from (CH3O)3Si(CH2)3N(CH3)3+Cl- functionalized mesoporous silica MCM-48 with H2PtCl6 in ethanol and water solvent, and characterized by PXRD, XAS, TEM, and N2 adsorption. The solvent of H2PtCl6 solution is found to affect the mobility of Pt precursors and the resulting morphology of nanostructured metallic Pt. The effect of the intrachannel surface properties on the incorporation and the morphology of nanostructured Pt on the deposition of Pt(NH3)4Cl2 and H2PtCl6 on Al-doped or C-coated mesoporous silica MCM-41 is also studied relative to that on pure silica MCM-41.     

新型多级微/介孔固态胺吸附剂的制备及其CO2吸附性能研究

将HZSM-5与MCM-41按不同质量比混合得到复合分子筛载体,以四乙烯五胺(TEPA)为改性剂,采用浸渍法将其负载到复合分子筛上,制备了一系列新型的具有多级微/介孔结构的固态胺吸附剂。采用N₂吸脱附、傅里叶变换红外光谱(FT-IR)、热重分析(TGA)等手段对吸附剂进行表征。在固定床反应器中考察了HZSM-5和MCM-41的质量比、TEPA负载量、吸附温度、进气流量和CO₂分压等因素对CO₂吸附性能的影响。结果表明,当HZSM-5与MCM-41的质量比为1:1、TEPA负载量为30%、吸附温度为55℃、进气流量为30 mL/min时,平衡吸附量高达3.57 mmol/g,且经10次吸脱附循环后,吸附量仅下降8.1%。HZSM-5/MCM-41-30%TEPA对CO₂的吸附过程包括快速的穿透吸附和相对缓慢的逐渐平衡阶段,且穿透吸附量接近于平衡吸附量的80%。HZSM-5/MCM-41-30%TEPA对CO₂的吸附过程符合Avrami动力学模型,表明CO₂吸附是物理吸附和化学吸附的结果。     

杂原子介孔MCM-41分子筛的制备及其对含喹啉模拟柴油的吸附脱氮性能

制备了介孔MCM-41分子筛和三种杂原子(Zn、Ba和Ce)介孔MCM-41分子筛,通过X射线衍射(XRD)、红外光谱(FT-IR)、低温N_2吸附-脱附等手段对其进行表征,研究了几种介孔分子筛对氮含量为1732μg/g含喹啉模拟柴油的吸附脱氮性能。结果表明,所制备的几种分子筛均具有典型的介孔结构,且杂原子已进入到分子筛骨架中。利用Materials Studio软件构建介孔分子筛模型,模拟的XRD谱图与实验结果基本相符;进一步模拟了喹啉分子在杂原子介孔分子筛团簇上的吸附,计算了吸附能及被吸附分子和吸附中心的距离(d_((N-M)))。几种分子筛的吸附脱氮性能顺序依次为Zn-MCM-41 Ce-MCM-41 Ba-MCM-41 MCM-41;Zn-MCM-41的吸附性能最好,吸附能最大,吸附分子和吸附中心的距离d_((N-M))最小。吸附时间对杂原子介孔分子筛的吸附脱氮性能具有较大影响,而吸附温度的影响相对较小;Zn-MCM-41、Ba-MCM-41和Ce-MCM-41分子筛的最佳吸附时间分别为40、10和30 min,最佳吸附温度分别为40、30和40℃。     

ZSM-5/MCM-41复合分子筛的合成与表征

以碱处理的ZSM-5浆液为硅铝源,通过水热自组装过程合成了介孔-微孔复合孔道结构的分子筛,并采用XRD、BET、HRTEM、Py-IR和水热处理等手段对合成分子筛进行了表征。结果表明,碱处理ZSM-5时的苛刻程度是影响复合分子筛合成的重要因素,适宜的碱处理条件为NaOH浓度1 mol/L、80℃时处理1 h。表征结果表明,复合分子筛具有规整互通的微孔-介孔梯级复合孔道结构,孔容、比表面积和平均孔径分别为0.63 mL/g,684 m²/g和3.76 nm,属典型的MCM-41结构;与MCM-41相比,复合分子筛的B酸(尤其是强B酸)酸量明显增强,水热稳定性显著提高。     

氯苄基官能化和氯苄基甲基双官能化介孔分子筛MCM-41的合成与表征

首先比较了氯苄三乙氧基硅烷和氯苄基三氯硅烷硅烷化介孔分子筛MCM-1的差异性,进而采用氯苄基三氯硅烷和甲基三氯硅烷混合试剂硅烷化介孔分子筛,一步得到氯苄基甲基双官能化介孔分子筛MCM-41,并用固体核磁予以证实.发现甲基三氯硅烷一方面可以作为一种“稀释剂”调节氯苄基的负载量,另一方面甲基的引入可增强介孔分子筛的水热稳定性.     

光沉积法合成纳米金属Pd负载的MCM-TiO2及其光催化性质研究

用光沉积方法由PdCl₄^2-和Ti修饰的MCM-41合成了纳米钯团簇Pd/MCM-TiO₂,用XPS,N₂吸脱附等温线,UV-Vis和Raman光谱对其结构进行了表征.将该团簇用于苯酚的光降解和Cr(Ⅵ)还原为Cr(Ⅲ)的反应中,表现出较高的光催化活性.     

VOCs在吸附剂上吸附性能的热力学研究

采用色谱法与热重(TG)法,测量了正己烷、甲苯和乙酸乙酯在活性炭、5A、NaY、13X、ZSM-5 (SiO_2/Al_2O_3=27、300)、Hβ以及M CM-41等吸附剂上不同温度下的吸脱附行为,并基于反相气相色谱法测得的数据,计算了其吸附热力学参数ΔH、ΔS和ΔG,分析了上述VOCs分子与吸附剂之间的作用机制,并借助FT-IR验证了吸附质在分子筛表面的吸附机制。结果表明,上述吸附过程存在物理吸附和化学吸附两种方式,其中,物理吸附的作用力大小与吸附剂的孔径分布和分子直径相关,而化学吸附的作用力大小依赖于分子筛硅铝比和Ca~(2+)、Na~+、H~+等阳离子及吸附质分子的偶极矩,且强的化学吸附使得部分吸附质分子的脱附温度高于200℃。     

Removal of complexed mercury by dithiocarbamate grafted on mesoporous silica

Mesoporous silica (MCM-41) with d ₍₁₀₀₎ interplanar distance of 38 Å was prepared by a room temperature process through low surfactant templation technique. The surface of MCM-41 was functionalized with dithiocarbamate (dtc) ligand, named as MCM-41-dtc and this was characterized by X-ray diffraction, BET surface area, particle size analysis, ²⁹Si MAS NMR spectra and sulphur analysis. The sorption of mercury from 0.1M HCl solution by MCM-41-dtc was studied as a function of pH, [Hg²⁺], time and temperature. The sorption data obtained at various initial concentrations of mercury were fitted into Langmuir adsorption model. Mercury speciation in solution and the sorption capacity measurements indicated possible formation of a 1 : 1 square planar complex in the solid phase. A very rapid sorption of mercury was observed in the initial stages of equilibration, which can be attributed to the large surface area, wide porosity and fine particle size of MCM-41-dtc, facilitating facile accessibility of mercury into the inner pores of the sorbent. The enthalpy change accompanied by the sorption of mercury was found to decrease from 83.7 to 6.2 kJ/mol, when the initial concentration of mercury was increased from 5^.10^-4M to 1.5^.10^-3M.     

萘在介孔分子筛MCM-41与SBA-15上的吸附特性研究

对低浓度气相萘在两种常见介孔分子筛MCM-41和SBA-15上的吸附特性进行研究。得到了萘在两种吸附剂上的吸附等温线和不同初始浓度下的穿透曲线,并分别与吸附等温线模型(Langmuir、Freundlich、D-R)和恒定浓度波动力学模型进行了拟合。结果表明, Langmuir模型能很好描述低浓度气相萘的吸附等温线(R²均在99%以上);具有微孔结构的SBA-15对萘的吸附能力要优于仅具备介孔结构的MCM-41。动力学模型在初始浓度较低时能较好地预测萘在吸附剂上的穿透曲线,且在SBA-15上的相关系数高于MCM-41;萘在2.76 mol/L时具有较大介孔的SBA-15的总传质系数K_a更高,表明萘在SBA-15上的总传质阻力更低,更能较快达到传质平衡。     

萘普生在介孔分子筛MCM-41中的负载及其溶出性能

用含氨基的偶联剂修饰介孔分子筛MCM-41的表面,将修饰前和修饰后的介孔分子筛分别负载难溶性药物萘普生（NAP）,利用X射线衍射、傅里叶变换红外光谱、差示扫描量热分析、扫描电子显微镜、透射电子显微镜和N2吸附 脱附分析等技术分别对其进行了结构表征和性能测试。 结果表明,药物分子存在于分子筛的孔道中。 负载在MCM-41中的萘普生溶出速率远优于原料药,60 min时大约溶出70%。 氨基修饰后的药物释放速率比修饰前有所减慢,表明可通过氨基修饰调节释放速率。     

Synthesis,characterization of Nafion-functionalized MCM-41 and its catalytic application in preparation of CL-20 via HNO3 electrolyte involved nitration of TAIW

Hybrid organic–inorganic MCM-41 (Mobil Composition of Matter No. 41) silicas functionalized with Nafion (perfluoroalkylsulfonic acid analogous) were prepared and characterized by Fourier Transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and N₂ adsorption analysis. The Brønsted acidity was determined by UV spectrophotometer. The prepared catalyst (SA/MCM-41) exhibited high catalytic activity in the nitration of TAIW (tetraacetylhexaazaisowurtzitan) aiming at synthesizing CL-20 (hexanitrohexaazaisowurtzitane), with the yield up to 93%. The leaching problem was not observed after several runs, demonstrating that the catalyst could be recycled and reused without losing activity.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

Adsorption and protection of plasmid DNA on mesoporous silica nanoparticles modified with various amounts of organosilane

Ordered MCM-41-type mesoporous silica nanoparticles (MSNs) with pore size of 2.6 nm were synthesized and were further modified with various amounts of 3-aminopropyltriethoxysilane (APTES), respectively, by a direct co-condensation method. These amine functionalized mesoporous silica nanoparticles (Am-MSNs) were employed to complex with plasmid DNA (pDNA) to study their adsorption and protection capacities. The results demonstrate the MSNs functionalized with aminopropyl groups present advanced adsorption capacities for pDNA immobilization. And Am-MSNs with high APTES amount lead to high amount of pDNA adsorption. Further investigation of pDNA protection shows that Am-MSNs with moderate APTES amount could completely protect pDNA from enzymatic degradation, while those with smaller and/or higher amount of APTES could partially provide protection of pDNA.     

PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价, 并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3, PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能. 发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性. 实验结果表明, 纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原, 导致铂金属分散度和催化剂的丙烷脱氢活性较低. 用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用, 提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性. 并且, 积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度, 故具有较高的丙烷脱氢反应稳定性. PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能可能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关, 而且与Al2O3/MCM-41载体的介孔结构有关.     

Synthesis, structure, and acidic properties of MCM-41 functionalized with phosphate and titanium phosphate groups

Mesoporous molecular sieves Si-MCM-41 (purely siliceous) and Ti-MCM-41 (partly covered with a surface layer of TiO2) were functionalized with phosphate groups by treatment with POCl3 (denoted -MCM-41(P)and Ti-MCM-41(P), respectively). With the use of TEM, X-ray diffraction, and N2 adsorption, it was shown that the initial hexagonal structure, the high specific surface area, and porosity are retained in the functionalized materials but are not as good as in the starting materials. 1H MAS NMR and 31P MAS NMR revealed that the surface of Si-MCM-41(P) consists of silicon phosphate and pyrophosphate species. That of Ti-MCM-41(P) additionally contains titanium dihydro-, hydro-, and pyrophosphate species, the latter being predominant. TPD of adsorbed ammonia for Si-MCM-41(P) and Ti-MCM-41(P) showed that functionalization leads to the creation of moderate and strong acid sites. A combination of mesoporous structure with acidic properties makes the MCM-41 functionalized with phosphate groups promising for use as solid acid catalysts.