Ag(TCNQ)准一维微米结构的制备及表征

利用溶液化学反应法制备了准一维结构的金属有机配合物Ag(TCNQ). X射线衍射(XRD)表明，所制备的Ag(TCNQ)为晶态结构;扫描电子显微镜(SEM)的观察证明，Ag(TCNQ)为准一维的微米管或线；Raman 测试结果表明，单根的Ag(TCNQ)形成时,Ag原子与TCNQ分子之间发生了电荷转移.对样品的制备工艺,即 Ag膜厚度和浸入溶液的反应时间对生成Ag(TCNQ)晶体形貌的影响进行了研究.结果表明，Ag膜越薄，生长出的晶体越稀疏;Ag膜与TCNQ乙腈溶液的反应时间影响其形貌的变化.反应历经三个阶段,晶体形成和长大阶段、反应完全阶段及溶解阶段.     

湿度对Cu/TCNQ金属有机双层膜化学传质的影响研究

采用真空蒸发方法制备了Cu/TCNQ金属机双层膜. 系统研究了湿度对CuTCNQ络合物形成过程的影响规律, 结果表明湿度对膜的化学反应传质过程有明显加速作用. 过程机制在干燥条件与湿度作用条件下有本质不同: 前者为固体化学扩散机制, 而后者为水溶液电化学反应机制. 进一步深入分析传质时间与湿度的关系后发现, 湿度条件下薄膜对水分子的吸附是反应传质速度的控制步骤.     

分子导体:[NCBzPy][TCNQ]2和[FBzPy][TCNQ]2的合成及光谱研究

合成了两种新的取代苄基吡啶盐[NCBzPy]Cl(1)和[FBzPy]cl(2),1(或2)与LiTCNQ,TCNQ进一步反应生成[NCBzPy][TCNQ]2(3){或[FBzPy][TCNQ]2(4)}。IR研究表明：TCNQ盐中存在TCNQ^o和TCNQ^-,并形成了一维TCNQ分子柱,且TCNQ^o和TCNQ^-之间存在相互作用,有部分电荷发生转移。     

过渡金属吡啶配离子的TCNQ电荷转移盐的合成和物理性质

合成了通式为[M(Py)_m][TCNQ]_n(M=Mn,m＝4;M＝Co,Ni,Cu,m＝2;TCNQ＝7,7,8,8-四氰基对苯醌二甲烷,n＝2,3)的8个过渡金属吡啶配离子的TCNQ电荷转移盐,通过元素分析、红外光谱、顺磁共振谱、光电子能谱、磁化率和电导率对这些电荷转移盐进行了表征,结果表明,在这些电荷转移盐分子中存在TCNQ^-和TCNQ⁰,且TCNQ^-与TCNQ⁰相互作用形成结构单元[TCNQ]_n^2-(n＝2,3),各个结构单元沿一维方向堆积形成分子柱,部分电荷从[TCNQ]_n^2-向[M(Py)_m]²⁺转移,导致化合物中的金属表现为混合价态.其中3个电荷转移盐具有良好的导电性.     

两种表征金属有机双层膜络合和金属薄膜氧化反应动力学的方法

建立了两种新的薄膜反应动力学表征方法, 即透射光谱法和方块电阻法, 以克服传统动力学表征手段在薄膜体系氧化与络合反应过程中应用的局限性. 以透射光谱为表征手段, 得到了Ag/TCNQ(四氰基对醌二甲烷)金属有机双层薄膜的络合反应动力学曲线; 以方块电阻为表征手段, 得到了Cu薄膜的氧化反应动力学过程.     

胺铜或镍配离子的TCNQ电荷转移盐的合成和物理性质

合成了七个胺铜或镍配离子的TCNQ电荷转移盐[ML2][TCNQ]n(TCNQ=7, 7, 8, 8-四氰基对苯二醌二甲烷; n=2, 3;M=Cu, Ni; L=tn, pn, dien, dmtade)。通过元素分析、红外光谱、电子光谱、顺磁共振谱、光电子能谱、磁化率和电导率对这些电荷转移盐进行了表征。结果表明, 这些电荷转移盐分子中存在TCNQ^0和TCNQ^-且TCNQ^0与TCNQ^-之间存在相互作用, 部分电荷从[TCNQ]n^2向[ML2]^2^+转移, 导致化合物中的金属表现为混合价态。七个样品的室温电导率在10^-^5～10^-^1^0S.cm^-^1, 属于有机半导体, 其导电性主要归结为一维TCNQ分子柱的形成。     

基于7,7,8,8-四氰基对醌二甲烷-氯化锰反应的二价锰配合物的合成,晶体结构和磁性(英文)

以氯化锰、双二苯基膦酸甲烷(dppm)及7,7,8,8-四氰基对醌二甲烷(TCNQ)为原料,合成了标题化合物[Mn(dppmdo)_3][(TCNQ)(DCBE)]1;利用X射线衍射、红外光谱、紫外-可见-近红外光谱和循环伏安等技术对合成产物进行了表征.结果表明,化合物1在近红外区发生配体TCNQ之间的电子转移(TCNQ/TCNQ~-).化合物1中的TCNQ比游离态的TCNQ分子更容易被还原.室温下,化合物1的有效磁矩(12.7μB)远高于预期的由一个高自旋Mn~(2+)离子(S=5/2)、一个TCNQ(S=1/2)阴离子及一个DCBE(S=1/2)阴离子组成基团的有效磁矩(4.58μB),表明它们之间存在着很强的磁相互作用.     

银-四氰基对苯二醌二甲烷纳米线阵列的制备及其场发射性能

采用多孔氧化铝模板法, 通过四氰基对苯二醌二甲烷(TCNQ)与金属Ag的化学反应, 制备了银-四氰基对苯二醌二甲烷(AgTCNQ)纳米线阵列. AgTCNQ的直径由多孔氧化铝模板的内孔直径决定, 而其长度则可由反应时间与多孔氧化铝膜模板的厚度来控制. 所制备的AgTCNQ纳米线阵列表面光滑, 直径均一, 具有良好的场发射特性.     

DEA(TCNQ)2与TEA(TCNQ)2单晶上的STM热化学烧孔性能比较

利用STM隧道电流焦耳热诱导分解气化的热化学烧孔方法,对两种存储材料DEA(TCNQ)2和TEA(TCNQ)2的存储性能作了比较,DEA(TCNQ)2可以得到更高的存储密度、更大的信息孔深/孔径比,有更大的写入阈值电压.由此说明通过对存储材料的设计可以对存储系统的性能进行优化.     

2-十八烷基-7,7,8,8-四氰基对醌二甲烷和3,3′,5,5′-四甲基联苯胺电荷转移配合物LB膜的制备和表征

利用LB技术制备了2-十八烷基-7,7,8,8-四氰基对醌二甲烷(C18TCNQ)和3,3,′5,5′-四甲基联苯胺(TMB)的电荷转移配合物(CT comp lex)薄膜,即TMB.C18TCNQ LB膜.利用红外(IR)光谱、紫外-可见-近红外(UV-V is-NIR)光谱以及原子力显微镜(AFM)研究了TMB.C18TCNQ在LB膜中的分子取向、结构及表面形貌.结果表明,配合物为混合堆积类型,LB膜中电子给体TMB和电子受体C18TCNQ的环面分别垂直于固体基板表面,而且给体和受体以面对面的方式堆积.5层TMB.C18TCNQ LB膜的AFM照片显示,其表面形貌是由许多堆积在一起的六边形片状微晶组成的,微晶的宽度约为180 nm.与通过LB技术和掺杂技术制备的TMB.C18TCNQ掺杂膜比较,TMB.C18TCNQ LB膜具有明显不同的结构,其长的脂肪烃链有向垂直于基板表面方向变化的趋势,LB膜与掺杂膜的表面形貌也有明显不同.这表明不同的制备方法可以影响薄膜的结构和形貌.     

乙醇在Ni-Mo合金电极上氧化的动力学模型

利用循环伏安以及稳态极化曲线等方法研究了在１ｍｏｌ．Ｌ＾－１ＫＯＨ溶液中,乙醇在电沉积Ｎｉ－Ｍｏ合金电极上氧化的电化学特性,提出了一个数学模型来预计乙醇在电沉积Ｎｉ－Ｍｏ合金电极上的电化学行为,在碱性溶液中,Ｎｉ（ＯＨ）２／ＮｉＯＯＨ电对的氧化还原过程是乙醇氧化的前期步骤,Ｎｉ（ＯＨ）２／ＮｉＯＯＨ）电对相应的速度常数（即ｋ１和ｋ－１）是电极电位的函数,乙醇氧化是通过一个速度常数为ｋｃ１的化学反应来完成,推导出了各个动力学方程并将实验数据与方程进行比较而获得各个动力学参数,电化学速度常数ｋ１（Ｅ）＝１．４１＊１０＾７ｅｘｐ（０．５ＦＥ／ＲＴ）ｍｍｏｌ．ｃｍ＾－２．ｓ＾－１以及ｋ－１（Ｅ）＝０．７１１ｅｘｐ（０．５ＦＥ／ＲＴ）ｍｍｏｌ．ｃｍ＾－２．ｓ＾－１,Ｅ是相对饱和甘汞电极（ＳＣＥ）的电极电位,而化学反应的速     

Preparation and characterization of [[M(dmb)2]TCNQ.xTCNQo]n polymers (M=Cu,Ag; dmb = 1,8-diisocyano-p-menthane; x = 0, 0.5, 1.0, 1.5; TCNQ = 7,7,8,8-tetracyano-p-quinodimethane) and design of new semi- and photoconducting organometallic materials

New thermoplastic organometallic materials of the type [[M(dmb)2]TCNQ.xTCNQo.y solvent], (M = Cu(I), Ag(I); dmb = 1,8-diisocyano-p-menthane; TCNQ = 7,7,8,8-tetracyano-p-quinodimethane, x = 0, 0.5, 1.0, 1.5; solvent = none, THF or toluene) have been prepared and characterized from X-ray powder diffraction patterns, X-ray crystallography (for some Ag polymers), DSC, and conductivity measurements. While the [[M(dmb)2]TCNQ.xTCNQo]n polymers (M = Cu,Ag; x = 0, 0.5) are insulating, the others (x = 1.0 and 1.5) are semiconducting, and the relative conductivity is found to be a function of the molecular weight and crystallinity. The [[Cu(dmb)2]TCNQ.1.5TCNQ]n material is also photoconducting, while the Ag analogue is not. Photochemical and luminescence quenching experiments in the solid-state established that the Cu+ center and TCNQo act as electron donor and acceptor, respectively, in this photoprocess. Finally photocells of the type glass/SnO2/[Cu(dmb)2]TCNQ.TCNQo]n + 0.5 acceptor/Al (acceptor = TCNQo, C60 and TCNN (13,13,14,14-tetracyano-5,12-naphthacenequinodimethane)) have been designed and characterized. The quantum yields (number of photoproduced electrons/number of photons) are as follows: TCNQ, 1.6 x 10(-4), C60, 5 x 10(-5), TCNN, 3.0 x 10(-4) at lambdaexc = 330 nm. X-ray data for [[Ag(dmb)2]TCNQ.2THF]n: space group P2(1/c), monoclinic, a = 13.5501(10), b = 9.9045(10), c = 32.564(2) A, beta = 91.130(10) degrees, Z = 4. X-ray data for [[Ag(dmb)2]TCNQ.0.5TCNQo.0.5 toluene]n: space group P2(1/c), monoclinic, a = 14.3669(19), b = 9.1659(3), c = 34.012(3) A, beta = 92.140(8) degrees, Z = 4. X-ray data for [[Ag(dmb)2]TCNQ.1.5TCNQo]n: space group C2/c, monoclinic, a = 25.830(11), b = 9.680(2), c = 42.183(19) A, beta = 104.87(4) degrees, Z = 8. X-ray data for [[Ag(dmb)2]DCTC]n: space group P2(1/a), monoclinic, a = 26.273(3), b = 9.730(3), c = 31.526(3) A, beta = 112.12(2)degrees, Z = 4.     

Reactions of SO3 with the O/H radical pool under combustion conditions

The reactions of SO3 with H, O, and OH radicals have been investigated by ab initio calculations. For the SO3 + H reaction (1), the lowest energy pathway involves initial formation of HSO3 and rearrangement to HOSO2, followed by dissociation to OH + SO2. The reaction is fast, with k(1) = 8.4 x 10(9)T(1.22) exp(-13.9 kJ mol(-1)/RT) cm(3) mol(-1) s(-1) (700-2000 K). The SO3 + O --> SO2 + O2 reaction (2) may proceed on both the triplet and singlet surfaces, but due to a high barrier the reaction is predicted to be slow. The rate constant can be described as k(2) = 2.8 x 10(4)T(2.57) exp(-122.3 kJ mol(-1)/RT) cm(3) mol(-1) s(-1) for T > 1000 K. The SO3 + OH reaction to form SO2 + HO2 (3) proceeds by direct abstraction but is comparatively slow, with k(3) = 4.8 x 10(4)T(2.46) exp(-114.1 kJ mol(-) 1/RT) cm(3) mol(-1) s(-1) (800-2000 K). The revised rate constants and detailed reaction mechanism are consistent with experimental data from batch reactors, flow reactors, and laminar flames on oxidation of SO2 to SO3. The SO3 + O reaction is found to be insignificant during most conditions of interest; even in lean flames, SO3 + H is the major consumption reaction for SO3.     

阿司匹林的热解机理及热动力学研究

在用热重法研究了阿司匹林的热稳定性实验的基础上,通过量子化学方法(ab initio DFT)计算了阿司匹林分子的键级,据此计算结果提出了阿司匹林的热解机理,按此机理得到的理论计算值与实验结果一致;运用Freeman-Carroll、Kissinger和Ozawa三种方法分别计算了阿司匹林的热解动力学参数:活化能(E)、反应级数(n)和指前因子(A),其热解动力学方程为: dα/dt=4.74×1011[exp(－(100.34±5.18)×103/RT)](1－α)2.8±0.3;用差示扫描量热法测定的该物质的熔点、摩尔熔化焓和摩尔熔化熵分别为(409.19 ± 0.22) K、(29.17 ± 0.41) kJ•mol-1和(71.09±1.06) J•mol-1•K-1.     

Bimolecular kinetic studies with high-temperature gas-phase 19F NMR: cycloaddition reactions of fluoroolefins

A gas-phase NMR kinetic technique has been used for the first time to obtain accurate measurements of rate constants of some bimolecular, second-order cycloaddition reactions. As a test of the potential use of this technique for the study of second-order reactions, the rate constants and the activation parameters for the cyclodimerization reactions of chlorotrifluoroethylene (CTFE) and tetrafluoroethylene (TFE) were determined in the temperature range 240-340 degrees C, using a commercial high-temperature NMR probe. Obtaining excellent agreement of the results with published data, the technique was then applied to the reaction of 1,1-difluoroallene with 1,3-butadiene, the results of which indicate that the use of gas-phase NMR for reaction kinetics is particularly valuable when a reagent is available only in small amounts and in cases where there are several competing processes occurring simultaneously. The major processes observed in this reaction are regioselective [2+2] and [2+4] cycloadditions, whose rates and activation parameters were determined [k2 = 9.3 x 10(6) exp(-20.1 kcal x mol(-1)/RT) L/mol(-1) x s(-1) and k3 = 1.2 x 10(6) exp(-18.4 kcal x mol(-1)/RT) L/mol(-1) x s(-)(1), respectively] in the temperature range 130-210 degrees C.     

Studies of the kinetics and thermochemistry of the forward and reverse reaction Cl + C6H6 = HCl + C6H5

The laser flash photolysis resonance fluorescence technique was used to monitor atomic Cl kinetics. Loss of Cl following photolysis of CCl4 and NaCl was used to determine k(Cl + C6H6) = 6.4 x 10(-12) exp(-18.1 kJ mol(-1)/RT) cm(3) molecule(-1) s(-1) over 578-922 K and k(Cl + C6D6) = 6.2 x 10(-12) exp(-22.8 kJ mol(-1)/RT) cm(3) molecule(-1) s(-1) over 635-922 K. Inclusion of literature data at room temperature leads to a recommendation of k(Cl + C6H6) = 6.1 x 10(-11) exp(-31.6 kJ mol(-1)/RT) cm(3) molecule(-1) s(-1) for 296-922 K. Monitoring growth of Cl during the reaction of phenyl with HCl led to k(C6H5 + HCl) = 1.14 x 10(-12) exp(+5.2 kJ mol(-1)/RT) cm(3) molecule(-1) s(-1) over 294-748 K, k(C6H5 + DCl) = 7.7 x 10(-13) exp(+4.9 kJ mol(-1)/RT) cm(3) molecule(-1) s(-1) over 292-546 K, an approximate k(C6H5 + C6H5I) = 2 x 10(-11) cm(3) molecule(-1) s(-1) over 300-750 K, and an upper limit k(Cl + C6H5I) < or = 5.3 x 10(-12) exp(+2.8 kJ mol(-1)/RT) cm(3) molecule(-1) s(-1) over 300-750 K. Confidence limits are discussed in the text. Third-law analysis of the equilibrium constant yields the bond dissociation enthalpy D(298)(C6H5-H) = 472.1 +/- 2.5 kJ mol(-1) and thus the enthalpy of formation Delta(f)H(298)(C6H5) = 337.0 +/- 2.5 kJ mol(-1).     

Compressed oxygen in drug stability experiments

A drug stability experiment accelerated by compressed oxygen was established. The stability of 10% ascorbic acid solution as a model was studied and the kinetic parameters were obtained with the newly established experimental method. Because ascorbic acid degrades under both anaerobic and aerobic conditions, the total rate constant k(total) can be expressed as: k(total)=k(anaerobic) + k(aerobic), where k(anaerobic) and k(aerobic) are the rate constants of anaerobic and aerobic degradations, respectively. The k(anaerobic) can be expressed as k(anaerobic) = A(anaerobic) x exp(-E(a,anaerobic)/RT) according to Arrhenius equation, and the k(aerobic) was found to be k(aerobic) = A(aerobic) x exp(-E(a,aerobic)/RT) x p(O2) in our study.     

N-(苯乙酰氨基)-N’-(α-萘乙酰基)硫脲的热解机理及热动力学研究

采用热重法(TG)和微分热重法(DTG)对合成的新型酰氨基硫脲类化合物——N-(苯乙酰氨基)-N’-(α-萘乙酰基)硫脲进行了热稳定性研究, 在25～600 ℃范围内有两次失重过程. 通过量子化学方法计算了分子的Mayer键级, 据此计算结果和热重分析结果提出了其热解机理. 并运用Kissinger和Ozawa等方法计算了其热解动力学参数. 得到第一阶段热解动力学方程为: dα/dt＝541.5exp(－38350/RT)(1－α)2.58; 第二阶段热解动力学方程为: dα/dt＝505.2exp(－64810/RT)&#8226; (1－α)2.12.     

Ab initio study of the ClO + NH2 reaction: prediction of the total rate constant and product branching ratios

The mechanism for ClO + NH2 has been investigated by ab initio molecular orbital and transition-state theory calculations. The species involved have been optimized at the B3LYP/6-311+G(3df,2p) level and their energies have been refined by single-point calculations with the modified Gaussian-2 method, G2M(CC2). Ten stable isomers have been located and a detailed potential energy diagram is provided. The rate constants and branching ratios for the low-lying energy channel products including HCl + HNO, Cl + NH2O, and HOCl + 3NH (X(3)Sigma(-)) are calculated. The result shows that formation of HCl + HNO is dominant below 1000 K; over 1000 K, Cl + NH2O products become dominant. However, the formation of HOCl + 3NH (X(3)Sigma(-)) is unimportant below 1500 K. The pressure-independent individual and total rate constants can be expressed as k1(HCl + HNO) = 4.7 x 10(-8)(T(-1.08)) exp(-129/T), k(2)(Cl + NH2O) = 1.7 x 10(-9)(T(-0.62)) exp(-24/T), k3(HOCl + NH) = 4.8 x 10(-29)(T5.11) exp(-1035/T), and k(total) = 5.0 x 10(-9)(T(-0.67)) exp(-1.2/T), respectively, with units of cm(3) molecule(-1) s(-1), in the temperature range of 200-2500 K.     

Thermochemistry is not a lower bound to the activation energy of endothermic reactions: a kinetic study of the gas-phase reaction of atomic chlorine with ammonia

The rate constant for Cl + NH3 --> HCl + NH2 has been measured over 290-570 K by the time-resolved resonance fluorescence technique. Ground-state Cl atoms were generated by 193 nm excimer laser photolysis of CCl4 and reacted under pseudo-first-order conditions with excess NH3. The forward rate constant was fit by the expression k1 = (1.08 +/- 0.05) x 10(-11) exp(-11.47 +/- 0.16 kJ mol(-1)/RT) cm3 molecule(-1) s(-1), where the uncertainties in the Arrhenius parameters are +/-1 sigma and the 95% confidence limits for k1 are +/-11%. To rationalize the activation energy, which is 7.4 kJ mol(-1) below the endothermicity in the middle of the 1/T range, the potential energy surface was characterized with MPWB1K/6-31++G(2df,2p) theory. The products NH2 + HCl form a hydrogen-bonded adduct, separated from Cl + NH3 by a transition state lower in energy than the products. The rate constant for the reverse process k(-1) was derived via modified transition state theory, and the computed k(-1) exhibits a negative activation energy, which in combination with the experimental equilibrium constant yields k1 in fair accord with experiment.