西南山地煤矿区耕地土壤-农作物重金属富集及健康风险评价

为了解西南某典型山地煤矿区周边农田土壤、农作物重金属的富集情况及对当地人群健康的影响程度,采集矿区周边农田土壤样品和对应的农作物样品,测定重金属Cr、Mn、Zn、As、Pb的含量。运用Nemero指数法、潜在风险指数法对土壤重金属的污染程度进行评价;采用靶标危害系数法(THQ)评价农作物重金属对人体的健康风险。结果显示,Cr、Mn、Zn、As、Pb分别是背景值的1.81、1.90、2.89、1.30、0.86倍,处于轻度污染级别,轻微危害程度。农作物重金属Cr、Pb和As含量的超标情况较严重,Zn的含量超标相对较小。各农作物富集的重金属对人体的健康风险大小为：高粱>玉米>白菜>葱>辣椒。农作物重金属对儿童健康的危害均达到了慢性中毒;对成人健康的影响,高粱处于慢性中毒,其它农作物重金属处于产生较大影响的危害程度。农作物重金属与土壤重金属的相关性分析表明,农作物重金属的含量与土壤重金属全量并无线性关系;各重金属在农作物中的转移能力不同;Pb,As在农作物中的转移能力较大,而Cr相对较小。鉴于矿区重金属的富集情况,应尽快采取修复治理措施,为保证当地人群健康,建议当地居民不再食用和种植富集重金属严重的高粱、玉米农作物。     

Rheology of coal suspensions

Proper design of operations encountered in preparation, transport and employment of suspensions like coal slurries and coal-oil mixtures require an accurate knowledge of their rheological behaviour.Such concentrated suspensions generally exhibit non-Newtonian behaviour (shearthinning) which is more pronounced at higher coal concentrations. The nature of the dispersing medium influences the aggregation state of the disperse phase and, consequently, affects the stability and the rheology of the systems. In the present paper coal suspensions prepared with different dispersing media and covering a wide range in solid phase concentration are studied, by using a rotational coaxial cylinders viscometer.Different models have been taken into consideration for correlating experimental data. In particular, in order to describe the dependence of viscosity on shear rate and solid phase concentration, the suitability of the model suggested by Smith and Bruce is evaluated. Accordingly, the aggregation state of the disperse phase as well as its dependence on shear rate and dispersing medium can be estimated.     

Investigation of operational parameters for an industrial CFB combustor of coal, biomass and sludge

The combustion of coal and/or biomass （sludge, wood waste, RDF, etc.） in a circulating fluidized bed has been a commercial topper for over 20 years, and references to principles and applications are numerous and widespread although few data are presented concerning the operation of large scale CFB-units. The authors studied the CFB-combustion at UPM-Kymmene （Ayr）, a major paper mill relying for its steam production upon the combustion of coal （80-85 %）, wood bark （5-10%） and wastewater treatment sludge （5-10%）. The maximum capacity of the CFB is 58 MWth. A complete diagnostic of the operation was made, and additional tests were performed to assess the operating mode. The plant schematics, relevant dimensions and process data are given. To assess the operation of the UPM-CFB, it is important to review essential design parameters and principles of CFB combustors, which will be discussed in detail to include required data, heat balance and flowrates, operating versus transport velocity, kinetics and conversion （including the possible effect of the Bouduard reaction if carbon is present）. Since the residence time in the riser and the cyclone efficiency determine the burnout of circulating fuel-particles, the UPM-CFB was subjected to a stimulus response technique using nickel oxide as tracer. Results illustrate the efficiency of the cyclone separation and the number of recycle loops for particles of a given size. Results will also be used to assess the cyclone operation and efficiency and to comment upon expected and measured carbon conversion.     

断陷盆地层滑带的发育特征及矿山开发条件下的再变形分析

层滑带在华北断陷盆地中具有普遍性,是影响地下矿山工程围岩稳定的重要因素之一。本文以鲁西矿区为例,阐述了断陷盆地层滑带的发育特征及其形成机制,进行了开挖、运营条件下层滑带再变形分析,并指出了层滑带发育区巷道设计及维护中应注意的某些问题。     

Permeability anisotropy due to consolidation of compressible porous media

The characterisation of flow through porous media is important for all solid–liquid separation and fluid transport realms. The permeability of porous media can be anisotropic and furthermore, the extent of anisotropy can be increased as a result of an applied compressive force. However, the understanding of how anisotropy develops is incomplete. An overview of research on permeability anisotropy is given and an expression for predicting anisotropy as a function of void ratio is offered. The two underlying assumptions of the proposed model are: flow in different directions occurs within the same network of pores and deformation is primarily due to the compression of the particles in the direction of the applied force rather than due to particle rearrangement. The assumption of network connectivity allows permeability anisotropy to be described as a function of flow path tortuosity only. Results are presented for hydraulic anisotropy measured in lignite that has been upgraded by a compression dewatering method known as mechanical thermal expression. The lignite permeability is shown to be up to eight times greater in the direction perpendicular to compression, suggesting that the rate of dewatering could be significantly increased by choosing the drainage to also be perpendicular to the direction of the applied compressive force. It is illustrated that the proposed anisotropy model can be used to accurately predict the experimentally determined permeability anisotropy ratios for lignite, as well as for other materials including sand, clay and kaolin.     

Statistics of reaction progress variable and mixture fraction gradients of a pulverised coal jet flame using Direct Numerical Simulation data

The statistical behaviour of the variances, covariance and gradients of the reaction progress variable (c), and the mixture fraction (ξ) have been analysed in a pulverised coal jet flame using a three-dimensional carrier phase direct numerical simulation (DNS) dataset. It has been observed that the Favre-probability density functions (PDFs) of c and ξ can be parametrised by the standard β function. Furthermore, the log-normal distribution has been found to accurately represent |?c| and |?ξ|. It is also found that ?c and ?ξ remain aligned throughout the flame brush. Finally the joint PDF of |?c| and |?ξ| has been compared with the product of the PDF of |?c| and PDF of |?ξ| extracted from carrier phase DNS, and it has been found that |?c| and |?ξ| are not statistically independent in the case investigated.The bivariate log-normal distributions with and without correlation have also been considered, and the former is found to be in better agreement with the carrier phase DNS data.     

Experimental and numerical investigation of a stagnation pulverised coal flame

A multi-stream Flamelet Progress Variable (FPV) model, specifically developed for coal combustion, is proposed. The model accounts for the different fuel streams associated with the volatile and char burnout products. The applicability of the new FPV model is investigated in a laminar stagnation pulverized coal flame. The flame considered is a premixed mixture of CH₄, O₂ and N₂, carrying pulverized coal particles, stabilized in an impinging wall. Spontaneous emissions of OH*, CH* and C${}_2^{*}$ are measured to identify the flame. The 1D numerical simulations of the experimental conditions are able to reproduce the main features of the flame. The applicability of the multi-stream FPV model to coal combustion is further evaluated with the a posteriori analysis of the FPV results, comparing the results with a reference model, where the species are fully transported and the chemistry directly evaluated. Then, with the budget analysis, the influence of the control variables used to build the look-up table is assessed by examining the conditional contributions to the overall transport terms of scalar quantities (e.g. species, temperature). The results of both analyses show that the proposed multi-stream FPV model can accurately predict the main features of coal combustion, with only minor issues related to the manifold used to build the look-up table.     

Mercury speciation in air-coal and oxy-coal combustion: A modelling approach

In this study, a mechanism for mercury chlorination in flue gases resulting from the combustion of pulverised coal has been presented. Arrhenius parameters of the gas-phase elementary reactions in the Hg–Cl sub-mechanism have been updated and are mainly based on recent experimental and quantum mechanical rate determinations. The mechanism is validated by comparison to accurate experimental data that is unbiased by Hg oxidation in the impinger solutions of aqueous chemistry methods. Solid-phase retention of Hg⁰ has been studied in parallel to char combustion; the heterogeneous model describes condensation of mercury on fly ash particles. The combined homogeneous–heterogeneous model predictions show comparable trends to those of power plant data. This approach aims to provide an improved prediction of mercury speciation from coal-fired power plants and to shed light on the chemical kinetic changes encountered during oxy-coal operation.     

On the rank-dependence of coal tar secondary reactions

The secondary reactions of volatile compounds, including coal tar and light gases, accounts for a great portion of soot formation and the subsequent heat release and pollutant emissions in the combustion zone. While coal primary pyrolysis has been extensively studied over the last few decades and several network pyrolysis models has been developed to describe this process, coal secondary pyrolysis is still not well understood. The Babcock and Wilcox Company has been investigating coal secondary pyrolysis in order to develop a comprehensive mechanism for inclusion in predictive computational fluid dynamics and coal combustion models. Supportive experiments were carried out in an entrained-flow reactor. Tar was extracted from the pyrolysis byproducts of seven coals of widely-distributed rank at temperatures ranging from 923 to 1473 K, and analyzed by ¹³C NMR. Tars formed from higher rank coals generally demonstrated higher sooting propensities. This rank-dependent sooting propensity is associated with tar’s chemical structure properties. With increased heat treatment severity, tar molecules lose a substantial amount of aliphatic attachments, and the average size of substitution per cluster decreases. Compared to tars formed from high-rank bituminous coals, those formed from low-rank sub-bituminous coals have a larger attachment portion, higher averaged substitution, and higher oxygen-containing functional groups. These differences contribute to the higher cracking propensity observed for low-rank coal tars.     

In situ measurements of the spectral emittance of coal ash deposits

The spectral emittance of deposits left by bituminous and sub-bituminous coals under oxidizing conditions have been measured in situ. Pulverized coal is injected into a down-fired entrained-flow reactor. Ash accumulates on a probe in the reactor effluent and radiation emitted by the ash layer is recorded using a Fourier transform infrared (FTIR) spectrometer. Values for the spectral emissive power emitted by the ash and the surface temperature of the ash are extracted from these data. These results are then used to calculate the spectral emittance of the deposit. The spectral emittances of ash deposits formed by burning Illinois #6 (bituminous) coal and Powder River Basin (sub-bituminous) coal were measured between 3000 and 500 wavenumbers. The spectral emittance of the deposit left by the bituminous coal has a constant value of approximately 0.46 between 3000 and 2400 wavenumbers. Between 2200 and 1200 wavenumbers, the spectral emittance of the deposit increases from approximately 0.47 to approximately 0.61. Between 1200 and 500 wavenumbers, the spectral emittance is relatively constant at 0.61. The spectral emittance of the deposit left by the sub-bituminous coal is also relatively constant between 3000 and 2400 wavenumbers at a value of 0.29. Between 2200 and 500 wavenumbers, the spectral emittance of deposits from the sub-bituminous coal increases from approximately 0.29 to 0.55. Differences between these spectral emittance measurements and those measured ex situ illustrate the importance of making in situ measurements. Band emittances were calculated using the measured spectral emittances, and band emittances of the deposits are reported as functions of temperature.