Design assessment of a 150 kWt CFBC Test Unit

For clean and efficient energy generation from coal, the most suitable technology known to date is ‘Fluidized Bed Combustion’ technology. Applications of circulating fluidized bed (CFB) combustion technology have been steadily increasing in both capacity and number over the past decade. Designs of these units have been based on the combustion tests carried out in pilot scale facilities to determine the combustion and desulfurization characteristics of coal and limestone reserves in CFB conditions. Similarly, utilization of Turkish lignites in CFB boilers necessitates adaptation of CFB combustion technology to these resources. However, the design of these test units are not based on firing coals with high ash, volatile matter and sulfur contents like Turkish lignites. For this purpose, a 150 kWt CFB combustor test unit is designed and constructed in Chemical Engineering Department of Middle East Technical University, based on the extensive experience acquired at the existing 0.3 MWt Bubbling Atmospheric Fluidized Bed Combustor (AFBC) Test Rig. Following the commissioning tests, a combustion test is carried out for investigation of combustion characteristics of Çan lignite in CFB conditions and for assessment of the design of test unit. Comparison of the design outputs with experimental results reveals that most of the predictions and assumptions have acceptable agreement with the operating conditions. In conclusion, the performance of 150 kWt CFBC Test Unit is found to be satisfactory to be utilized for the long term research studies on combustion and desulfurization characteristics of indigenous lignite reserves in circulating fluidized bed combustors.     

Numerical investigation of separation efficiency of the cyclone with supercritical fluid–solid flow

The utilization of hydrogen is gaining increasing attention due to its high heating value and environmentally friendly combustion product. The supercritical water circulating fluidized bed reactor is a promising and potentially clean technology that can generate hydrogen from coal gasification. Cyclone is a vital part of the reactor which can separate incomplete decomposition of pulverized coal particles from mixed working fluid. This paper aims to gain in-depth understanding of the cyclone separation mechanisms under supercritical fluid by computational fluid dynamics (CFD). Although the amount of supercritical carbon dioxide in mixed working fluid is minor, it obviously influences the flow fields and separation efficiency of a cyclone. The simulation results suggest that both the decreasing content of supercritical carbon dioxide and adding the extra dipleg cause the promoting performance of cyclones. Research findings could refine the design of supercritical fluid–solid cyclones.     

DEVELOPMENT POTENTIALS AND RESEARCH NEEDS IN CIRCULATING FLUIDIZED BED COMBUSTION

First a report about present status of circulating fluidized bed reactors for coal and multi-fuel combustion in power plants is given. Thereafter the development potentials and research needs for further improvement of CFB combustors operating with finely grained bed materials are discussed and recommendations for direction of further research and development work are presented.     

STUDY ON THE OVERALL PRESSURE BALANCE OF A DOWNFLOW CIRCULATING FLUIDIZED BED SYSTEM

A pressure balance model for a circulating fluidized bed unit that incorporates a downer has been proposed. The model predictions were validated with the experimental data obtained from a special cold-model circulating fluidized bed. Comparison of the operation stability between a CFB downer and a CFB riser has been carried out. Only one critical gas velocity exists in the CFB-riser for a given riser solids flux, while there can be many critical gas velocities for the operation of a CFB downer. Therefore, it is possible to achieve high solids concentration in a CFB downer if appropriate operating conditions are used.     

STUDY ON THE OVERALL PRESSURE BALANCE OF A DOWNFLOW CIRCULATING FLUIDIZED BED SYSTEM

A pressure balance model for a circulating fluidized bed unit that incorporates a downer has been proposed. The model predictions were validated with the experimental data obtained from a special cold-model circulating fluidized bed. Comparison of the operation stability between a CFB downer and a CFB riser has been carried out. Only one critical gas velocity exists in the CFB-riser for a given riser solids flux, while there can be many critical gas velocities for the operation of a CFB downer. Therefore, it is possible to achieve high solids concentration in a CFB downer if appropriate operating conditions are used.     

3D full-loop simulation and experimental verification of gas-solid flow hydrodynamics in a dense circulating fluidized bed

Because of their advantages of high efficiency and low cost, numerical research methods for large-scale circulating fluidized bed （CFB） apparatus are gaining ever more importance. This article presents a numer- ical study of gas-solid flow dynamics using the Eulerian granular multiphase model with a drag coefficient correction based on the energy-minimization multi-scale （EMMS） model. A three-dimensional, full-loop, time-dependent simulation of the hydrodynamics of a dense CFB apparatus is performed. The process parameters （e.g., operating and initial conditions） are provided in accordance with the real experiment to enhance the accuracy of the simulation. The axial profiles of the averaged solid volume fractions and the solids flux at the outlet of the cyclone are in reasonable agreement with experimental data, thereby verifying the applicability of the mathematical and physical models. As a result, the streamline in the riser and standpipe as well as the solids distribution contours at the cross sections is analyzed. Computational fluid dynamics （CFD） serves as a basis for CFB modeling to help resolve certain issues long in dispute but difficult to address experimentally. The results of this study provide the basis of a general approach to describing dynamic simulations of gas-solid flows.     

Investigation on lateral dispersion characteristics of fuel particles in dense phase zone of a large-scale circulating fluidized bed boiler under combustion conditions

The dispersion characteristics of fuel particles in the dense phase zone in circulating fluidized bed (CFB) boilers have an important influence on bed temperature distribution and pollutant emissions. However, previous research in literature was mostly on small-scale apparatus, whose results could not be applied directly to large-scale CFB with multiple dispersion sources. To help solve this problem, we proposed a novel method to estimate the lateral dispersion coefficient (D_x) of fuel particles under partial coal cut-off condition in a 350 MW supercritical CFB boiler based on combustion and dispersion models. Meanwhile, we carried out experiments to obtain the D_x in the range of 0.1218–0.1406 m²/s. Numerical simulations were performed and the influence of operating conditions and furnace structure on fuel dispersion characteristics was investigated, the simulation value of D_x was validated against experimental data. Results revealed that the distribution of bed temperature caused by the fuel dispersion was mainly formed by char combustion. Because of the presence of intermediate water-cooled partition wall, the mixing and dispersion of fuel and bed material particles between the left and right sides of the furnace were hindered, increasing the non-uniformity of the bed temperature near furnace front wall.     

Modeling of particle transport and combustion phenomena in a large-scale circulating fluidized bed boiler using a hybrid Euler-Lagrange approach

The constantly developing fiuidized combustion technology has become competitive with a conventional pulverized coal （PC） combustion. Circulating fluidized bed （CFB） boilers can be a good alternative to PC boilers due to their robustness and lower sensitivity to the fuel quality. However, appropriate engineering tools that can be used to model and optimize the construction and operating parameters of a CFB boiler still require development. This paper presents the application of a relatively novel hybrid Euler-Lagrange approach to model the dense gas-solid flow combined with a combustion process in a large-scale indus- trial CFB boiler. In this work, this complex flow has been resolved by applying the ANSYS FLUENT 14.0 commercial computational fluid dynamics （CFD） code. To accurately resolve the multiphase flow, the original CFD code has been extended by additional user-defined functions. These functions were used to control the boiler mass load, particle recirculation process （simplified boiler geometry）, and interphase hydrodynamic properties. This work was split into two parts. In the first part, which is referred to as pseudo combustion, the combustion process was not directly simulated. Instead, the effect of the chemi- cal reactions was simulated by modifying the density of the continuous phase so that it corresponded to the mean temperature and composition of the flue gases, In this stage, the particle transport was simu- lated using the standard Euler-Euler and novel hybrid Euler-Lagrange approaches, The obtained results were compared against measured data, and both models were compared to each other. In the second part, the numerical model was enhanced by including the chemistry and physics of combustion. To the best of the authors＇ knowledge, the use of the hybrid Euler-Lagrange approach to model combustion is a new engineering application of this model, In this work, the combustion process was modeled for air-fuel combustion. The simulation results were compared with experimental data.     

Particle/Turbulence Interactions, Mass Transfer and Gas/Solid Chemistry in a CFBC Riser

Gas/solid chemistry in the upper, dilute region of a circulating fluidised bed combustor (CFBC) riser is addressed. The limitations of turbulent mixing are illustrated by the example of the heterogeneous NO/CO/char reaction, relevant in CFB combustion of nitrogen-containing solid fuels. The mass transfer of the gaseous reactants to the char surface is determined, and how the conversion is influenced by the degree of mixing of the multiphase system by turbulent dispersion. Particle/turbulence interactions are taken into account by a (Lagrangian) frequency spectrum of velocity fluctuations, which determine the dispersion of the char particles described here with the Tchen–Hinze model. Chars from solid fuels characterised by fuel ratio (FR) ranging from 0.1 (wood) via 0.5 (peat) and 1 (coal A) to 2 (coal B) were considered. The effective rate of the NO/CO/char reaction is determined as a function of the size and type of the char particle, temperature, particle concentration, reactor dimensions and fluidization velocity, at atmospheric pressure. It was found that for this case the effective gas/solid conversion rate in the upper, dilute region of the riser is much lower than the gas/solid chemistry, mainly due to mass transfer limitations for char particles with sizes of typically 300 μm. The concentration of NO at the char particle surface is only a few % of that in the bulk gas phase. Strong influences were found for particle size and temperature, whilst the fluidisation velocity and the reactor size have only a small influence. It is concluded that for a typical CFB riser, for particles larger than approx. 20 μm, mass transfer has a stronger influence on the heterogeneous NO/CO/char reduction mechanism than the ``unmixedness' due to particle eddy dispersion limitations. It is recommended that this or a similar approach to turbulent dispersive mixing is implemented in CFD codes when these are used for boiler and furnace calculations. This revised version was published online in July 2006 with corrections to the Cover Date.     

Non-uniform distribution of gas–solid flow through six parallel cyclones in a CFB system: An experimental study

In large-scale circulating fluidized bed (CFB) boilers, it is common to use multiple cyclones in parallel for the capture of solids, assuming that gas–solid flow to be the same in the cyclones. This article presents a study investigating gas–solid flow through six parallel cyclones in a CFB cold test rig. The six cyclones were located asymmetrically on the left and right walls of the riser. Solid volume fraction and particle velocity profiles at the riser outlets and in the horizontal ducts were measured using a fiber optical probe. Cyclone pressure drop and solid circulating rate were measured for each individual cyclone. Measurements showed good agreement as to the non-uniform distribution of the gas–solid flow, which occurred mainly across the three cyclones on one side: the middle cyclones on both sides had higher particle velocities. Conversely, the solid volume fractions, solid fluxes and solid circulating rates of the middle cyclones were lower than those of the other four cyclones. The apparent reason for the flow non-uniformity among the cyclones is the significant flow non-uniformity at the riser outlets. Under typical operating conditions, the solid volume fractions at the riser outlets had a deviation of up to 26% whereas the solid circulating rates at the stand pipes, 7%. These results are consistent with most other studies in the literature.     

Solids flow diagram of a CFB riser using Geldart B-type powders

Riser operating modes are vital to designing a circulating fluidized bed (CFB) reactor for a required process of either a gas-solid or a gas-catalytic nature. Different operating modes provide different solids’ residence times and mixing behaviors, which define the reactions’ efficiency and yield. The literature demonstrates distinct operating modes resulting from observed differences in slip factors and the range of particle velocities and their associated residence time distribution. The present research uses positron emission particle tracking (PEPT) in a riser of B-type bed material to determine the different operating modes by measuring (i) particle velocities and residence time distribution, (ii) population densities of these particles in the cross-sectional area of the riser, and (iii) solids flow pattern at the bottom of the riser. Data treatment defines four distinct solids hold-up regimes in the riser and proposes a "phase diagram" depicting the existence of the different operating modes (dilute, dense, core-annulus and combined) as a function of the superficial gas velocity and solids circulation flux in the riser. The delineated regimes have good agreement with available literature data and known industrial operations. Comparison with literature data for risers using A-type powders is also fair. The diagram enables CFB designers to better delineate operating characteristics.     

Simulation of mass balance behavior in a large-scale circulating fluidized bed reactor

We determine using a compound model the influence of the mass of granular matter on the behavior of a supercritical circulating fluidized bed (CFB) reactor. Population balance enables a stationary-regime modeling of the mass flow of granular matter inside a CFB unit in a large-scale. The simulation includes some important dynamic processes of gas-particle flows in fluidized bed such as attrition, fragmentation, elutriation, and fuel combustion. Numerical calculations with full boiler loading were performed of operational parameters such as furnace temperature, furnace pressure, feeding materials mass flows, and excess air ratio. Furthermore, three bed inventory masses were adopted as experimental variables in the simulation model of mass balance. This approach enables a sensitivity study of mass flows of granular matter inside a CFB facility. Some computational results from this population balance model obtained for a supercritical CFB reactor are presented that show consistency with the operational data for large-scale CFB units.     

CPFD modeling of hydrodynamics,combustion and NOx emissions in an industrial CFB boiler

The ultra-low NOx emission requirement (50 mg/m³) brings great challenge to CFB boilers in China. To further tap the NOx abatement potential, full understanding the fundamentals behind CFB boilers is needed. To achieve this, a comprehensive CPFD model is established and verified; gas-solid flow, combustion, and NOx emission behavior in an industrial CFB boiler are elaborated; influences of primary air volume and coal particle size on furnace performance are evaluated. Simulation results indicate that there exists a typical core-annular flow structure in the boiler furnace. Furnace temperature is highest in the bottom dense-phase zone (about 950 °C) and decreases gradually along the furnace height. Oxygen-deficient combustion results in high CO concentration and strong reducing atmosphere in the lower furnace. NOx concentration gradually increases in the bottom furnace, reaches maximum at the elevation of secondary air inlet, and then decreases slightly in the upper furnace. Appropriate decreasing the primary air volume and coal particle size would increase the CO concentration and intensify the in-furnace reducing atmosphere, which favors for NOx reduction and low NOx emission from CFB boilers.     

Large Eddy Simulation of a Novel Gas-Assisted Coal Combustion Chamber

In this work a recently presented combustion chamber that is specifically designed for the investigation of gas-assisted coal combustion and the validation of models is simulated under reactive conditions for the first time. In the configuration coal combustion is assisted and stabilized by a methane flame. In the course of the investigation, the configuration’s complexity is increased successively. Results of the isothermal single-phase flow are discussed first. Subsequently, reproducibility of the single-phase methane flame by means of the applied modeling approach is evaluated. In a further step, coal particles having the same thermal power as the methane flame are injected into the configuration. Particle histories, the conversion of the coal particles as well as its retroactive effect on the gas phase are investigated. Experimental results based on laser diagnostics are provided for all operating points and used for comparison with numerical results. Gas phase velocity fields for all operating points are available. In order to identify the reaction in the reactive single-phase case planar laser induced fluorescence of the OH-radical (OH-PLIF) was applied. Overall good agreement between numerical and experimental results could be obtained. In the Large Eddy Simulation (LES) a Flamelet Generated Manifold (FGM) based model is utilized. The four-dimensional manifold is spanned by two mixture fractions, a reaction progress variable and the enthalpy on which the gas phase chemistry gets mapped onto. Thereby, the model accounts for both, volatiles reaction and char conversion. Furthermore, finite rate chemistry effects as well as non-adiabatic physics are considered.     

ANALYSIS ON CYCLONE COLLECTION EFFICIENCIES AT HIGH TEMPERATURES

In order to predict the influence of operating temperature on cyclone performance, an experimental investigation on particle separation was conducted in a 300 mm diameter, tangential volute-inlet and reverse flow cy-clone separator with air heated up to 973 K. The test powder silica has a mean mass diameter of 10 microns and the inlet velocity ranges from 12 m.s-1 to 36 m-s-1. Both the overall efficiency and fractionai efficiency of the cyclone were measured as a function of the inlet velocity and operating temperature. It is shown that at the same inlet velocity both the overall efficiency and fractionai efficiency decrease with an increase of temperature. An analysis of our own data and published results has shown that the fractionai efficiency of a cyclone is a defmite function of such dimensioniess numbers as Stokes number, Reynolds number, Froude number and dimensioniess cyclone inlet area and dimensioniess outlet diameter. A nondimensionai experimental correlation of the cyclone performance, inclu     

Evaluation of the effect of wall boundary conditions on numerical simulations of circulating fluidized beds

A computational fluid dynamics (CFD) modeling of the gas–solids two-phase flow in a circulating fluidized bed (CFB) riser is carried out. The Eularian–Eularian method with the kinetic theory of granular flow is used to solve the gas–solids two-phase flow in the CFB riser. The wall boundary condition of the riser is defined based on the Johnson and Jackson wall boundary theory (Johnson & Jackson, 1987) with specularity coefficient and particle–wall restitution coefficient. The numerical results show that these two coefficients in the wall boundary condition play a major role in the predicted solids lateral velocity, which affects the solid particle distribution in the CFB riser. And the effect of each of the two coefficients on the solids distribution also depends on the other one. The generality of the CFD model is further validated under different operating conditions of the CFB riser.     

Evaluation of the effect of wall boundary conditions on numerical simulations of circulating fluidized beds

A computational fluid dynamics （CFD） modeling of the gas-solids two-phase flow in a circulating fluidized bed （CFB） riser is carried out. The Eularian-Eularian method with the kinetic theory of granular flow is used to solve the gas-solids two-phase flow in the CFB riser. The wall boundary condition of the riser is defined based on the Johnson and Jackson wall boundary theory （Johnson ＆ Jackson, 1987） with specularity coefficient and particle-wall restitution coefficient.The numerical results show that these two coefficients in the wall boundary condition play a major role in the predicted solids lateral velocity, which affects the solid particle distribution in the CFB riser. And the effect of each of the two coefficients on the solids distribution also depends on the other one. The generality of the CFD model is further validated under different operatin~ conditions of the CFB riser.     

THERMAL BOUNDARY LAYER IN CFB BOILER RISER

Measurement of temperature profiles of gas-solid two-phase flow at different heights in commercial-scale circulating fluidized bed (CFB) boilers was carried out. Experimental results showed that the thickness of thermal boundary layer was generally independent of the distance from the air distributor, except when close to the riser outlet. Through analysis of flow and combustion characteristics in the riser, it was found that the main reasons for the phenomena were: 1) the hydrodynamic boundary layer was thinner than the thermal layer and hardly changed along the CFB boiler height, and 2) both radial and axial mass and heat exchanges were strong in the CFB boiler. Numerical simulation of gas flow in the outlet zone confirmed that the distribution of the thermal boundary layer was dominated by the flow field characteristics.     

Comparison of the standard Euler-Euler and hybrid Euler-Lagrange approaches for modeling particle transport in a pilot-scale circulating fluidized bed

Particle transport phenomena in small-scale circulating fiuidized beds （CFB） can be simulated using the Euler-Euler, discrete element method, and Euler-Lagrange approaches. In this work, a hybrid Euler-Lagrange model known as the dense discrete phase model （DDPM）, which has common roots with the multiphase particle-in-cell model, was applied in simulating particle transport within a mid-sized experimental CFB facility. Implementation of the DDPM into the commercial ANSYS Fluent CFD package is relatively young in comparison with the granular Eulerian model. For that reason, validation of the DDPM approach against experimental data is still required and is addressed in this paper. Additional difficulties encountered in modeling fluidization processes are connected with long calculation times. To reduce times, the complete boiler models are simplified to include just the combustion chamber. Such simplifications introduce errors in the predicted solid distribution in the boiler. To investigate the conse- quences of model reduction, simulations were made using the simplified and complete pilot geometries and compared with experimental data. All simulations were performed using the ANSYSFLUENT 14.0 package. A set of user defined functions were used in the hybrid DDPM and Euler-Euler approaches to recirculate solid particles.     

Virtual experimentation through 3D full-loop simulation of a circulating fluidized bed

Eulerian granular multiphase model with a drag coefficient correction based on the energy-minimization multi-male (EMMS) model was used to simulate a semi-industry scale circulating fiuidized bed (CFB).Three-dimensional(3D), time-dependent simulation of a full-loop CFB revealed that the axial profiles of cross-sectionally averaged solid volume fraction,and the radial profiles of solid axial velocity and solid volume fraction were in reasonable agreement with experimental data.Based on this agreement,database derived from experiments not yet accomplished was replenished with such simulations, and fluid regime diagrams and pressure balance around the CFB loop were derived accordingly. This work presents an integrated viewpoint on CFB and unfolds a fresh paradigm fur CFB modeling, which can be expected to help resolve certain issues long in dispute but hard for experiments.