高盐样品中锂的电感耦合等离子体发射光谱法(ICP-OES)测定研究

锂是重要的战略金属和新能源材料,其开发利用受到全球的高度关注。在高盐卤水特别是盐湖卤水和地下卤水中富含巨量的锂资源,在对这些资源进行锂的开发利用过程中,需对锂的含量进行准确测定,然而卤水中共存的高浓度Na+, K+, Ca2+和Mg2+会对微量锂的准确测定产生严重的干扰。电感耦合等离子体发射光谱法(ICP-OES)具有线性范围宽和多元素同步分析能力,针对卤水中锂的快速准确测定,详细开展了高盐样品中锂的ICP-OES分析方法研究。结果表明,锂在610.364 nm处具有较高的信噪比,且Na+, K+, Ca2+, Mg2+和Ar不会对锂的测定产生显著的谱线干扰。然而,样品中大量共存的Na+, K+和Mg2+会对锂的测定产生严重的基体正干扰,而Ca2+产生负干扰。尽管内标法在消除基体干扰方面具有广泛的应用,但传统的以钇和钪为内标元素的内标法不能有效解决该问题。此外,针对标准加入法操作繁琐、不适合批量样品分析问题,以及基体匹配法需多离子匹配,且不适合样品基体组成变化的批量样品分析等问题,考察了采用单一组分进行复杂基体匹配的可行性。由于NaCl广泛存在于卤水中,且对锂的测定具有显著的增敏效应,通过系列研究发现,通过同时向样品和标准溶液中加入10 g·L-1的NaCl,成功解决了总量不超过40 g·L-1的NaCl, KCl和MgCl2所产生的干扰。尽管采用该法或沉淀预分离方式均不能消除Ca2+产生的负干扰,但当样品中Ca2+含量不高于1.8 g·L-1时,对测定不产生显著的影响。通过采用该方法对三种不同基体组成的卤水样品进行加标回收测定,其回收率在96.60%~104.20%范围内。此外,通过与电感耦合等离子体质谱法(ICP-MS)测定结果进行对比,充分论证了该法的准确性和可靠性(相对误差±3.66%)。该法仅以单一的NaCl进行复杂基体匹配,不仅简化了操作,还实现了基体组成变化的批量样品分析,因而在卤水中锂的快速准确测定及锂资源开发利用方面具有重要意义。     

一端弹性支撑的串列双柱和并列双柱在气流中自由端的振幅响应

本文研究了一端弹性支撑的并列双柱和串列双圆柱在气流中自由端的振幅响应，与单圆柱相比，在小间距时，串列双圆柱中前柱的横向振幅受到较强的激励。而在大间距时，振幅受到抑制，特别当Ｌ／Ｄ＝３．５和４．０时，其振幅响应仅为单柱的１／３左右，而对于后柱，则在大间距时，纵向振幅响应有所增大，而且后柱的振幅响应要比前柱的大得多，而并列双圆柱的自由端振幅基本上受到抑制，在Ｔ／Ｄ＞３．０之后，干扰很快减小到接近单个圆     

Interference effects of two and three super-tall buildings under wind action

Most previous investigations on interference effects of tall buildings under wind actions focused on the wind induced interference effects between two buildings,and the interference effects of three or more buildings have seldom been studied so far due to the huge workload involved in experiments and data processing.In this paper,mean and dynamic force/response interference effects and peak wind pressure interference effects of two and three tall buildings,especially the three-building configuration,are investigated through a series of wind tunnel tests on typical tall building models using high frequency force balance technique and wind pressure measurements.Furthermore,the present paper focuses on the effects of parameters,including breadth ratio and height ratio of the buildings and terrain category,on the interference factors and derives relevant regression results for the interference factors.     

连动型抗干扰干涉具井下瓦斯浓度监测系统（英文）

针对井下甲烷浓度监控干扰大的问题,结合实时监测甲烷浓度的系统要求,设计角镜连动的自消震光学结构,构建了基于无线网络的实时数据通信系统.在干涉系统中,固定两个角镜位置,将两片半透半反镜用连杆结构同步旋转,由此产生光程差.由于采用了连杆结构,任意时刻引入的震动在两个分束镜上等量存在,其结果是差分值,可实现完全相消.由分析分束器的最大旋转范围计算得到系统的光程差变化范围.结合比尔朗伯定律,给出系统在井下工作的甲烷气体浓度最低检出限.分别在实验室及矿井主巷道中完成实验过程,通过化学反应法求得被测甲烷气体的标准浓度,与WQF530型光谱分析仪的测试结果作比较,结果表明:在实验室无干扰条件下,两种检测方法的相对误差均小于1.0%;在井下实验中,传统光学检测方法受环境影响明显,相对误差大幅增加,而本系统测试结果基本稳定,具有较强的抗干扰能力及较高的稳定性.     

基于U型弯曲光纤模间干涉的折射率传感

研究了去包层U型弯曲光纤的折射率传感特性.首先根据模间干涉理论,分析了U型光纤传感器的传感原理,指出干涉谱损耗峰波长与环境折射率和弯曲半径有关.利用单模光纤(SM-28)实验制作不同曲率半径的U型光纤传感器,把传感器的U型部分浸入不同折射率的液体中,研究其折射率传感特性.当U型光纤曲率半径为2.5~5.0mm时,传输光谱中均能观察到明显的模间干涉现象;当液体折射率从1.30RIU变到1.43RIU时,光谱损耗峰波长发生红移,且弯曲半径越大,折射率传感灵敏度越高;在曲率半径为5mm时灵敏度为207nm/RIU(折射率1.30~1.40RIU)和1 220nm/RIU(折射率1.40~1.42RIU).干涉峰的波形参量(半高宽、对比度)决定于包层模和纤芯导模之间的比例,当曲率半径为4mm时,损耗峰半高宽最小达3.2nm.综合半高宽和灵敏度两个参量,得出曲率半径4.5mm的U型光纤传感器品质因素最高,分别为43.1RIU-1(折射率1.30~1.40RIU)和191.2RIU-1(折射率1.40~1.42RIU),可直接由SM-28单模光纤制成,且制作工艺简单、成本低、机械强度高不需要任何特殊处理,具有很好的应用前景.     

Resolution improvement for enhancing interference fringes of digital holograms with near infrared illuminance

A new resolution improving method of enhancing the interference stripes, which can achieve better reconstruction of the recorded object of infrared digital holography has been proposed in this paper. The experiment is conducted under near infrared illuminance. We create poor quality holograms with very low-resolution interference stripes and enhance it with our new method. The processed holograms have much higher-resolution interference stripes. This method is based on interpolation theory, and we make it works fast, stable and easy to apply. Both the forward and backward interpolation of the oriental and portrait direction of the source pixels have been calculated, and have been used to realize the final aim of resolution improvement. During the experiment, since the responsivity of the CCD is not satisfied with the illuminance laser, which is by design, we also give specific analysis on the experimental setup of our work to make sure the object information can be fully recorded by the optical setup but cannot be reconstructed because of the low-resolution and unobvious of the interference stripes. After the resolution improvement process of the original hologram, the object information can then be fully reconstructed, which is very clear in the paper. Figures and dataflow give evidence and demonstrate the good performance of our method.     

Computer Controlled AAS Scanning Method to Study Flame Atomization Processes

By slightly changing the optical and burner systems of the conventional atomic absorption spectrometer, a computer controlled scanning method has been developed, which enables us to get a picture of absorbance distribution over the entire cross section of the analytical flames quickly, reproducibly and in high resolution. The plotting of different distribution functions obtainable by computerized data processing and the conclusions drawn from them are illustrated with some examples of flame atomization of cobalt and magnesium salts. The newly discovered method, by its reliability and little demand on time, allows the extension of the general applicability of AAS in revealing analytical interference effects and in the study of flame-chemical processes.     

Cluster speckle structures through multiple apertures forming a closed curve

In this work, cluster-like speckle patterns are analyzed. These patterns are generated when a diffuser illuminated by coherent light is imaged by a lens having a pupil mask with multiple apertures forming a closed curve. We show that the cluster structure results from the complex modulation produced inside each speckle which is generated by multiple interferences of light through the apertures. In particular, when the apertures are uniformly distributed along a closed curve, the resulting image speckle cluster replicates the pupil aperture distribution. Experimental results and theoretical simulations show that cluster features depend on the apertures distribution and the size of the closed curves.     

Design of laser interferometric system for measurement of gear tooth flank

A laser interferometric system (LIS) based on oblique incidence and phase shifting technique has been designed for the measurement of gear tooth flank. For a spur involute gear with a module of 2.0, 60 teeth, and a 20-mm facewidth, some critical parameters of the LIS are calculated, the oblique incidence angle is 84.5°, the beam diameter is 20 mm, and the focal length of imaging lens is 100 mm, and the resolution of CCD camera is 1360 × 1024 pixels. To test the capability of the designed LIS, the numerical simulation is done for the LIS. The actual LIS is built on an optical platform and the experiment is carried out. Both interference fringe patterns from the numerical simulation and the actual experiment are good and coincident with each other, which show the designed LIS is feasible.     

Periodic patterning of silicon by direct nanosecond laser interference ablation

The production of periodic structures in silicon wafers by four-beam is presented. Because laser interference ablation is a single-step and cost-effective process, there is a great technological interest in the fabrication of these structures for their use as antireflection surfaces. Three different laser fluences are used to modify the silicon surface (0.8 J cm⁻², 1.3 J cm⁻², 2.0 J cm⁻²) creating bumps in the rim of the irradiated area. Laser induced periodic surface structures (LIPSS), in particular micro and nano-ripples, are also observed. Measurements of the reflectivity show a decrease in the reflectance for the samples processed with a laser fluence of 2.0 J cm⁻², probably caused by the appearance of the nano-ripples in the structured area, while bumps start to deteriorate.