Yb:CaF2–YF3 transparent ceramics ultrafast laser at dual gain lines

Yb³⁺:CaF₂-YF₃ transparent ceramics with excellent optical quality was successfully fabricated by hot-pressed method. Pulsed laser properties of this ceramics were investigated for the first time. Laser diode (LD) was applied as the pump source to generate a dual-wavelength mode-locked (ML) laser. The maximum average output power was 310 mW, which represents the highest output power of ultrafast calcium fluoride ceramic laser. The spectrum separated at 1048.9 nm and 1049.7 nm with a total pulse duration of 8.9 ps. The interval period between the beating signals was about 4.3 ps, corresponding to a 0.23 THz beat pulse repetition rate. These results demonstrate its potential in producing dual-wavelength ultrashort pulses. These Yb³⁺:CaF₂-YF₃ ceramics with low-cost and short-preparation period are ideal candidate materials for ultrafast lasers.     

Amorphous silicon hexaboride at high pressure

ABSTRACT

We investigate the pressure-induced structural phase transformation of amorphous silicon hexaboride (a-SiB₆) using a constant pressure first principles approach. a-SiB₆ is found to undergo a gradual phase transformation to a high-density amorphous phase (HDA) in which the average coordination number of both B and Si atoms is about 6. The HDA phase consists of differently coordinated motifs ranging from 4 to 8. B₁₂ icosahedra are found to persist during compression of a-SiB₆ and the structural modifications primarily occur around Si atoms and in the regions linking pentagonal pyramid-like configurations to each other. Upon pressure release, an amorphous structure, similar to the uncompressed one, is recovered, indicating a reversible amorphous-to-amorphous phase change in a-SiB_6. When the electronic structure is considered, the HDA phase is perceived to have a wider forbidden band gap than the uncompressed one.     

Eu:Lu2O3透明闪烁陶瓷的制备与性能

采用湿化学法合成了Eu原子掺量5%的Lu₂O₃陶瓷前驱体,通过SEM、XRD研究了煅烧前后前驱体和1 100 ℃煅烧4 h后粉体的形貌、结构以及物相。结果表明煅烧后的粉体为纳米类球形、高分散且结晶性良好的颗粒。颗粒尺寸为68.5 nm。使用煅烧后的粉体为原料,在1 650 ℃真空烧结30 h制备了高透过率的Eu:Lu₂O₃陶瓷,晶粒尺寸为46 μm,在611 nm处的直线透过率可以达到66.3%。此外对陶瓷的吸收曲线、光致激发和发射光谱特性以及X射线激发发射光谱进行研究。可观察到,Eu:Lu₂O₃陶瓷存在基质和激活离子两类吸收,光致发光光谱和X射线激发发射光谱均可以看出Eu:Lu₂O₃陶瓷存在极强的⁵D₀→⁷F₂跃迁发光,位于611 nm处。对比商业的BGO单晶的X射线发射光谱,可得本实验中制备的陶瓷的光输出为85 000 ph/MeV。Eu:Lu₂O₃陶瓷本身有着高X射线以及高能粒子的阻止能力,结合高光输出特性,表明Eu:Lu₂O₃陶瓷在X射线成像等领域具有巨大的潜在应用价值。     

新型BT-BMT-xBNT无铅高储能密度陶瓷研究

本文采用传统固相反应法,成功制备了新型无铅弛豫铁电陶瓷(1-x)[0.9BaTiO₃-0.1Bi(Mg_0.25Ta_0.5)O₃]-xBi_0.5Na_0.5TiO₃。结果表明,较高居里温度的Bi_0.5Na_0.5TiO₃的引入,使得材料体系中建立了更多的以Bi—O耦合为主的极性纳米区域,弥补了因Bi(Mg_0.25Ta_0.5)O₃的加入导致的宏观极化强度的减少,提高了材料的饱和极化强度,实现了较高储能密度的同时具有更好的温度稳定性。在245 kV/cm电场强度下,x=0.2样品的储能密度约为4.01 J/cm³,储能效率约为84.86%,同时该组分在20~170 ℃储能密度的变化率小于5%,储能效率的变化率小于6%,表现出优异的温度稳定性。     

New glass ceramics: an effective conjunction of wet chemistry synthesis and sintering

A glass with CdS nanoparticles was used simultaneously as a matrix for Ce-doped garnet and a yellow-red phosphor to prepare luminescent glass ceramics for the sources of white light. CdS nanoparticles compensate for the unbalanced Ce³⁺ emission spectrum of the composite material due to the addition of a red component. The synthesized composite material can be a tunable light converter due to altered luminescence spectra by changing the sintering conditions and excitation wavelength     

Structure Modification Function of g‐C3N4 for Al2O3 in the In Situ Hydrothermal Process for Enhanced Photocatalytic Activity

Heterojunctions of g‐C₃N₄/Al₂O₃ (g‐C₃N₄=graphitic carbon nitride) are constructed by an in situ one‐pot hydrothermal route based on the development of photoactive γ‐Al₂O₃ semiconductor with a mesoporous structure and a high surface area (188 m²g^?1) acting as electron acceptor. A structure modification function of g‐C₃N₄ for Al₂O₃ in the hydrothermal process is found, which can be attributed to the coordination between unoccupied orbitals of the Al ions and lone‐pair electrons of the N atoms. The as‐synthesized heterojunctions exhibit much higher photocatalytic activity than pure g‐C₃N₄. The hydrogen generation rate and the reaction rate constant for the degradation of methyl orange over 50 % g‐C₃N₄/Al₂O₃ under visible‐light irradiation (λ>420 nm) are 2.5 and 7.3 times, respectively, higher than those over pristine g‐C₃N₄. The enhanced activity of the heterojunctions is attributed to their large specific surface areas, their close contact, and the high interfacial areas between the components as well as their excellent adsorption performance, and efficient charge transfer ability.     

Er~(3+)-Yb~(3+)掺杂SiO_2-SrO-NaF玻璃陶瓷的制备及表征

采用熔融晶化法制备了主晶相为SrF_2的Er~(3+)-Yb~(3+)共掺透明氟氧化物玻璃陶瓷,利用DSC、XRD、SEM、UV-Vis-NIR和荧光光谱对样品的结构、形貌、发光性能进行了测试与表征。研究表明:该体系玻璃最佳热处理温度为620℃,最佳热处理时间为2h,并讨论了Yb~(3+)不同掺杂浓度对Er~(3+)-Yb~(3+)共掺玻璃陶瓷样品上转换发光性能的影响,确定Er~(3+)-Yb~(3+)最佳掺杂浓度比为1∶7,同时观察到了明亮的绿光(522,540 nm)和较弱的红光(656 nm),对Er~(3+)和Yb~(3+)之间的能量传递过程进行了讨论。     

Polymeric materials for lithium‐ion cells

Lithium‐ion (Li‐ion) cells have gained considerable attention in recent years as a power source for various applications owing to their high voltage, high energy density, low self‐discharge, and excellent cycle life. Polymeric materials play a pivotal role in the processing, performance, and safety of Li‐ion cells. The polymeric materials used in Li‐ion cells include: binder for electrode processing, separator, electrolyte, and electrode active material. Active research is being pursued in all of these areas to improve the energy density, power density, cycle life, and safety of Li‐ion cells. This review article gives an overview of the various polymeric materials used in Li‐ion cells and the recent advances in these materials. Copyright © 2017 John Wiley & Sons, Ltd.     

ELECTROELASTIC FIELD FOR AN IMPERMEABLE ANTI-PLANE SHEAR CRACK IN A PIEZOELECTRIC CERAMICS PLATE

ＩｎｔｒｏｄｕｃｔｉｏｎＤｕｅｔｏｔｈｅｉｎｔｒｉｎｓｉｃｃｏｕｐｌｉｎｇｃｈａｒａｃｔｅｒｉｓｔｉｃｓｂｅｔｗｅｅｎｅｌｅｃｔｒｉｃａｎｄｅｌａｓｔｉｃｂｅｈａｖｉｏｒｓ,ｔｈａｔｉｓ,ａｐｐｌｉｅｄｍｅｃｈａｎｉｃａｌｌｏａｄｉｎｇｐｒｏｄｕｃｅｓｅｌａｓｔｉｃｄｅｆｏｒｍａｔｉｏｎ ,ａｓｗｅｌｌａｓｅｌｅｃｔｒｉｃｆｉｅｌｄ ,ａｎｄｃｏｎｖｅｒｓｅｌｙｅｌｅｃｔｒｉｃｆｉｅｌｄｃａｎｇｉｖｅｒｉｓｅｔｏｅｌａｓｔｉｃｄｅｆｏｒｍａｔｉｏｎ ,ｐｉｅｚｏｅｌｅｃｔｒｉｃｍａｔｅｒｉａｌｓｈａｖｅ…     

Fourier transform mechanical spectroscopy of the sol-gel transition in zirconium alkoxide ceramic gels

The gelation of a ceramic precursor, zirconium alkoxide, has been studied using dynamic oscillatory measurements. The gelation time is controlled by varying the concentrations of zirconium propoxide, hydrolysis with water, and acetylacetone concentration which acts as a chelating ligand. Gelation times were varied from minutes to months. The gelation time varied with zirconium concentration to the –10 power, hydrolysis to the –7 power, and ligand concentration of the –17 power. The sol-gel transition was monitored using the criteria of Winter in which GG ⁿ and tan () = tan . It is shown that the use of multiple superimposed sinusoidal waves to simultaneously measure the moduli at several frequencies is faster than using individual frequency sweep experiments. The selection of rate and strain criteria for brittle network gels is discussed in detail.