多孔TiO2负载Pt的制备及室温下催化降解甲醛的研究

以钛酸丁酯为前驱物,通过水解-水热法,成功制备了多孔TiO2,以此为载体,通过化学还原法负载Pt,制得Pt/TiO2复合催化剂.采用XRD、SEM、TEM、N2吸附-脱附等方法对样品的理化性能进行表征,以HCHO为目标污染物,测试了Pt/TiO2催化剂的室温催化活性.实验结果表明:水热处理对样品的微观结构和催化活性有很大影响,水热处理有助于TiO2晶体化,形成层次丰富和形状规则的孔道体系,有助于Pt的分散负载和污染物分子的扩散流通.以多孔TiO2作为载体的催化剂比以P25作为载体的催化剂具有更高的催化活性,多次循环测试,Pt/TiO2催化剂仍具有较高的稳定性.     

焊后热处理对聚变堆用奥氏体不锈钢MAG焊焊缝金属冲击韧性的影响

After heat treatment of metal active gas arc welding (MAG weld) joints of 316LN austenitic stainless steel for fusion reactor at different temperatures, Charpy impact test at liquid nitrogen temperature was carried out. The effects of heat treatment temperature on microstructure, fracture morphology and precipitates were studied with optical microscope, SEM and EDS analysis. Results indicated that the impact toughness of weld metal could be significantly improved by 873K heat treatment. However, with the rising of heat treatment temperature, the precipitates were generated gradually along the grain boundary and a gradual decrease of toughness occurred as well. All fracture was ductile. The dimple became shallow and less with the increase of temperature. Spherical and irregular precipitates were found at the bottom of the dimple. The spherical precipitates generated during welding were free from the influence of the heat treatment, and the irregular precipitates increased with the rising of temperature. High content of Mo in filler materials led to a great segregation of Mo at the grain boundary, which would promote the precipitation of σ phase. Impact toughness of weld metal decreased significantly when continuous distribution of σ phase formed at grain boundary.     

过渡金属Co2+离子掺杂ZnS硫化物纳米晶制备与中红外发光特性研究

利用不含有机相的简单水热法制备了Co^2+∶ZnS纳米晶,纳米晶具有立方闪锌矿结构,平均晶粒尺寸约为8.3 nm,在808 nm激光泵浦下具有2~5μm波段的中红外荧光发射,中心波长位于3400 nm和4700 nm,分别对应Co^2+离子的4T2(F)→4 A 1(F)和4T1(F)→4T2(F)的能级跃迁.进一步将制备的纳米晶在还原气氛下进行800℃热处理,获得立方闪锌矿和纤锌矿混合晶型的纳米晶,平均晶粒尺寸增大到22.5 nm左右,热处理后的纳米晶表面羟基含量更低,中红外荧光发射强度显著提高.该Co^2+∶ZnS纳米晶的制备方法简单、在制备过程中不引入有机相等荧光淬灭中心,同时证明通过后热处理过程可以进一步减少表面缺陷及羟基含量,使荧光强度得到大幅提升.     

无溶剂热处理固相转化法简易制备沸石咪唑酯骨架材料

设计开发了一种无需溶剂，通过热处理固相转化制备沸石咪唑酯骨架材料（ZIFs）的简易方法.该方法无需溶剂及其它预处理，只需将金属源与有机配体固相混合后于低温（200℃）热处理即可实现多孔晶体材料的制备.所合成材料H-ZIF-67为具有方纳石拓扑结构的纳米晶体，与传统方式合成的ZIFs材料一致.粉末X射线衍射（PXRD）分析结果表明产物的晶体结构与标准ZIFs谱图一致.通过扫描电子显微镜（SEM）、透射电子显微镜（TEM）、N₂吸附-脱附分析、热重分析（TGA）和傅里叶变换红外光谱（FTIR）等手段对合成的材料进行了表征，发现H-ZIF-67材料具有与ZIFs材料类似的特性.该方法经济、高效，摒弃了传统方法合成ZIFs材料周期长、处理过程复杂的弊端，为ZIFs材料的量产提供了新思路.     

热处理对CH薄膜表面粗糙度及力学性能的影响

利用低压等离子体化学气相沉积法制备厚度约为7μm的辉光放电聚合物薄膜,将制备的薄膜样品放入通有氩气保护的热处理炉中加热至300℃,分别进行6,10,24h的保温热处理。通过白光干涉仪观察分析了不同保温时间下辉光放电聚合物薄膜的表面粗糙度;利用傅里叶变换红外吸收光谱分析了300℃条件下不同保温时间对薄膜结构的影响;采用纳米压痕仪表征了不同保温时间热处理后,薄膜硬度及模量的变化。结果表明:随着保温时间的增加,薄膜的表面均方根粗糙度由12nm降至4.43nm。薄膜结构中甲基的相对含量减少,双键的相对含量增加,碳链变长,同时薄膜网络结构的交联化程度增强。硬度和模量随着保温时间的增加先减小后增大。     

热处理对NiTi形状记忆合金冲蚀磨损性能的影响

采用自制浆罐式砂水冲蚀磨损试验装置研究了4种经不同条件热处理的NiTi合金与1Cr18Ni9Ti不锈钢的冲蚀磨损性能;采用XL-30型扫描电子显微镜观察试样的冲蚀磨损表面形貌;采用MH-6型显微硬度计测量NiTi合金硬度;采用自制拉伸装置测量NiTi合金的力学性能.结果表明:5种试样的冲蚀磨损量随着冲蚀时间、冲蚀速度、砂水比及砂粒度的增加而增大,4种NiTi合金的耐冲蚀性能相近,均明显优于1Cr18Ni9Ti不锈钢,其中试样NiTi-3和NiTi-1表现出较好的耐冲蚀性能;硬度并非NiTi合金冲蚀磨损性能的决定因素,超弹性和超塑性是NiTi合金具有较好耐冲蚀性的主要原因,热处理使得NiTi合金的超弹性变形量减小,但增加了NiTi合金的塑性变形量;合金丝磨损表面不同部位的磨损机理不同,中部为典型的变形磨损,侧面为微切削磨损,5种试样均表现为典型的韧性材料冲蚀磨损特征.     

钛表面生物活性榍石/氧化钛复合涂层的结构和磷灰石形成机理

采用微弧氧化和热处理复合技术,在钛表面制备了具有双层结构的榍石/氧化钛复合涂层。榍石/氧化钛复合涂层的外层是由微弧氧化涂层经热处理后晶化生成;而内层是由钛基底的氧化生成,并且氧化钛表现出不同的Ti,O原子比。由于钛基底的氧化,孔径在50~500nm的微孔呈层状结构分布在涂层内层。与微弧氧化涂层相比,该复合涂层具有很好的磷灰石诱导能力,这是由于榍石沿着特定晶面和晶向与羟基磷灰石表现出良好的晶体学匹配关系,从而为磷灰石的成核和取向沉积过程提供良好的位点。     

Short range order transformation and magnetostriction of Fes3Ga17 ribbons

The relationship between magnetostriction and structure of melt-spun Fes3Ga17 ribbons are investigated by XRD and M5ssbauer spectrum technique （MS）. As the heat-treatment temperature increases from 650℃ to 800℃, the magnetostriction coefficient of Fes3Ga17 ribbon first increases and then decreases. The largest magnetostriction coeiffcient （-578.4 ppm） is achieved in those specimens quenched at 750oc. According to the XRD and MSssbauer spectrum anal- ysis, a small quantity of DO3 phase is precipitated in Fe83Ga17 ribbons when quenched from 650℃ and the DO3 phase is gradually transformed into B2-1ike phase if quenched at higher temperature. However, both DO3 and B2-1ike phases disappear when the temperature increases up to 800℃. From this point of view, B2-1ike phase might be beneficial to the enhancement of magnetostrictive properties of melt-spun ribbons.