多模式离子推力器输入参数设计及工作特性研究

针对我国小行星探测任务对电推进系统离子推力器设计要求,基于等离子体基本理论建立了多模式离子推力器输入参数与输出特性关系,完成各工作点下屏栅电压、束电流、阳极电流、加速电压,流率等输入参数设计,采用试验研究和理论分析的方法研究了推力器工作特性.试验结果表明:在设计输入参数下,23个工作点推力最大误差小于3%,比冲最大误差小于4%,在功率为289—3106 W下,推力为9.7—117.6 mN,比冲为1220—3517 s,效率为23.4%—67.8%,电子返流极限电压随着推力增加单调减小,最小、最大推力下分别为-79.5 V和-137 V,放电损耗随着功率增大从359.7 W/A下降到210 W/A,并在886 W时存在明显拐点,效率随功率增大而上升,在1700 W后增速变缓并趋于稳定,在轨应用可综合推力器性能、任务剖面要求、寿命,合理设计输入参数区间,制定控制策略.     

基于电化学老化衰退模型的锂离子动力电池外特性

当前锂离子动力电池电化学模型存在模型复杂、建模难度大、计算效率低、老化评估效果差的问题,本文提出一种考虑电池衰退老化的机理模型(ADME).本文首先通过有限差分法对伪二维(P2D)电化学模型进行离散降阶处理,得到简化伪二维(SP2D)模型.在SP2D模型的基础上,基于阴阳两极发生的副反应导致的衰退老化现象,提出一种考虑电池衰退老化的机理模型.其次,使用多变量偏差补偿最小二乘法实现模型参数辨识.最后通过动力电池衰退老化性能循环实验,对比分析了恒流、脉冲工况下SP2D模型和ADME模型的终端电压输出.结果表明:ADME模型较为简单、计算效率和估算精度高,可以有效评估电池容量老化衰退,得到理想的锂离子动力电池外特性曲线.     

光纤基底TiNi形状记忆合金薄膜制备工艺

将TiNi基记忆合金薄膜与光纤相结合可制成智能化、集成化且成本经济的微机电系统和微传感器件.本文采用磁控溅射法在二氧化硅光纤基底上制备TiNi记忆合金薄膜,系统讨论了溅射工艺参数以及后续退火处理对薄膜质量的影响.采用自研制光纤镀膜掩膜装置在直径为125μm的光纤圆周表面上形成均匀薄膜.实验表明:在靶基距、背底真空度、Ar气流量和溅射时间一定的条件下,溅射功率存在最佳值;溅射压强较大时,薄膜沉积速率较低,但薄膜表面粗糙度较小.进行退火处理后,薄膜形成较良好的晶体结构,Ti_49.09Ni_50.91薄膜中马氏体B19′相和奥氏体B2相共存,但以B19′为主.根据本文研究结果,在玻璃光纤基底上制备高质量的TiNi基记忆合金薄膜是可实现的,本工作为下一步研制微机电系统和微型传感器做了基础准备.     

全局优化问题的一个新的无参数填充函数

求全局最优化问题的填充函数算法被提出以来，参数的选取和调整一直是制约算法有效性的因素。如何在实际的计算过程中选取合适的参数，直接影响和决定了运算速度和效率。因此，构造不含参数的填充函数就显得极为重要。提出一个新的无参数的填充函数，对其理论性质进行了分析，并给出相应的填充函数算法，数值计算验证了算法的有效性。     

基于遗传算法的紧凑型高温超导托卡马克磁体优化

基于遗传算法和二维轴对称磁场有限元模型对高温超导托卡马克装置磁体进行了优化设计。以超导带材使用量最少为优化的目标函数，在给定的背景场设计指标和高温超导带材在50K、不同背景场的临界电流数据下，对磁体物理参数以及运行电流进行优化，得到了托卡马克高温超导磁体在50K温区下的设计方案。     

基于NiCo2O4纳米片电极的非对称混合电容器

The looming global energy crisis and ever-increasing energy demands have catalyzed the development of renewable energy storage systems. In this regard, supercapacitors (SCs) have attracted widespread attention because of their advantageous attributes such as high power density, excellent cycle stability, and environmental friendliness. However, SCs exhibit low energy density and it is important to optimize electrode materials to improve the overall performance of these devices. Among the various electrode materials available, spinel nickel cobaltate (NiCo₂O₄) is particularly interesting because of its excellent theoretical capacitance. Based on the understanding that the performances of the electrode materials strongly depend on their morphologies and structures, in this study, we successfully synthesized NiCo₂O₄ nanosheets on Ni foam via a simple hydrothermal route followed by calcination. The structures and morphologies of the as-synthesized products were characterized by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis, and the results showed that they were uniformly distributed on the Ni foam support. The surface chemical states of the elements in the samples were identified by X-ray photoelectron spectroscopy. The as-synthesized NiCo₂O₄ products were then tested as cathode materials for supercapacitors in a traditional three-electrode system. The electrochemical performances of the NiCo₂O₄ electrode materials were studied and the area capacitance was found to be 1.26 C·cm^-2 at a current density of 1 mA·cm^-2. Furthermore, outstanding cycling stability with 97.6% retention of the initial discharge capacitance after 10000 cycles and excellent rate performance (67.5% capacitance retention with the current density from 1 to 14 mA·cm^-2) were achieved. It was found that the Ni foam supporting the NiCo₂O₄ nanosheets increased the conductivity of the electrode materials. However, it is worth noting that the contribution of nickel foam to the areal capacitance of the electrode materials was almost zero during the charge and discharge processes. To further investigate the practical application of the as-synthesized NiCo₂O₄ nanosheets-based electrode, a device was assembled with the as-prepared samples as the positive electrode and active carbon (AC) as the negative electrode. The assembled supercapacitor showed energy densities of 0.14 and 0.09 Wh·cm^-3 at 1.56 and 4.5 W·cm^-3, respectively. Furthermore, it was able to maintain 95% of its initial specific capacitance after 10000 cycles. The excellent electrochemical performance of the NiCo₂O₄ nanosheets could be ascribed to their unique spatial structure composed of interconnected ultrathin nanosheets, which facilitated electron transportation and ion penetration, suggesting their potential applications as electrode materials for high performance supercapacitors. The present synthetic route can be extended to other ternary transition metal oxides/sulfides for future energy storage devices and systems.     

基于响应面法的直拉硅单晶生长工艺参数优化方法

在直拉法制备硅单晶的过程中,要得到优质的晶体必须建立合理的温度分布,而单晶炉内热场的分布与工艺参数的设定密切相关.其中以晶体转速、坩埚转速和拉速等三个工艺参数对热场分布的影响尤为显著.为了确定最佳热场分布下晶转、埚转及拉速的设定值,本文采用响应面算法通过方程拟合、回归分析等步骤求解这三个工艺参量与温度梯度之间的最佳函数模型,并在该模型下同时对这三个工艺参量进行优化分析,且通过仿真实验和拉晶实验表明该方法的有效性.     

求解矩阵方程AXB+CXD=F参数迭代法的最优参数分析

本文针对求矩阵方程AXB+CXD=F唯一解的参数迭代法，分析当矩阵A，B，C，D均是Hermite正（负）定矩阵时，迭代矩阵的特征值表达式，给出了最优参数的确定方法，并提出了相应的加速算法.     

高居里温度铁电单晶PIN-PT的机电性能

弛豫铁电单晶Pb(In_1/2Nb_1/2)O₃-PbTiO₃(PIN-PT)相较于常用的Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃(PMN-PT)具有更高的居里温度,在高稳定性、高性能的传感器、换能器方面具有应用前景。本工作采用谐振法研究了[001]方向极化的0.66PIN-0.34PT铁电单晶的全矩阵机电性能参数。0.66PIN-0.34PT 单晶的三方-四方相变温度(T_RT)约为160 ℃,居里温度(T_C)约为260 ℃,室温压电系数d₃₃、d₃₁、d₁₅分别为1 340 pC/N、-780 pC/N、321 pC/N,介电常数ε^T₃₃、ε^S₃₃、ε^T₁₁、ε^S₁₁分别为2 700、905、2 210、1 927,机电耦合系数 k₃₃、k₃₁、k₁₅、k_t分别为 87%、58%、38%、61%。其纵向压电常数(d₃₃)和纵向机电耦合系数(k₃₃)小于 PMN-PT 单晶,但是横向压电性能(d₃₁)和剪切压电性能(d₁₅)都略高于PMN-PT单晶。另外,研究了机电耦合性能随温度的变化趋势,发现0.66PIN-0.34PT单晶在150 ℃以下有较好的温度稳定性。