Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

环状连续强激光下光学薄膜的瞬温和热畸变

详细研究了非冷却光学薄膜元件在环形激光光束辐照下的瞬态温度分布和随后的热畸变，并且用泰曼干涉仪实际测量了连续波氧碘激光辐照各种非冷却光学元件的热畸变量并与理论计算相比较，分析结果表明理论和实验相一致。     

A study of structural, compositional and optical properties of spray-deposited non-stoichiometric (Zn,Fe)S thin films

Non-stoichiometric ternary chalcogenides (Zn,Fe)S were prepared in the film form by pyrolytic spray deposition technique, using air/nitrogen as the carrier gas. The precursor solution comprised of ZnCl₂, FeCl₂ and thiourea. The depositions were carried out under optimum conditions of experimental parameters viz. carrier gas (air/nitrogen) flow rate, concentration of precursor constituents, nozzle substrate distance and temperature of quartz substrate. The deposited thin films were later sintered in argon at 1073 K for 120 min.The structural, compositional and optical properties of the sintered thin films were studied. X-ray diffraction studies of the thin films indicated the presence of (Zn,Fe)S solid solution with prominent cubic sphalerite phase while surface morphology as determined by scanning electron microscopy (SEM) revealed a granular structure.The chemical composition of the resulting thin films as analyzed by energy dispersive X-ray analysis (EDAX) reflected the composition of the precursor solutions from which the depositions were carried out with Fe at% values ranging from 0.4 up to 33.SEM micrographs of thin films reveal that the grain sizes of the thin films prepared using air as carrier gas and N₂ as carrier gas are in the vicinity of 300 and 150 nm, respectively.The diffuse transmittance measurements for thin films, as a function of wavelength reveal the dependence of direct optical band gap on Fe content and type of phase.     

Electrical properties and Schottky diodes using N-N′diphenyl-1-4phenylenediamine

Thin films of, N-N′diphenyl 1-4phenylene-diamineane are prepared using vacuum sublimation technique. The electrical conductivity from room temperature down to 127 K is studied. It is found that the conduction of charge carriers obeys T^−1/2 dependence on temperature. The average hopping distance, hopping energy, density of states and their variation due to post-deposition heat treatment are studied. Schottky diodes are fabricated with gold as ohmic contact and aluminium as Schottky contact. From the observed current voltage characteristics the saturation current density, diode ideality factor and the barrier height are determined. Their variation with air annealing is also investigated.     

工作气压对电子束沉积ZrO2薄膜折射率和聚集密度的影响

采用电子束蒸发的方法，用石英晶体振荡法监控薄膜的蒸发速率，在不同工作气压下制备了ZrO2薄膜样品.在相调制型椭圆偏振光谱仪和分光光度计上对样品的光谱特性进行了测试.根据波长漂移的理论，计算出薄膜的聚集密度.结果表明，随着工作气压的降低，薄膜的聚集密度和折射率都随之增大.     

双涂层光纤应变传感器的理论与实验研究

对带有聚合物涂敷层和缓冲层的光纤应变传感器的力学特性进行了研究，建立了双涂层光纤与基体材料相互作用的线弹性理论模型.理论研究表明：在小半径近似条件下，双涂层光纤的力学传递特性决定于涂覆层和缓冲层的弹性模量的相对值；当缓冲层的弹性模量远大于涂覆层时，其作用可忽略.实验中，将光纤传感器埋入基体材料内部，利用白光干涉应变测量方法，对平均应变传递系数进行了实验研究.实验结果与理论仿真具有较好的一致性.     

Indirect Methods For Determination of The Protective Effects of Coating Films on The Surface of Crystals

The extents of the protective effects of coating films on the surface of crystals were determined. Three different samples were made with different quantities of coating fluid (Sepifilm LP 010 in 10% aqueous solution). Since the atomizing rate was constant, the coating time increased in parallel with the volume of coating fluid applied. The direct measurement of film thickness and smoothness is very difficult, and therefore indirect methods were used. Dimenhydrinate was chosen as model drug; this is a heat-sensitive antihistamine with a low melting point. This temperature can be reached during the tableting process. The behaviour of samples on exposure to heat was examined by differential scanning calorimetry. The water uptakes of the samples were determined with an Enslin apparatus. Plasticity was studied with an instrumented tablet machine. These indirect methods (thermal conductivity, water uptake and plasticity measurements) revealed connections between the results of the various experiments. An overlong coating time decreased the protective effect of the coating film. This revised version was published online in August 2006 with corrections to the Cover Date.     

Noise-assisted mound coarsening in epitaxial growth

Two types of mechanisms are proposed for mound coarsening during unstable epitaxial growth: stochastic, due to deposition noise, and deterministic, due to mass currents driven by surface energy differences. Both yield the relation H=(RWL)² between the typical mound height W, mound size L, and the film thickness H. An analysis of simulations and experimental data shows that the parameter R saturates to a value which discriminates sharply between stochastic () and deterministic () coarsening. We derive a scaling relation between the coarsening exponent 1/z and the mound-height exponent which, for a saturated mound slope, yields . Received: 11 November 1997 / Revised in final form: 28 November 1997 / Accepted: 28 November 1997     

Optimal design of a convergent-barrel cold spray nozzle by numerical method

A convergent-barrel (CB) cold spray nozzle was designed through numerical simulation. It was found that the main factors influencing significantly particle velocity and temperature include the length and diameter of the barrel section, the nature of the accelerating gas and its pressure and temperature, and the particle size. Particles can achieve a relatively low velocity but a high temperature under the same gas pressure using a CB nozzle compared to a convergent-divergent (CD) nozzle. The experiment results with Cu powder using the designed CB nozzle confirmed that particle deposition can be realized under a lower gas pressure with a CB nozzle.