Interface and defects engineering for multilayer laser coatings

High-reflective multilayer laser coatings are widely used in advanced optical systems from high power laser facilities to high precision metrology systems. However, the real interface quality and defects will significantly affect absorption/scattering losses and laser induced damage thresholds of multilayer coatings. With the recent advances in the control of coating design and deposition processes, these coating properties can be significantly improved when properly engineered the interface and defects. This paper reviews the recent progress in the physics of laser damage, optical losses and environmental stability involved in multilayer reflective coatings for high power nanosecond near-infrared lasers. We first provide an overview of the layer growth mechanisms, ways to control the microstructures and reduce layer roughness, as well as the nature of defects which are critical to the optical loss and laser induced damage. Then an overview of interface engineering based on the design of coating structure and the regulation of deposition materials reveals their ability to improve the laser induced damage threshold, reduce the backscattering, and realize the desirable properties of environmental stability and exceptional multifunctionality. Moreover, we describe the recent progress in the laser damage and scattering mechanism of nodule defects and give the approaches to suppress the defect-induced damage and scattering of the multilayer laser coatings. Finally, the present challenges and limitations of high-performance multilayer laser coatings are highlighted, along with the comments on likely trends in future.     

Defects related emission and nanosecond optical power limiting in CuS quantum dots

We report optical and nonlinear optical properties of CuS quantum dots and nanoparticles prepared through a nontoxic, green, one-pot synthesis method. The presence of surface states and defects in the quantum dots are evident from the luminescent behavior and enhanced nonlinear optical properties measured using the open aperture Z-scan, employing 5 ns laser pulses at 532 nm. The quantum dots exhibit large effective third order nonlinear optical coefficients with a relatively lower optical limiting threshold of 2.3 J cm⁻², and the optical nonlinearity arises largely from absorption saturation and excited state absorption. Results suggest that these materials are potential candidates for designing efficient optical limiters with applications in laser safety devices.     

Curvature investigation in tapered fibers and its application to sensing and mode conversion

Non-adiabatic tapered fibers are basic photonic components used in a wide range of applications. Here we investigate a way to increase their utility through the controllable bending of one of their tapered sections. The experiments carried out explain, for the first time, the mechanics of this approach showing how these tapers can be used to build more sensitive sensors. Their use as highly efficient mode converters is also discussed.     

TBOR-shaped electro-optic modulator with dual output based on double-layer graphene

We proposed an electro-optic modulator with two-bus one-ring (TBOR) structure to improve the extinction ratio and reduce insert loss. It has a dual output compared with one-bus one-ring structure. In addition, double-layer graphene makes it possible for the modulation in the visible to mid-infrared wavelength range. It shows that this new electro-optic modulator can present two switching states well with low insertion loss, high absorption and high extinction ratio. At $\lambda =1550\text{ nm}$, when the switching states are based on the chemical potential, ${\mu }_{\mathrm{c}}=0.38\text{ eV}$ and ${\mu }_{\mathrm{c}}=0.4\text{ eV}$, the insertion losses of both output ports are less than 2 dB, the absorption of the output port coupled via a micro-ring reaches 45 dB and the extinction ratio reaches 14 dB. When the refractive index of the dielectric material is 4.2, the applied voltage will be less than 1.2 V, thus can be used in low-voltage CMOS technology.     

Controlled synthesis of ZnO nanoparticles from a Zn(II) coordination polymer: Structural characterization,optical properties and photocatalytic activity

A zinc coordination polymer derived from pyridine-2,6-dicarboxylate (PDC), {[Zn₂(PDC)₂]}_n, was successfully prepared via conventional, sonication and microwave-irradiation methods. The composition and characteristics of the obtained coordination polymers (CPs) were investigated by elemental analysis, TGA/DTA, X-ray diffraction and spectroscopic techniques. The so obtained CPs were heat-treated in the air at 600 °C for 2 h to produce ZnO of nanosized particles (NPs). It is of interest to note that the synthesis approach of the precursor greatly affects both the nanoparticle size and the structure of the resulting ZnO NPs. Moreover, the smallest particle size was associated with the sample derived from the ultrasonically prepared precursor. TEM analysis revealed that all samples have sphere-like morphologies. Structural analysis of the prepared ZnO samples was conducted and compared using Rietveld analysis of their PXRD patterns. Optical band gap calculations based on analysis of the UV–vis spectra of ZnO samples using Tauc's power law were achieved. The highest band gap of 3.63 eV was observed for ZnO sample obtained from the ultrasonically prepared precursor. Furthermore, the photocatalytic activity of ZnO NPs for the removal of Eosin Y color was monitored. The highest removal efficiency was recorded for ZnO originated from the ultrasonically synthesized precursor. Enhancement of removal efficiency that reached 98% was attained in only a period of 8 min. Its recycling test showed that it can be reused without structural changes over four cycling experiments.     

非线性光纤方向耦合器孤子动力特性分析

利用变分方法,导出了双曲正割型光孤子在非线性光纤耦合器中传输时满足的动力学方程组,分析了该方程组的平衡点性态,讨论了光孤子的开关特性.指出参数|β|<2π.是能实现完全的开关操作的必要条件.     

微球动态涂敷状态实时监测光学系统的设计

 介绍了一种可用于实时监测直径0.2～1.0 mm激光核聚变靶球涂敷状态的光学系统的设计，系统采用环形LED照明系统以适合特殊的照明要求，用Petzval型物镜使500 mm处的微球清晰成像于CCD像面上，CCD输出的图像电信号经图像采集卡转换成数字信号，最后该数字信号由计算机进行处理，实现了系统对靶球膜层涂敷作业的自动监控，大大提高了涂敷效率。所设计的系统轴上点最大弥散斑直径为12.6 mm,轴外最大弥散斑直径为15.8 mm，整个视场的像质比较均匀,分辨率较高，对于波长522 nm的光线，场曲和畸变分别小于15 mm和0.012%，像质优良。     

Infra-red free-carrier absorption due to impurity scattering in semiconducting quantum well structures

The theory of free-carrier absorption (FCA) is developed, in the extreme quantum limit when the carriers are assumed to populate only the lowest quantized energy level, for quasi-two and one-dimensional semiconducting quantum well structures where the carriers are scattered by ionized impurities. The radiation field is assumed to be polarized in the plane of the layer in the quasi-two-dimensional case and along the length of the wire in the quasi-one-dimensional case. Expressions for FCA are obtained for the cases where the impurities are either in the well (background impurities) or outside the well (remote impurities). Variation of FCA is numerically studied with photon frequency and well width.     

Novel model of FM-noise conversion in a UMZI using RF external phase modulation of lasers: Theoretical and experimental results

In this paper, we propose and demonstrate a new and original model for theoretical calculation and experimental measurement of the noise power spectral density (NPSD) in phase-modulated optical links. The phase modulation is operated in the RF frequency range by an external phase modulator. The NPSD is derived for the first time in interferometric systems, by considering all effects such as the 1/f FM noise of the laser and white noise applied to light from a 1550 nm DFB laser, with phase modulation. The results show for the first time the influence of the phase modulation index, modulation frequency and interferometric delay in the phase-to-intensity noise conversion. The experimental and simulation results of conversion of FM-noise to intensity noise in an optical link by considering the external RF phase modulation are shown with good agreement.     

A study of structural, compositional and optical properties of spray-deposited non-stoichiometric (Zn,Fe)S thin films

Non-stoichiometric ternary chalcogenides (Zn,Fe)S were prepared in the film form by pyrolytic spray deposition technique, using air/nitrogen as the carrier gas. The precursor solution comprised of ZnCl₂, FeCl₂ and thiourea. The depositions were carried out under optimum conditions of experimental parameters viz. carrier gas (air/nitrogen) flow rate, concentration of precursor constituents, nozzle substrate distance and temperature of quartz substrate. The deposited thin films were later sintered in argon at 1073 K for 120 min.The structural, compositional and optical properties of the sintered thin films were studied. X-ray diffraction studies of the thin films indicated the presence of (Zn,Fe)S solid solution with prominent cubic sphalerite phase while surface morphology as determined by scanning electron microscopy (SEM) revealed a granular structure.The chemical composition of the resulting thin films as analyzed by energy dispersive X-ray analysis (EDAX) reflected the composition of the precursor solutions from which the depositions were carried out with Fe at% values ranging from 0.4 up to 33.SEM micrographs of thin films reveal that the grain sizes of the thin films prepared using air as carrier gas and N₂ as carrier gas are in the vicinity of 300 and 150 nm, respectively.The diffuse transmittance measurements for thin films, as a function of wavelength reveal the dependence of direct optical band gap on Fe content and type of phase.