Orientation dependent size effects in thermal buckling and post-buckling of nanoplates with cubic anisotropy

In this work, a continuum model is presented for size and orientation dependent thermal buckling and post-buckling of anisotropic nanoplates considering surface and bulk residual stresses. The model with von-Karman nonlinear strains and material cubic anisotropy of single crystals contains two parameters that reflect the orientation effects. Using Ritz method, closed form solutions are given for buckling temperature and post-buckling deflections. Regarding self-instability states of nanoplates and their recovering at higher temperatures, an experiment is discussed based on low pressurized membranes to verify the predictions. For simply supported nanoplates, the size effects are lowest when they are aligned in [100] direction. When the edges get clamped, the orientation dependence is ignorable and the behavior becomes symmetric about [510] axis. The surface residual stress makes drastic increase in buckling temperature of thinner nanoplates for which a minimum thickness is pointed to stay far from material softening at higher temperatures. Deflection of [100]-oriented buckled nanoplates is higher than [110] ones but this reverses at higher temperatures. The results for long nanoplates show that the buckling mode numbers are changed by orientation which is verified by FEM.     

高雷诺数下非混相Rayleigh-Taylor不稳定性的格子Boltzmann方法模拟

本文采用相场格子Boltzmann方法研究了竖直微通道内中等Atwoods数流体的单模Rayleigh-Taylor不稳定性问题,系统分析了雷诺数对相界面动力学行为以及扰动在各发展阶段演化规律的影响.数值结果表明高雷诺数条件下,不稳定性界面扰动的增长经历了四个不同的发展阶段,包括线性增长阶段、饱和速度阶段、重加速阶段及混沌混合阶段.在线性增长阶段,我们计算获得的气泡与尖钉振幅符合线性稳定性理论,并且线性增长率随着雷诺数的增加而增大.在第二个阶段,我们观察到气泡与尖钉将以恒定的速度增长,获得的尖钉饱和速度略高于Goncharov经典势能模型的解析解[Phys.Rev.Lett.200288134502],这归因于系统中产生了多个尺度的旋涡,而涡之间的相互作用促进了尖钉的增长.随着横向速度和纵向速度的差异扩大,气泡和尖钉界面演化诱导产生的Kelvin–Helmholtz不稳定性逐渐增强,从而流体混合区域出现许多不同层次的涡结构,加速了气泡与尖钉振幅的演化速度,并在演化后期阶段,导致界面发生多层次卷起、剧烈变形、混沌破裂等行为,最终形成了非常复杂的拓扑结构.此外,我们还统计了演化后期气泡与尖钉的无量纲加速度,发现气泡和尖钉的振幅在后期呈现二次增长规律,其增长率系数分别为0.045与0.233.而在低雷诺条件下,重流体在不稳定性后期以尖钉的形式向下运动而轻流体以气泡的形式向上升起.在整个演化过程中,界面变得足够光滑,气泡与尖钉在后期的演化速度接近于常数,未观察到后期的重加速与混沌混合阶段.     

Capturing the experimental behaviour of a point-absorber WEC by simplified numerical models

The paper presents a wave basin experiment of a direct-driven point-absorber wave energy converter moving in six degrees of freedom. The goal of the work is to study the dynamics and energy absorption of the wave energy converter, and to verify under which conditions numerical models restricted to heave can capture the behaviour of a point-absorber moving in six degrees of freedom. Several regular and irregular long-crested waves and different damping values of the power take-off system have been tested. We collected data in terms of power output, device motion in six degrees of freedom and wave elevation at different points of the wave basin. A single-body numerical model in the frequency domain and a two-body model in the time domain are used in the study. Motion instabilities due to parametric resonance observed during the experiments are discussed and analysis of the buoy motion in terms of the Mathieu instability is also presented. Our results show that the simplified models can reproduce the body dynamics of the studied converter as long as the transverse non-linear instabilities are not excited, which typically is the case in irregular waves. The performance of the more complex time domain model is able to reproduce both the buoy and PTO dynamics, while the simpler frequency domain model can only reproduce the PTO dynamics for specific cases. Finally, we show that the two-body dynamics of the studied wave energy converter affects the power absorption significantly, and that common assumptions in the numerical models, such as stiff mooring line or that the float moves only in heave, may lead to incorrect predictions for certain sea states.     

基于DIS数字信息化系统对透光物质透光性能的研究

采用DIS数字信息化系统,对不同浓度的蓝墨水溶液在激光光源照射下的透射平均照度及照度分布图像进行实验研究,得到了平均照度值随溶液浓度变化的规律。对不同颜色塑料膜片对白炽灯光源透过照度值及照度分布图像进行实验研究得到及其相关之规律。     

Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension

The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.     

有源光放大器链路中交叉相位调制的不稳定性

利用两种方法研究了有源放大器波分复用系统光纤链路中交叉 相位调制的不稳定性．首先利用非线性薛定谔耦合方程，在小幅度扰动下，研究了正常色散 和反常色散光纤中的交叉相位调制不稳定性. 由于相位噪声涨落，利用分裂步长傅里叶 变换法与Monte-Carlo法，模拟了有源放大器链路中反常色散和正常色散情况下的调制不稳定性. 两种方法得到的结论基本一致. 关键词： 调制不稳定性 交叉相位调制 斯托克斯带 反斯托克斯 带     

Diffusion in poro‐plastic media

A model is developed for the flow of a slightly compressible fluid through a saturated inelastic porous medium. The initial‐boundary‐value problem is a system that consists of the diffusion equation for the fluid coupled to the momentum equation for the porous solid together with a constitutive law which includes a possibly hysteretic relation of elasto‐visco‐plastic type. The variational form of this problem in Hilbert space is a non‐linear evolution equation for which the existence and uniqueness of a global strong solution is proved by means of monotonicity methods. Various degenerate situations are permitted, such as incompressible fluid, negligible porosity, or a quasi‐static momentum equation. The essential sufficient conditions for the well‐posedness of the system consist of an ellipticity condition on the term for diffusion of fluid and either a viscous or a hardening assumption in the constitutive relation for the porous solid. Copyright © 2004 John Wiley & Sons, Ltd.     

Adaptive remeshing for ductile fracture prediction in metal formingRemaillage adaptatif pour la prévision de la rupture ductile en mise en forme

The analysis of mechanical structures using the Finite Element Method in the framework of large elastoplastic strain, needs frequent remeshing of the deformed domain during computation. Indeed, the remeshing is due to the large geometrical distortion of finite elements and the adaptation to the physical behavior of the solution. This paper gives the necessary steps to remesh a mechanical structure during large elastoplastic deformations with damage. An important part of this process is constituted by geometrical and physical error estimates. The proposed method is integrated in a computational environment using the ABAQUS/Explicit solver and the BL2D-V2 adaptive mesher. To cite this article: H. Borouchaki et al., C. R. Mecanique 330 (2002) 709–716.     

BEPC中电子云导致的束团横向尺寸增长研究

多束团正电子储存环中可能发生电子云不稳定性. 由于电子云导致的束团横向尺寸增长已经成为提高对撞机对撞亮度的主要限制因素之一. 介绍了在BEPC储存环中, 利用条纹相机直接测量由于电子云导致的束团横向尺寸增长结果, 并与模拟计算进行了比较.