上海光源储存环磁聚焦结构设计

上海光源是一台正在建设中的低发射度第三代同步辐射光源. 经过优化后, 储存环有两种直线节长度, 周长432m,在能量3.5GeV下束流发射度为3.9nm.rad, 直线节处的β函数和色散函数有足够的调节范围. 跟踪研究表明, 即使带上磁铁高阶场误差, 储存环仍有足够大的动力学孔径和能量接受度.     

HIRFL与CSR的匹配研究

国家重大科学工程HIRFLCSR冷却储存环计划主环CSRm利用已有的HIRFL作为注入器,为了更好地利用HIRFL加速器的能力,对这两台加速器的匹配在原来的初步考虑的基础上进行了较为详细的研究,提出了分别利用HIRFL自己的注入器SFC单独注入到CSR以及SFC加上主加速器SSC注入到CSR的两套方案,既可以提高HIRFL与CSR的总传输效率,又可以在SFC与CSR联合运行的同时使SSC与另建的小回旋加速器组合加速质子,从而充分提高HIRFL的运行效率.     

用于洁净核能源的ADS-EA方案

加速器驱动系统 (ADS)是一种新型的洁净能源装置 ,它采用加速器提供的强流高能量质子束驱动次临界的核反应堆 ,既有安全可靠和产生核废料少的优点 ,还可以处理传统反应堆留下的核废料 .能量放大器是一个基于回旋加速器组合的 ADS方案 ,由三级回旋加速器组成的加速器系统可以产生流强为12 m A和能量为1 .2 Ge V的质子束 (束流功率1 4.4MW) ,用以驱动1500 MW的核反应堆. Accelerator Driving System (ADS) is a new device for cleaning energy. A high intensity, high power proton beam provided by accelerators is used to drive a sub critical nuclear reactor. It is safe, reliable and can produce less nuclear waste, and also can be used to treat the nuclear waste from the classical reactor. An Energy Amplifier (EA), which is composed of three cyclotrons, is one type of ADS. It will be used to produce 14.4 MW proton beam (12 mA, 1.2 GeV) and to operate a 1 500 MW nuclear reactor.     

上海质子医疗装置的涡流效应

 涡流效应是较快重复频率加速器必须考虑的问题。涡流效应引入的六极、四极、二极分量,以及发热效应都会对环的参数如色品、工作点、共振、能量漂移等产生影响。通过计算引入不同效应的强度,模拟了各种效应对环参数的影响,并针对不同升能曲线和升能频率引入涡流效应的计算和比较,得出了在目前考虑的频率范围内,对主环影响较大的效应为六极场,其它效应的影响需要较大的重复频率。并以此为依据选择了最终的工作曲线为半正弦,上升时间为0.7 s。     

上海光源增强器动态升能过程分析

上海光源增强器采用FODO型磁聚焦结构, 由28个FODO单元组成, 周长180m, 可将直线加速器引出的100MeV的电子束加速至3.5GeV, 用于储存环的注入, 重复频率为2Hz. 增强器的动态升能过程将直接影响到储存环的注入效率. 报告上海光源增强器动态升能过程中磁铁磁场、高频电压的上升过程、涡流效应及影响以及束流参数的变化等.     

Linear optics calibration and nonlinear optimization during the commissioning of the SSRF storage ring

Phase I commissioning of the SSRF storage ring on 3.0 GeV beam energy was started at the end of December 2007. A lot of encouraging results have been obtained so far. In this paper, calibrations of the linear optics during the commissioning are discussed, and some measured results about the nonlinearity given. Calibration procedure emphasizes correcting quadrupole magnetic coefficients with the Linear Optics from Closed Orbit (LOCO) technique. After fitting the closed orbit response matrix, the linear optics of the four test modes is substantially corrected, and the measured physical parameters agree well with the designed ones.     

Tune optimization of the third generation light source storage ring based on Frequency Map Analysis

Tune optimization is necessary to optimize the nonlinearity of the third generation light source storage ring. In this paper we summarize the common strategies for choosing a tune and discuss tune op- timization. Frequency Map Analysis （FMA） is applied as a tune scanning tool to reveal information about nonlinear resonances and guide the tune optimization. The Shanghai Synchrotron Radiation Facility （SSRF） storage ring is taken as a test lattice, and the optimum solutions are presented in this paper. Moreover, the third order regular structural resonances excited by sextupoles are particularly investigated, and it is found that these resonances distort the tune shifts with amplitude and show a stop-band like the linear structural resonances.     

Linear optics calibration and nonlinear optimization during the commissioning of the SSRF storage ring

Phase I commissioning of the SSRF storage ring on 3.0 GeV beam energy was started at the end of December 2007. A lot of encouraging results have been obtained so far. In this paper, calibrations of the linear optics during the commissioning are discussed, and some measured results about the nonlinearity given. Calibration procedure emphasizes correcting quadrupole magnetic coefficients with the Linear Optics from Closed Orbit (LOCO) technique. After fitting the closed orbit response matrix, the linear optics of the four test modes is substantially corrected, and the measured physical parameters agree well with the designed ones.     

上海光源介绍

<正>2009年4月29日,上海张江高科技园区一个巨大的鹦鹉螺形状的建筑内,上海同步辐射光源正式举办了其竣工典礼。上海光源是目前世界上性能最好的第三代同步辐射光源之一,也是我国迄今为止投资最高、规模最大的大科学装置,其建成标志     

基于LOCO的上海光源储存环线性光学参数校正

 为了测量和校正线性光学参数,在上海光源储存环调束过程当中使用了基于响应矩阵的线性光学参数分析(LOCO)的方法。介绍了应用LOCO进行计算和校正的过程,包括：数值模拟得到束流位置探测器的测量精度对拟合结果的影响,调整四极铁电源电流强度来校正工作点和beta函数周期性的恢复。测量结果表明,在四极铁强度调整幅度在1.5%以内的情况下,储存环的束流光学参数成功地恢复到和设计值相当接近的状态,beta函数和色散函数畸变小于1%。通过束流光学参数的校正,使得在今后的工作当中可以轻松地控制储存环的工作模式。