溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

环境对MgB_2氧化过程中MgO晶须生长形状的影响

用扫描电镜研究了在 Mg B2 氧化过程中环境对 Mg O晶须生长形状的影响。仅有 Mg B2 时 ,在 80 0℃左右空气气氛中 ,可生长出纳米尺寸的 Mg O晶须。若把 Mg B2 添加到氧化铝陶瓷基体中 ,则生长成竹节状晶须。Mg O晶须生长形状的差别可能是由于氧浓度以及位错等因素造成的。     

丙烷在无机膜反应器中的芳构化

研究了在固定床反应器和膜反应器中的丙烷芳构化，考察了ＨＺＳＭ－５担载的Ｇａ和Ｐｔ－Ｇａ催化剂对反应的影响。结果表明，采用无机膜反应器可以提高丙烷芳构化选择性，从而提高芳烃收率达１０％以上。在膜反应器中，低碳烷烃选择性降低，烯烃选择性增强。固定床相比，膜反应器在低温时对芳构化反应的促进作用最为显著，但是随着温度升高，其促进作用减弱。     

Silicalite-1膜反应器中的丙烷芳构化

在丙烷芳构化反应中，氢气起着相当重要的作用；根据理论分析，消除氢气将会有利于芳构化反应的进行。在Ｓｉｌｉｃａｌｉｔｅ－１沸石分子筛膜反应器，丙烷芳构化反应中的芳烃选择性提高了１０％－２０％。针Ｓｉｌｉｃａｌｉｔｅ－ｌ膜反应器与氧化铝膜反应器中的反应结果相比较，表明膜反应器效果不仅取决于膜的渗透选择性，而且还取决于膜的渗透率。     

贵金属对钴基催化剂上肉桂醛选择加氢反应的影响

 研究了贵金属改性的Co／γ－Al2O3催化剂上的肉桂醛选择加氢反应．结果表明，通过Pt，Pd和Ru贵金属改性，提高了催化剂的活性，但只有Pt改性的催化剂具有较高的选择性．w（Pt）＜0．5％时，催化剂的活性随着Pt含量的增加呈直线升高，当w（Pt）＝0．5％时，催化剂活性可提高近5倍，但催化剂的选择性变化很小．XRD结果表明，催化剂经还原后，γ－Al2O3上的钴主要为α－Co0．TPR结果表明，Pt的加入提高了Co3O4的还原性能，且Pt含量越高，Co3O4的还原温度越低．XPS结果表明，Pt改性的催化剂样品，其Co3O4大部分被还原为Co0．由于Pt与Co具有协同效应，故Pt改性的Co／γ－Al2O3催化剂既具有较高的活性，又具有很高的选择性．     

Effect of Ce<Superscript>3+</Superscript> on spectral characteristic of D1/D2/Cytb559 complex from spinach

It was studied by spectroscopy that PSII reaction center complex consisting of three polypeptides, D₁, D₂ and Cytb559, were purified from PSII particle of CeCl₃ treated spinach. The results of the experiment show that Ce³⁺ could improve the growth of spinach, and accelerate electron transport of PSII particles. Of chl-a of UV-Vis spectrum of D1/D2/Cytb559 complex, Soret band was blue-shifted by 3 nm and Q band by 2 nm, respectively, and the fluorescence emission peak was blue-shifted by 5 nm in CeCl₃-treated spinach compared with the one in control. By the extended X-ray absorption fine structure (EXAFS) spectroscopy methods, it has been found that Ce³⁺ is coordinated with 8 nitrogen atoms in the first coordination shell with Ce-N bond length of 0.253 nm, and Ce³⁺ with 6 oxygen atoms in the second coordination shell with Ce-O bond length of 0.32 nm. However, the secondary structure of D1/D2/Cytb559 complex by circular dichroism (CD) spectroscopy has no significant change after CeCl₃ treated. It might be that Ce³⁺ binds to porphyrin rings of chlorophyll and oxygen of amino acid residue of polypeptide in D1/D2/Cytb559 complex, and then accelerates the primary reaction of PSII, intensifies function of P680⁺ primary electron donor of D1/D2/Cytb559, but there is little change in conformation of PSII reaction center complex.     

高酸度下二(2-乙基己基)亚砜萃取钯的机理研究

本文研究了DEHSO在[HCl]=8N条件下萃取Pd(Ⅱ)的机理,通过斜率法、Asmus法、饱和法确定了亚砜的配位数。并通过萃合物的元素分析、紫外光谱和红外光谱的研究推断出萃合物的组成、结构和萃取反应机理。     

Environmentally Stable Polymer Gels with Super Deformability and High Recoverability Enhanced by Sub‐5 nm Particles in the Nonvolatile Solvent

It remains challenging to satisfy the combined performances for hydrogels with excellent mechanical behavior, high deformability, and super recoverability under harsh environmental conditions. In this study, we first established a strong polymer network via the crosslinking of polymer chains on the surfaces of sub‐5‐nm calcium hydroxide nanospherulites in ethylene glycol solvent. The organic gel expressed excellent mechanical properties such as a recoverable compressive engineering stress of 249 MPa and an elongation stress of 402 KPa, which was attributed to the uniform nanosized crosslinking structure as characterized by SEM. Moreover, the nonvolatile solvent remained in the gel, meaning that the sample can resist a wide temperature range of ?56 to 100 °C without losing the elastic properties. This novel organic gel could provide promising routes to develop the ideal elastic carriers for wearable devices, smart skin sensors, and damping materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 713–721     

Numerical ray-tracing approach with laser intensity distribution for LIDAR signal power function computation

We have developed a new numerical ray-tracing approach for LIDAR signal power function computation, in which the light round-trip propagation is analyzed by geometrical optics and a simple experiment is employed to acquire the laser intensity distribution. It is relatively more accurate and flexible than previous methods. We emphatically discuss the relationship between the inclined angle and the dynamic range of detector output signal in biaxial LIDAR system. Results indicate that an appropriate negative angle can compress the signal dynamic range. This technique has been successfully proved by comparison with real measurements.