Energy contribution of heterocyclic sulfur and a disulfide bond in solid and gaseous phase

Structural Chemistry - In the present work, the energy contribution of the sulfur atom in a heterocycle and in a disulfide bond in solid and gas phases was calculated. To achieve this goal,...     

Synthesis and characterization of cellulose acetate from cellophane industry residues. Application as acetaminophen controlled-release membranes

Journal of Thermal Analysis and Calorimetry - Cellophane film production generates cellulosic residues from scraps, edges, and low-quality films. In this work, cellophane was used as a raw material...     

The use of dilatometry aiming to evaluate the metallurgical aspect of coil slump in a hot-rolled medium carbon steel

Journal of Thermal Analysis and Calorimetry - The hot coil slump is a recurrent problem in the manufacturing process of medium and high equivalent carbon steel plates. Even with the success of the...     

Cyclohexane‐1,3‐dione as a derivatizing agent for the analysis of aldehydes by micelar electrokinetic chromatography with diode array detection

Aldehydes are important compounds in a large number of samples, especially food and beverages. In this work, for the first time, cyclohexane‐1,3‐dione (CHD) was used as a derivatizing reagent aiming aldehyde (formaldehyde, acetaldehyde, propionaldehyde, and valeraldehyde) analysis by MEKC‐DAD. The optimized separation of the derivates was performed using a voltage program (+20 kV, 0–15 min.; +23 kV, 15–17 min.) at a temperature of 26°C, and using as the running buffer a mixture containing 100 mmol/L of sodium dodecyl sulfate and 29 mmol/L of sodium tetraborate at pH 9.2, with maximum absorbance at 260 nm. CHD was compared with two other derivatizing agents: 3‐methyl‐2‐benzothiazolinone hydrazone and phenylhydrazine‐4‐sulfonic acid. The CHD‐aldehyde derivatives were also characterized by LC‐MS. The calibration curves for all aldehydes had r² above 0.999 and LODs ranged from 0.01 to 0.7 mg/L. The optimized methodology was applied in sugar cane brandy (cachaça) samples successfully. CHD showed to be an alternative derivatization reagent due to its stability, aqueous solubility, high selectivity and sensitivity, reduced impurities, and simple preparation steps.     

Cyclometallated 1,2,3-triazol-5-ylidene iridium(III) complexes: synthesis,structure, and photoluminescence properties

1. Download high-res image (67KB)
2. Download full-size image

     

Binuclear copper(II) complex with 2-imidazolylbenzothiazole and bridged chloride ligands

1. Download : Download high-res image (81KB)
2. Download : Download full-size image

     

Rapid and easy quantification of elemental sulphur in aqueous samples from biological reactors: the turbidimetric method revisited

Recent developments in wastewater treatment have led to a renewed interest to obtain elemental sulphur (S°) as a by-product from bioreactors. However, practical studies are limited by the gap of adequate analytical techniques for its determination. This paper provides a statistical study and matrix effect evaluation of an adapted spectrophotometric method for routine S° analyses in aqueous samples, based on a methodology previously described by Hart (1961). Four complex matrices were tested: domestic sewage and effluent samples from three different bioreactors. Tested performance criteria included linearity, matrix effect, limit of detection and quantification and S° recovery. Results were linear (R² = 0.99994) in the studied range (5 to 100 mg S° L^?1) and no matrix effect was observed. The accuracy was based on recovery values that varied from 100% to 106%. The colloidal S° separation and extraction protocol was also considered suitable for aqueous samples, reaching more than 99.0% of S° recovery.     

Enhancing signal-to-noise ratio and resolution in low-field NMR relaxation measurements using post-acquisition digital filters

The traditional way to enhance signal-to-noise ratio (SNR) of nuclear magnetic resonance (NMR) signals is to increase the number of scans. However, this procedure increases the measuring time that can be prohibitive for some applications. Therefore, we have tested the use of several post-acquisition digital filters to enhance SNR up to one order of magnitude in time domain NMR (TD-NMR) relaxation measurements. The procedures were studied using continuous wave free precession (CWFP-T₁) signals, acquired with very low flip angles that contain six times more noise than the Carr–Purcell–Meiboom–Gill (CPMG) signal of the same sample and experimental time. Linear (LI) and logarithmic (LO) data compression, low-pass infinity impulse response (LP), Savitzky–Golay (SG), and wavelet transform (WA) post-acquisition filters enhanced the SNR of the CWFP-T₁ signals by at least six times. The best filters were LO, SG, and WA that have high enhancement in SNR without significant distortions in the ILT relaxation distribution data. Therefore, it was demonstrated that these post-acquisition digital filters could be a useful way to denoise CWFP-T₁, as well as CPMG noisy signals, and consequently reducing the experimental time. It was also demonstrated that filtered CWFP-T₁ method has the potential to be a rapid and nondestructive method to measure fat content in beef and certainly in other meat samples.     

Unexpected formation of dinaphthoaza-17-crown-5 ether containing γ-aminopiperidine subunit

1. Download : Download high-res image (90KB)
2. Download : Download full-size image

     

Effect of nitrogen plasma treatment on the crystallinity and self‐bonding of polyetheretherketone (PEEK) for biomedical applications

Polyetheretherketone (PEEK) is a thermoplastic material with outstanding properties and high potential for biomedical applications, including hermetic encapsulation of active implantable devices. Different biomedical grade PEEK films with initial degree of crystallinity ranging from 8% to 32% (with or without mineral filling) were inspected. PEEK surfaces were treated with nitrogen RF plasma and the effects on materials crystallinity and self‐bonding were evaluated. In particular, the relationship between auto‐adhesive properties and crystalline content of PEEK before and after plasma treatment was examined. PEEK samples showed different bonding strength depending on their degree of crystallinity, with higher self‐bonding performance of mineral‐filled semi‐crystalline films. XRD did not show any modification of the PEEK microstructure as a result of plasma treatment, excluding a significant influence of crystallinity on the self‐bonding mechanisms. Nevertheless, plasma surface treatment successfully improved the self‐bonding strength of all the PEEK films tested, with larger increase in the case of semi‐crystalline unfilled materials. This could be interpreted to the increase in chain mobility that led to interfacial interpenetration of the amorphous phase.