Simple in‐house flow‐injection capillary electrophoresis with capacitively coupled contactless conductivity method for the determination of colistin

An in‐house flow‐injection capillary electrophoresis with capacitively coupled contactless conductivity detection method was developed for the direct measurement of colistin in pharmaceutical samples. The flow injection and capillary electrophoresis systems are connected by an acrylic interface. Capillary electrophoresis separation is achieved within 2 min using a background electrolyte solution of 5 mM 2‐morpholinoethanesulfonic acid and 5 mM histidine (pH 6). The flow‐injection section allows for convenient filling of the capillary and sample introduction without the use of a pressure/vacuum manifold. Capacitively coupled contactless conductivity detection is employed since colistin has no chromophore but is cationic at pH 6. Calibration curve is linear from 20 to 150 mg/L, with a correlation coefficient (r²) of 0.997. The limit of quantitation is 20 mg/L. The developed method provides precision, simplicity, and short analysis time.     

Simple and fast analysis of iohexol in human serums using micro‐hydrophilic interaction liquid chromatography with monolithic column

A simple and rapid method based on micro‐liquid chromatography using a synthetic monolithic capillary column was developed for determination of iohexol in human serums, a marker to evaluate the glomerular filtration rate. A hydrophilic methacrylic acid‐ethylene dimethacrylate monolith provided excellent selectivity and efficiency for iohexol with separation time of 3 min using a mobile phase of 40:60 v/v 50 mM phosphate buffer pH 5/methanol. Four serum protein removal, methods using perchloric acid, 50% acetonitrile, 0.1 M zinc sulfate, and centrifuge membrane filter were examined. The method of zinc sulfate was chosen due to its simplicity, compatibility with the mobile phase system, nontoxicity, and low cost. Interday calibration curves were conducted over iohexol concentrations range of 2–500 mg/L (R² = 0.9997 ± 0.0001) with detection limit of 0.44 mg/L. Intra‐ and interday precisions for peak area and retention time were less than 2.8 and 1.4%, respectively. The method was successfully applied to serum samples with percent recoveries from 102 to 104. The method was applied to monitor released iohexol from healthy subject. Compared with the commercially available reversed‐phase high‐performance liquid chromatography method, the presented method provided simpler chromatogram, faster separation with higher separation efficiency and much lower sample and solvent consumption.     

Preparation of a specific monoclonal antibody to asiaticoside for the development of an enzyme-linked immunosorbent assay

Asiaticoside (AS), the major active component of Centella asiatica (L.) Urban, is used as a memory enhancer and for wound healing. We have successfully prepared monoclonal antibodies (MAbs) against AS, and developed an enzyme-linked immunosorbent assay (ELISA) system for its determination. AS was conjugated to the carrier protein bovine serum albumin (BSA), which acted as an immunogen. In order to confirm its immunogenicity, the ratio of hapten in the AS-BSA conjugate was determined by matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOF MS). After immunization, hybridomas secreting MAbs against AS were produced by fusing splenocytes with the mouse myeloma cell line, SP2/0-Ag14. After the screening, anti-asiaticoside MAb 2B4 was obtained. Weak cross-reactivities occurred with madecassoside (7.08%), but no cross-reactivities were observed with other related triterpenoid glycosides (<0.01%). The assay was suitable for quantitating AS in the range of 0.78 to 50 μg mL(-1). A good correlation of AS concentrations in crude extracts of C. asiatica between ELISA and HPLC methods was obtained (r(2) = 0.999). The contents of AS in various cultivated C. asiatica samples were assayed by the newly established ELISA. The recovery rates of AS in the samples were in the range of 95-103% with coefficients of variation of <10%. The intra- and inter-assay variations were 3.9 and 4.5%, respectively. The ELISA method described should prove useful as an analytical tool for quality control and standardization of medicinal plants and pharmaceutical products containing AS.     

Aerobic oxygenation of phenylboronic acid promoted by thiol derivatives under gold-free conditions: a warning against gold nanoparticle catalysis

Oxygenation of phenylboronic acid to phenol is promoted by thiol derivatives such as 2-aminothiophenol under aerobic conditions in water without metal catalyst. A plausible mechanism involves autoxidation of thiol to generate hydrogen peroxide in situ, which converts phenylboronic acid into phenol under basic conditions. Since thiols are often utilized as protective ligands for gold nanoparticles (AuNPs), this result is a warning that excess thiols and free thiols liberated from the Au surface could participate in aerobic oxidations catalyzed by thiol-protected AuNPs.     

Determination of iodide by detection of iodine using gas-diffusion flow injection and chemiluminescence

This work describes development of a flow injection (FI) system for determination of iodide, based on the chemiluminescence (CL) reaction between iodine and luminol. Iodide in the sample zone is oxidized to iodine. Employment of a gas-diffusion (GD) unit allows for selective detection of the generated CL (425 nm). Preliminary results showed for concentrations of less than 2 mg L⁻¹, that signals were irreproducible and that the calibration was not linear.In order to solve these problems, a method of ‘membrane conditioning’ was investigated, in which iodide stream was continuously merged with oxidant to generate I₂ that conditioned the GD membrane and tubing. This minimized surface interaction between the active surface and the I₂ generated from the samples, thus improving both precision and sensitivity. By employing membrane conditioning, it has been possible to reliably detect concentrations down to 0.1 mg L⁻¹.At the optimized condition, an excellent linear calibration (r² = 0.999) was obtained from 0.1 to 1.0 mg L⁻¹. The method was successfully applied to determine iodide in some pharmaceutical products such as potassium iodide tablets and a liquid patent medicine. However, for vitamin tablets, ascorbic acid was found to interfere seriously by causing a negative signal.     

A method of characterising performance of audio loudspeakers for linear alternator applications in low-cost thermoacoustic electricity generators

This paper investigates the feasibility of using commercially available loudspeakers as low-cost linear alternators for thermoacoustic applications, to convert acoustic power to electricity. The design of a purpose built experimental apparatus, in which a high intensity acoustic wave is induced by using a high power woofer, is described. The rig is used to excite loudspeakers (referred here as “alternators”) under test, while a pair of microphones and a laser displacement sensor are used to enable acoustic power measurements. The paper presents a case study in which characteristics of acoustic-to-electric energy conversion of a candidate loudspeaker (alternator) – selected from the viewpoint of general performance, as well as parameters such as: high force factor, low electrical resistance and low mechanical loss – are measured. The measurements of acoustic power absorbed by the alternator and the electric power extracted from it by the load resistor, which allow estimating acoustic-to-electric efficiencies, are presented. The alternator has been tested at different operating frequencies, cone displacements and load resistance values. The measurement results are discussed and compared in detail with the calculations based on the linear acoustics model.     

Significant enhancement of thermal stability in the non-oxidative thermal degradation of bisphenol-A/aniline based polybenzoxazine aerogel

Previously we reported synthesis of a new type of organic aerogel from phenolic resins called polybenzoxazines and their transformation into carbon aerogels. Here, we further investigate the thermal degradation behaviors of both bulk polybenzoxazines and polybenzoxazine aerogels using Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA)/FTIR, and gas chromatography/time of flight-mass spectroscopy (GC/TOF-MS). The activation energy (E_a) of the decomposition step was determined using the Kissinger method. It was found that the polybenzoxazine aerogels exhibit much higher degradation temperatures and char yields than the bulk. The decomposition temperatures at 10% weight loss and the char yields at 800 °C of the bisphenol-A/aniline based polybenzoxazine aerogel increased up to 24% and 97% higher, respectively, than the corresponding bulk values. Kinetic investigation indicated that the decomposition reaction of bulk polybenzoxazine exhibits three stages, whereas that of the polybenzoxazine aerogel features four stages with much higher overall activation energy. The enhanced thermal stability of the aerogel is ascribed to its highly porous structure, which increases the residence time of the primary decomposition products, and hence generates greater opportunity to form secondary reactions.     

Bulk phase separation study by atomic force microscope friction imaging of natural rubber/poly(methyl methacrylate) film

The first observation of bulk phase separation in immiscible natural rubber (NR)/poly(methyl methacrylate) (PMMA) film using atomic force microscopy (AFM) is reported. Three different forms of AFM measurements: topographic, friction force imaging, and nanoindentation have been effectively used to investigate combined morphological and compositional mapping of the NR/PMMA system. The fracture temperature during sample microtoming and material physical properties could be responsible for the observed topographic contrast. The stronger contrast of friction imaging, relative to topographic imaging, is ascribed to local variations in mechanical properties of the phase-separated domains. Friction force imaging associated with nanoindentation response, performed under AFM force mode, highlights the AFM's ability for probing local friction, adhesion, and elastic properties, and for compositional mapping of heterogeneous polymer film. The resulting friction force imaging along with the response of the nanoindentation are in good agreement, indicating that PMMA exists mainly near the modified NR surface.     

Catalytic degradation of polyolefins over hexagonal mesoporous silica: Effect of aluminum addition

Degradations of polypropylene (PP) and polyethylene (PE) over pure hexagonal mesoporous silica and aluminum-containing hexagonal mesoporous silica catalysts were studied in a fixed bed catalytic reactor at 380 and 430 °C, respectively. The thermal and catalytic degradations of both PP and PE in liquid-phase-contact and vapor-phase-contact modes over pure hexagonal mesoporous silica had no significant effect on the product yields. The liquid products were widely distributed in hydrocarbons with boiling point ranges of 36–405 °C. By adding a small amount of aluminum to the hexagonal mesoporous material, aluminium-containing hexagonal mesoporous silica exhibited good performance in cracking heavy molecular weight hydrocarbons into light hydrocarbons. High liquid yields and less coke deposits were obtained in liquid-phase-contact reaction with increasing aluminum content. The liquid products were mainly composed of C₅–C₁₀ hydrocarbons with boiling points of 36–174 °C, and propene, butene, and butane were main components in gaseous products. The effect of degradation temperature was not observed on product yields though degradation rate of polyolefin into liquid products was faster. Conversely, in vapor-phase-contact reaction, an increase in gaseous yield was observed when increasing the amount of aluminum and temperature of the cracking reactor, while the residue yield remained constant.     

Comparative potentiality of Kans grass (Saccharum spontaneum) and Giant reed (Arundo donax) as lignocellulosic feedstocks for the release of monomeric sugars by microwave/chemical pretreatment

Two-stage microwave (microwave/NaOH pretreatment followed by microwave/H₂SO₄ pretreatment) was used to release monomeric sugars from Kans grass (Saccharum spontaneum) and Giant reed (Arundo donax). The optimum pretreatment conditions were investigated, and the maximum monomeric sugar yields were compared. The microwave-assisted NaOH and H₂SO₄ pretreatments with a 15:1 liquid-to-solid ratio were studied by varying the chemical concentration, reaction temperature, and reaction time to optimize the amount of monomeric sugars. The maximum amounts of monomeric sugars released from microwave-assisted NaOH pretreatment were 6.8 g/100 g of biomass [at 80 °C/5 min, 5 % (w/v) NaOH for S. spontaneum and at 120 °C/5 min, 5 % (w/v) NaOH for A. donax]. Furthermore, the maximum amounts of monomeric sugars released from microwave-assisted H₂SO₄ pretreatment of S. spontaneum and A. donax were 33.8 [at 200 °C/10 min, 0.5 % (w/v) H₂SO₄] and 31.9 [at 180 °C/30 min, 0.5 % (w/v) H₂SO₄] g/100 g of biomass, respectively. The structural changes of S. spontaneum and A. donax were characterized using Fourier transform infrared spectroscopy and scanning electron microscopy.