Butyl methoxy dibenzoylmethane (BMDM) and octocrylene (OC), common UV-filters in sunscreen products are often used in combination. Together they provide broad spectrum photoprotection from exposure to both UVA- and UVB-light. These UV-filters may, however, undergo photodegradation and generate photodegradants, resulting in a potential loss of photoprotection. It is thus a concern that the photostability testing as described by the ICH Guideline Q1B is not a requirement for sunscreen products in Australia, Europe or the USA. UV-filter photodegradants have in addition been shown to be toxic, highlighting the importance of their separation from the parent UV-filters. An HPLC method was developed and validated to quantitatively determine a combination of these UV-filters in the presence of their photodegradants. Reverse-phase chromatography was employed, using a C18 column and an isocratic mobile phase consisting of methanol/water/acetic acid (89/10/1 v/v). Validation according to the ICH guidelines for linearity, accuracy, precision, sensitivity, specificity and robustness was confirmed. The developed and validated method was then successfully applied to the determination of BMDM and OC in an aqueous cream base, typically used in sunscreens, after photostability testing, according to the ICH Guideline Q1B. In addition, the diketo-enol ratio of BMDM in methanol-d4 was determined by NMR and the two major photodegradants were identified by FTMS and LC–MS.
Butyl methoxy dibenzoylmethane (BMDM) and octocrylene (OC), common UV-filters in sunscreen products are often used in combination. Together they provide broad spectrum photoprotection from exposure to both UVA- and UVB-light. These UV-filters may, however, undergo photodegradation and generate photodegradants, resulting in a potential loss of photoprotection. It is thus a concern that the photostability testing as described by the ICH Guideline Q1B is not a requirement for sunscreen products in Australia, Europe or the USA. UV-filter photodegradants have in addition been shown to be toxic, highlighting the importance of their separation from the parent UV-filters. An HPLC method was developed and validated to quantitatively determine a combination of these UV-filters in the presence of their photodegradants. Reverse-phase chromatography was employed, using a C18 column and an isocratic mobile phase consisting of methanol/water/acetic acid (89/10/1 v/v). Validation according to the ICH guidelines for linearity, accuracy, precision, sensitivity, specificity and robustness was confirmed. The developed and validated method was then successfully applied to the determination of BMDM and OC in an aqueous cream base, typically used in sunscreens, after photostability testing, according to the ICH Guideline Q1B. In addition, the diketo-enol ratio of BMDM in methanol-d4 was determined by NMR and the two major photodegradants were identified by FTMS and LC–MS. 相似文献
The Arrhenius parameters of the propagation rate coefficient, kp, are determined employing high‐frequency pulsed laser polymerization–size exclusion chromatography (PLP–SEC) for the homologous series of five linear alkyl acrylates (i.e., methyl acrylate (MA), butyl acrylate (BA), dodecyl acrylate (DA), stearyl acrylate (SA), and behenyl acrylate (BeA)) in 1 m solution in butyl acetate (BuAc) as well as in toluene. The comparison of the obtained kp values with the literature known values for bulk demonstrates that no significant solvent influence neither in BuAc nor in toluene on the propagation reaction compared to bulk is detectable. Concomitantly, the kp values in toluene and in BuAc solution display a similar increase with increasing number of C‐atoms in the ester side chain as was previously reported for the bulk systems. These findings are in clear contrast to earlier studies, which report a decrease of kp with increasing ester side chain length in toluene. The additional investigation of the longest and shortest ester side chain acrylate (i.e., BeA and MA) over the entire experimentally available concentration range at one temperature (i.e., 50 °C) does not reveal any general concentration dependence and all observed differences in the kp are within the experimental error.
A recent response on a publication from our team investigating solvent effects on propagation rate coefficients is commented. Among other issues, we point to the fact that the response interprets only a subset of the data provided in our original contribution.
Chemiluminescence (CL) reactions have been widely employed and explored over the past 50 years because they offer unique light emission upon a defined chemical stimulus. In this Minireview, we focus on peroxyoxalate (PO) compounds because they feature very high quantum yields tuneable over the entire visible spectrum, allowing for visible-light detection by the naked eye without the necessity for expensive analytical instruments. Although analytical methods have been extensively described, PO-CL read-out is a strongly emerging field with ample industrial potential. The state-of-the-art PO-CL detection read-out systems for various key analytes is here explored. In particular, structural requirements, recent developments of PO-CL read-out probes and current limitations of selected examples are detailed. Furthermore, innovative approaches and synthetic routes to push the boundaries of PO-CL reactions into biological systems are highlighted. Underpinned by recent contributions, we share perspectives on embedding PO-CL molecules into polymeric materials, which they consider the next step in designing high performance solid-phase read-out systems. 相似文献
Detailed knowledge of the polymerization mechanisms and kinetics of academically and industrially relevant monomers is mandatory for the precision synthesis of tailor‐made polymers. The IUPAC‐recommended pulsed‐laser polymerization–size exclusion chromatography (PLP–SEC) approach is the method of choice for the determination of propagation rate coefficients and the associated Arrhenius parameters for free radical polymerization processes. With regard to specific monomer classes—such as acrylate‐type monomers, which are very important from a materials point of view—high laser frequencies of up to 500 Hz are mandatory to prevent the formation of mid‐chain radicals and the occurrence of chain‐breaking events by chain transfer, if industrially relevant temperatures are to be reached and wide temperature ranges are to be explored (up to 70 °C). Herein the progress and state‐of‐the‐art of high‐frequency PLP–SEC with pulse repetition rates of 500 Hz is reported, with a critical collection of to‐date investigated 500 Hz data as well as future perspectives for the field.
